• Clinical and Experimental Pediatrics
• /
• v.46 no.6
• /
• pp.554-560
• /
• 2003

Purpose : To investigate the teratogenic effect of gamma-ray on the heart of chick embryo. Methods : 50 rad, 100 rad, 150 rad, 200 rad, 250 rad, and 300 rad of gamma-ray were used to irradiate three days old chick embryos. The control group was not irradiated. After three weeks, the embryos were sacrificed and examined for cardiovascular malformation. Results : The survival rate of the gamma-ray irradiated group was significantly lower than that of the control group(33.3-63.3% vs 76.4%, P=0.001). The cardiac malformation rate of the experimental group was 11.0%. In the control group, no congenital cardiac malformations were observed. The experimental groups had a significantly higher malformation rate(P=0.001). The types of malformation were ventricular septal defect, tricuspid atresia, Ebstein anomaly and aortic arch anomaly. In the gamma-ray irradiated group, the cardiac malformations were : 14 small ventricular septal defects (VSDs), five large VSDs, two tricuspid atresias, and one Ebstein anomaly. The higher the dose of radiation applied, the higher the incidence of cardiac malformation was noted. Conclusion : Gamma-ray irradiation of 3 days old chick embryos increased the rate of death and the rate of cardiac malformation significantly.

• The Korean Journal of Air & Space Law and Policy
• /
• v.31 no.2
• /
• pp.37-72
• /
• 2016

In the aerospace field, besides special purpose airplanes, contracts for supply of various types of products such as prototypes, unmanned aerial vehicles and space launch vehicles are increasing. In the case of the contractor, it was planned to spend a large amount of money to supply the production, but if the purchase specification that presents the quality and performance standard of the product is poor or lacks the capacity to judge the performance, consuming enormous amounts of time and money. Even if the undertaker does not have the ability to supply the products with the required performance and quality to achieve the purpose of the contract, he/she must pay the cost of burial due to the incompleteness of the work and the compensation for the cancellation of the contract. In this case, the defendant ordered the plaintiff to supply the aircraft by the Happy Box method, which is capable of ILS Offset flight as specified in the Purchase Specification, but the plaintiff attempted to supply the aircraft by the RNAV method. Although the ILS ground signal can be inspected by the RNAV method, the aircraft manufactured in the manner claimed by the plaintiff does not have the ILS Offset flight function required by the purchase specification, so the defendant can not achieve the purpose required by the purchase specification. It was a question of whether a defendant's cancellation of contract was legitimate. The aircraft, which is the object of this contract, is a subordinate substitute, so the case contract is of undertaking. Therefore, in order to complete the work in this contract, the major structural parts of the aircraft must be manufactured as agreed and have the performance generally required in the social sense. However, the aircraft delivered by the plaintiff has serious defects because the defendant can not achieve the purpose required by the purchase specification due to the lack of the ILS Offset flight function required by the purchase specification. This deficiency is impossible for the plaintiff to repair, so the defendant 's cancellation of the contract is legitimate.

• Clinical and Experimental Pediatrics
• /
• v.49 no.3
• /
• pp.287-291
• /
• 2006

Purpose : Aneurysms of sinus valsalva are rare anormalies thought to be primarily congenital in origin, progressing into death by acute heart failure in cases of rupture. Surgical correction is the only method of treatment. With these clinical implications, we reviewed the clinical characteristics and surgical results of patients with ruptured sinus of valsalva aneurysm. Methods : Between January 1991 and February 2004, 17 patients with ruptured sinus of valsalva aneurysm were retrospectively reviewed for their clinical symptoms, physical findings, past history, coexistent cardiac anormalies, surgical results, and mid-term prognosis. Results : The 17 patients included 13 men and four women, with a mean age of 30 years(10-59 years). Preoperatively accompanying cardiac anormalies were ventricular septal defect(VSD, eight cases of doubly committed juxta-arterial VSD) and aortic insufficiency(11 cases). During operations, patterns of fistulous tracts were found to be right colonary sinus-right ventricle in 13 patients, right coronary sinus-right atrium in one, noncoronary sinus - right ventricle in two, noncoronary sinus - right atrium in one, and VSD was noticed in 14 patients(all were doubly committed juxta-arterial in type). The defects were closed with a patch in 13 patients, without a patch in four, with concommitant aortic valve replacement in four and with aortic valvuloplasty in two. There were no mortalities during operations or the mid-term follow-up periods($40{\pm}49$ months). Conclusion : Because, at least in Orientals, VSD(especially doubly committed juxta-arterial) was accompanied in large numbers of patients with aneurysms of sinus valsalva, preoperative evaluations of this congenital heart disease should be made very careful. And we may need to revise the algorithm of treatment policy in small sized doubly committed juxta-arterial VSD.

• Food Science of Animal Resources
• /
• v.27 no.2
• /
• pp.185-189
• /
• 2007

Animals must be inspected prior to and after slaughter to make certain they are free of diseases and unacceptable defects. Since meats are potentially hazardous foods, they should not be accept if there are any signs of contamination, temperature abuse, or spoilage. This survey was aimed to monitor the current situation of country-of-origin labels and sanitation for the meat markets in Seoul, Korea. The markets were divided into groups as to 25 territories in Seoul and the size of markets (large size, medium size, and small size). In terms of size distribution, small butcher shops occupied the highest percentage. On the itemized suitability test of unpacked and packed beer in Seoul, most butcher shops showed good evaluation. However, labels indicating the grade, storage and cooking instruction for unpacked beef were not properly posted on the products. The results of monitoring sanitation conditions for butcher shops in Seoul showed relatively low suitability. Especially, there were serious lack of knowledge about wearing the sanitation clothings, caps, and shoes. The problem with food safety is so complicated that producers, consumers, merchandisers, the press, the government and the scholar should try to solve the problems altogether. Also, it is important to educate and provide them with correct understanding and information for food hygiene and safety.

• Asia pacific journal of information systems
• /
• v.19 no.2
• /
• pp.157-178
• /
• 2009

Corporate credit rating is a very important factor in the market for corporate debt. Information concerning corporate operations is often disseminated to market participants through the changes in credit ratings that are published by professional rating agencies, such as Standard and Poor's (S&P) and Moody's Investor Service. Since these agencies generally require a large fee for the service, and the periodically provided ratings sometimes do not reflect the default risk of the company at the time, it may be advantageous for bond-market participants to be able to classify credit ratings before the agencies actually publish them. As a result, it is very important for companies (especially, financial companies) to develop a proper model of credit rating. From a technical perspective, the credit rating constitutes a typical, multiclass, classification problem because rating agencies generally have ten or more categories of ratings. For example, S&P's ratings range from AAA for the highest-quality bonds to D for the lowest-quality bonds. The professional rating agencies emphasize the importance of analysts' subjective judgments in the determination of credit ratings. However, in practice, a mathematical model that uses the financial variables of companies plays an important role in determining credit ratings, since it is convenient to apply and cost efficient. These financial variables include the ratios that represent a company's leverage status, liquidity status, and profitability status. Several statistical and artificial intelligence (AI) techniques have been applied as tools for predicting credit ratings. Among them, artificial neural networks are most prevalent in the area of finance because of their broad applicability to many business problems and their preeminent ability to adapt. However, artificial neural networks also have many defects, including the difficulty in determining the values of the control parameters and the number of processing elements in the layer as well as the risk of over-fitting. Of late, because of their robustness and high accuracy, support vector machines (SVMs) have become popular as a solution for problems with generating accurate prediction. An SVM's solution may be globally optimal because SVMs seek to minimize structural risk. On the other hand, artificial neural network models may tend to find locally optimal solutions because they seek to minimize empirical risk. In addition, no parameters need to be tuned in SVMs, barring the upper bound for non-separable cases in linear SVMs. Since SVMs were originally devised for binary classification, however they are not intrinsically geared for multiclass classifications as in credit ratings. Thus, researchers have tried to extend the original SVM to multiclass classification. Hitherto, a variety of techniques to extend standard SVMs to multiclass SVMs (MSVMs) has been proposed in the literature Only a few types of MSVM are, however, tested using prior studies that apply MSVMs to credit ratings studies. In this study, we examined six different techniques of MSVMs: (1) One-Against-One, (2) One-Against-AIL (3) DAGSVM, (4) ECOC, (5) Method of Weston and Watkins, and (6) Method of Crammer and Singer. In addition, we examined the prediction accuracy of some modified version of conventional MSVM techniques. To find the most appropriate technique of MSVMs for corporate bond rating, we applied all the techniques of MSVMs to a real-world case of credit rating in Korea. The best application is in corporate bond rating, which is the most frequently studied area of credit rating for specific debt issues or other financial obligations. For our study the research data were collected from National Information and Credit Evaluation, Inc., a major bond-rating company in Korea. The data set is comprised of the bond-ratings for the year 2002 and various financial variables for 1,295 companies from the manufacturing industry in Korea. We compared the results of these techniques with one another, and with those of traditional methods for credit ratings, such as multiple discriminant analysis (MDA), multinomial logistic regression (MLOGIT), and artificial neural networks (ANNs). As a result, we found that DAGSVM with an ordered list was the best approach for the prediction of bond rating. In addition, we found that the modified version of ECOC approach can yield higher prediction accuracy for the cases showing clear patterns.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.4
• /
• pp.10-39
• /
• 1988

This study investigated the temperatures and relative humidities in the semi-greenhouse type solar dryer with a black rock-bed heat storage and without heat storage and outdoor temperature and relative humidity at 9 a.m. and 2 p.m.. A comparison was made of the drying rates, final moisture contents, moisture content distributions, casehardening stresses, drying defects, volumetric shrinkage of dried lumber for solar- and air-drying from the green condition of mixtures of Douglas-fir, lauan, taun, oak and sycamore 25mm- and 50 mm-thick lumber during the same period for four seasons, and heat efficiencies for solar dryer with and without the heat storage for saving of heat energy and the cost of lumber drying using the solar energy. The results from this study were summarized as follows: I. The mean weekly temperatures in the solar dryers were 3 to $6^{\circ}C$ at 9 a.m. and 9 to $13^{\circ}C$ at 2 p.m. higher than mean outdoor temperature during all the drying period. 2. The mean weekly relative humidities in the solar dryers were about 1 to 19% at 9 a.m. higher than the outdoor relative humidity. and the difference between indoor and outdoor relative humidity in the morning was greater than in the afternoon. 3. The temperatures and relative humidities in the solar dryer with and without the heat storage were nearly same. 4. The overall solar insolation during the spring months was highest and then was greater in the order of summer, atumm, and winter month. S. The initial rate of solar drying was more rapid than that of air drying. As moisture content decreased, solar drying rate became more rapid than that of air drying. The rates of solar drying with and without heat storage were nearly same. The drying rate of Douglas-fir was fastest and then faster in the order of sycamore, lauan, taun and oak. and the faster drying rate of species, the smaller differences of drying rates between thicknesses of lumber. The drying rates were fastest in the summer and slowest in the winter. The rates of solar drying during the spring were more slowly in the early stage and faster in the later stage than those during the autumn. 6. The final moisture contents were above 15% for 25mm-thick air dried and about 10% for solar dried lumber, but the mean final MCs for 50mm-thick lumber were much higher than those of thin lumber. The differences of final MC between upper and lower course of pile for solar drying were greater than those of pile for air drying. The differences of moisture content between the shell and the core of air dried lumbers were greater than those of solar dried lumber, smallest in the drying during summer and greatest in the drying during winter among seasons. 7. Casehardening stresses of 25mm- and 50mm-thick dried lumber were slight, casehardening stress of solar dried lumber was severer than that of air dried lumber and was similar between solar dried lumber with and without heat storage, Casehardening stresses of lumber dried during spring were slightest and then slighter in the order of summer, autumn, and winter. Casehardening stresses of Douglas -fir, sycamore and lauan were slight, comparing with those of taun and oak. 8. Maximum initial checks of 25mm-thick lumber occurred above and below fiber saturation point and those of 50mm-thick lumber occurred in the higher moisture content than thin lumber. As the moisture content decreased, most of checks were closed and didn't show distinct difference of the degree of checks among drying methods. The degree of checks were very slight in case of Douglas-fir and lauan, and severe in case of taun and oak. The degree of checks for 50mm-thick lumber were severer than those for 25mm-thick lumber. 9. The degree of warpage showed severe in case of oak and sycamore lumber, but no warping was found in case of Douglas-fir, lauan and taun. 10. The volumetric shrinkages of taun and oak were large and medium in case of Douglas-fir, lauan and sycamore. 11. Heat efficiencies of solar dryer with heat storage were 6.9% during spring, 7.7% during summer, 12.1% during autumn and 4.1% during winter season. Heat efficiency of solar dryer with heat storage was slightly greater than that of without heat storage. As moisture content of lumber decreased, heat efficiency decreased.

• Clinical and Experimental Reproductive Medicine
• /
• v.31 no.3
• /
• pp.183-190
• /
• 2004

Objectives: Methylenetetrahydrofolate reductase (MTHFR) mutation are commonly associated with hyperhomocysteinemia, and through their defects in homocysteine metabolism, they have been implicated as a risk factor for recurrent spontaneous abortion. Recent report describe that 28-bp tandem repeat polymorphism in thymidylate synthase enhancer region (TSER) that influence enzyme activity would affect plasma homocysteine level. We have investigated the relationship between TSER genotype and plasma homocysteine level in 54 patients with recurrent spontaneous abortion. Methods: Plasma homocysteine level was measured by fluorescent polarizing immunoassay. MTHFR mutation (C677T and A1298C) was identified by PCR-restriction fragment length polymorphism assay and TSER mutation was analyzed by PCR method. The data were analyzed using the program SAS 8.2 for Windows. Results: Total homocysteine level was significantly higher in MTHFR 677TT genotype ($9.80{\pm}3.87{\mu}mol/L$) than MTHFR 677CC genotype ($8.14{\pm}1.74{\mu}mol/L$) in Korean patients with unexplained recurrent spontaneous abortion (p=0.0143). However, the plasma homocysteine level was not significantly different in the MTHFR 1298AA ($8.42{\pm}2.65{\mu}mol/L$) and 1298CC ($6.09{\pm}0.32{\mu}mol/L$; p=0.2058) and, TSER 2R2R ($8.61{\pm}1.68{\mu}mol/L$) and 3R3R ($8.05{\pm}2.81{\mu}mol/L$; p=0.9319) mutant genotypes, respectively. In this study, we found the combination effects of TSER and MTHFR C677T genotypes. Plasma homocysteine levels were the highest ($11.47{\pm}4.66{\mu}mol/L$) in individuals with TSER 3R3R ($8.05{\pm}2.81{\mu}mol/L$) and MTHFR 677TT ($9.80{\pm}3.87{\mu}mol/L$) genotypes. Individuals with a combination of both TSER 2R2R/2R3R and MTHFR 677CC/CT genotypes ($7.69{\pm}1.77{\mu}mol/L$) had lower plasma homocysteine levels than TSER 2R2R ($8.61{\pm}1.68{\mu}mol/L$) and MTHR 677CC ($8.14{\pm}1.74{\mu}mol/L$) genotypes, respectively. The effect of MTHFR polymorphism in the homocysteine metabolism appears to be stronger than that of TSER polymorphism. Conclusion: Although statistically not significant, we found the elevated level of plasma homocysteine in combined genotypes with TSER and MTHFR (C677T and A1298C) in Korean patients with unexplained habitual abortion. In this study, we reported the possibility that TSER polymorphism is a genetic determinant of plasma homocysteine levels in the Korean patients as well as MTHFR C677T polymorphism. A large prospective study is needed to verify our findings.

• The Korean Journal of Nuclear Medicine
• /
• v.37 no.4
• /
• pp.245-253
• /
• 2003

Puorpose: The purpose of this study was to evaluate the usefulness of $^{99m}Tc$ DMSA scintigraphy on the dignosis of a renal scar in children with urinary tract infections. Materials and Methods: Eighty three patients were included in this study, who were diagnosed as the urinary tract infection on the basis of symptom, urinalysis and urine culture. $^{99m}Tc$ DMSA scintigraphy and voiding cystoureterography were peformed within 7days before the treatment in all patients. We classified the scintigraphic findings as follow s : 1 ; a large hypoactive upper or lower pole. 2 ; a small hypoactive area. 3 ; single defect resulting in localized deformity of the outlines. 4 ; deformed outlines in a small or normal sized kidney. 5 ; multiple defects. 6 ; diffuse hypoactive kidney without regional impairment. Follow-up scintigraphy was done at least 6 months after the initial study. When the abnormality on the initial scintigraphy was not completely resolved on the follow-up scan, the lesion was defined as containing a scar. Results: One hundred and fifteen renal units of 166 units(69.3%) showed abnormal findings on the DMSA scintigraphy. 65 units(56.5%) was diagnosed as containing renal scars on follow-up scintigraphies. Incidences of renal scar among renal units showing pattern 3, 4 and 5 on the initial scan was 75%, 78% and 78%, respectively. Whereas many of renal units showing 1, 2 and 6 pattern were recovered(65%, 76%, 50%). Sensitivity, specificity and accuracy of pattern-based DMSA scintigraphic findings on the diagnosis of renal scar was 76.9%, 85.1% and 81.9%, respectively. VUR was significantly associated with the renal scar when the initial DMSA shows unrecoverable findings(pattern 3, 4, 5). Odds ratio of the renal scar in a kidney showing unrecoverable initial scintigraphic findings was 19.1. Odds ratio in a kidney with mild or moderate-to-severe VUR was 3.5 and 14.4 respectively. Conclusion: In the urinary tract infection, renal scar was significantly developed in a kidney showing unrecoverable findings on the initial DMSA scan and VUR on voiding cystoureterography.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.06a
• /
• pp.16-23
• /
• 2000

The increasing functional needs of top-quality printing papers and packaging paperboards, and especially the rapid developments in electronic printing processes and various computer printers during past few years, set new targets and requirements for modern paper quality. Most of these paper grades of today have relatively high filler content, are moderately or heavily calendered , and have many coating layers for the best appearance and performance. In practice, this means that many of the traditional quality assurance methods, mostly designed to measure papers made of pure. native pulp only, can not reliably (or at all) be used to analyze or rank the quality of modern papers. Hence, introduction of new measurement techniques is necessary to assure and further develop the paper quality today and in the future. Paper formation , i.e. small scale (millimeter scale) variation of basis weight, is the most important quality parameter of paper-making due to its influence on practically all the other quality properties of paper. The ideal paper would be completely uniform so that the basis weight of each small point (area) measured would be the same. In practice, of course, this is not possible because there always exists relatively large local variations in paper. However, these small scale basis weight variations are the major reason for many other quality problems, including calender blacking uneven coating result, uneven printing result, etc. The traditionally used visual inspection or optical measurement of the paper does not give us a reliable understanding of the material variations in the paper because in modern paper making process the optical behavior of paper is strongly affected by using e.g. fillers, dye or coating colors. Futhermore, the opacity (optical density) of the paper is changed at different process stages like wet pressing and calendering. The greatest advantage of using beta transmission method to measure paper formation is that it can be very reliably calibrated to measure true basis weight variation of all kinds of paper and board, independently on sample basis weight or paper grade. This gives us the possibility to measure, compare and judge papers made of different raw materials, different color, or even to measure heavily calendered, coated or printed papers. Scientific research of paper physics has shown that the orientation of the top layer (paper surface) fibers of the sheet paly the key role in paper curling and cockling , causing the typical practical problems (paper jam) with modern fax and copy machines, electronic printing , etc. On the other hand, the fiber orientation at the surface and middle layer of the sheet controls the bending stiffness of paperboard . Therefore, a reliable measurement of paper surface fiber orientation gives us a magnificent tool to investigate and predict paper curling and coclking tendency, and provides the necessary information to finetune, the manufacturing process for optimum quality. many papers, especially heavily calendered and coated grades, do resist liquid and gas penetration very much, bing beyond the measurement range of the traditional instruments or resulting invonveniently long measuring time per sample . The increased surface hardness and use of filler minerals and mechanical pulp make a reliable, nonleaking sample contact to the measurement head a challenge of its own. Paper surface coating causes, as expected, a layer which has completely different permeability characteristics compared to the other layer of the sheet. The latest developments in sensor technologies have made it possible to reliably measure gas flow in well controlled conditions, allowing us to investigate the gas penetration of open structures, such as cigarette paper, tissue or sack paper, and in the low permeability range analyze even fully greaseproof papers, silicon papers, heavily coated papers and boards or even detect defects in barrier coatings ! Even nitrogen or helium may be used as the gas, giving us completely new possibilities to rank the products or to find correlation to critical process or converting parameters. All the modern paper machines include many on-line measuring instruments which are used to give the necessary information for automatic process control systems. hence, the reliability of this information obtained from different sensors is vital for good optimizing and process stability. If any of these on-line sensors do not operate perfectly ass planned (having even small measurement error or malfunction ), the process control will set the machine to operate away from the optimum , resulting loss of profit or eventual problems in quality or runnability. To assure optimum operation of the paper machines, a novel quality assurance policy for the on-line measurements has been developed, including control procedures utilizing traceable, accredited standards for the best reliability and performance.

• Korean Journal of Mineralogy and Petrology
• /
• v.34 no.1
• /
• pp.31-40
• /
• 2021

The hydrogen in nominally anhydrous mineral is known to be associated with lattice defects, but it also can exist in the form of water and hydroxyl groups on the large surface of the nanoscale particles. In this study, we investigate the effectiveness of 1H solid-state nuclear magnetic resonance (NMR) spectroscopy as a robust experimental method to quantify the hydrogen atomic environments of amorphous silica nanoparticles with varying relative humidity. Amorphous silica nanoparticles were packed into NMR rotors in a temperature-humidity controlled glove box, then stored in different atmospheric conditions with 25% and 70% relative humidity for 2~10 days until 1H NMR experiments, and a slight difference was observed in 1H NMR spectra. These results indicate that amount of hydrous species in the sample packed in the NMR rotor is rarely changed by the external atmosphere. The amount of hydrogen atom, especially the amount of physisorbed water may vary in the range of ~10% due to the temporal and spatial inhomogeneity of relative humidity in the glove box. The quantitative analysis of 1H NMR spectra shows that the amount of hydrogen atom in amorphous silica nanoparticles linearly increases as the relative humidity increases. These results imply that the sample sealing capability of the NMR rotor is sufficient to preserve the hydrous environments of samples, and is suitable for the quantitative measurement of water content of ultrafine nominally anhydrous minerals depending on the atmospheric relative humidity. We expect that 1H solid-state NMR method is suitable to investigate systematically the effect of surface area and crystallinity on the water content of diverse nano-sized nominally anhydrous minerals with varying relative humidity.