• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.102-103
• /
• 2014

Due to the nature of the existing load, the criteria of assessing the intensity of the lightweight wall's impact resistance has been though of as obscure. The current study, therefore, focuses on the standardized assessment of the impact resistance to the force of the large soft body applying to the lightweight wall. The gypsum board wall showed a low level of the maximum residual displacement. It is, however, required to be careful about the selection of the finishing process since the high level of the maximum displacement is likely to cause harm to finishing materials. Unlike the gypsum board, the ALC block wall displayed a considerable rigidity while showing almost no maximum residual displacement. Even with the low level of the maximum displacement due to the stiffness, the ALC block wall is still likely to be affected by the vibration derived from any impact on the surface, which demands a need for additional study. The future experimental study, accordingly, will focus on the impact of the vibration on finishing materials, consequently leading to the accurate prediction of the possibility of potential damage to the lightweight wall caused by the large soft body.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.182-183
• /
• 2014

In case of large soft body impact test at the construction site, the test conditions are different from conditions at the laboratory, and the length of rope to hold the impact specimen must be changed. In a previous study, the fact that the size of impact load is varied by the length of rope on the large soft body impact specimen was confirmed. In this study, the length of rope and fall height were set as independent variables to conduct the load analysis test. It was determined that the load fluctuation was occurred depending on the length of rope under the fall height over 100 mm, and it is concluded that the additional setup of fall height to modify the actual impact load size is required when the length of rope is below 2.5 m. In this study, the modified formula to put equal size of impact load regardless of the length of rope was extracted through the experiment.

• Geomechanics and Engineering
• /
• 제32권2호
• /
• pp.145-157
• /
• 2023

This paper aims at investigating the face stability of large-diameter underwater shield tunnels considering seepage in soft-hard uneven strata. Using the kinematic approach of limit upper-bound analysis, the analytical solution of limit supporting pressure on the tunnel face considering seepage was obtained based on a logarithmic spiral collapsed body in uneven strata. The stability analysis method of the excavation face with different soft- and hard-stratum ratios was explored and validated. Moreover, the effects of water level and burial depth on tunnel face stability were discussed. The results show the effect of seepage on the excavation face stability can be accounted as the seepage force on the excavation face and the seepage force of pore water in instability body. When the thickness ratio of hard soil layer within the excavation face exceeds 1/6D, the interface of the soft and hard soil layer can be placed at tunnel axis during stability analysis. The reliability of the analytical solution of the limit supporting pressure is validated by numerical method and literature methods. The increase of water level causes the instability of upper soft soil layer firstly due to the higher seepage force. With the rise of burial depth, the horizontal displacement of the upper soft soil decreases and the limit supporting pressure changes little because of soil arching effect.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 춘계 학술논문 발표대회
• /
• pp.181-182
• /
• 2015

The use of non-bearing light weight wall has increased recently due to the increase of high-rise buildings and supply of long-life housing. Light weight wall has advantages such as reducing the self-weight of the building, convenience in installation, and shortening construction period, however, must have a sufficient strength to external force. This study standardized the impact resistance test method for light weight walls by using the actual impact load obtained through load analysis test in previous studies. The impact resistance test method was divided into the test method that uses soft body and the one that uses hard body. The size of specimen was set up as height 2.4m and width 3.0m. The size and shape of the body followed those used in BS 5234-2 and so on for the compatibility with the test method used overseas. The judgment criteria for impact resistance based on test results were not defined uniformly as the assessment of functional damage can vary depending on the type of material, structural method, purpose of wall, and so on even when the same impact load was applied.

• 로봇학회논문지
• /
• 제17권1호
• /
• pp.68-75
• /
• 2022

In this paper, we considered the deformation shape of the soft rotation actuator as a double curvature shell and proceeded with the analytical development. Since the response of the hyperelastic material has a large nonlinear deformation, the analytical approach is very complicated and the solution cannot be easily obtained. it is assumed that the behavior of the flexible body, which is a superelastic material, takes the form of a double curvature shell, and the formulas for calculating the deformation are simplified. In this process, equilibrium equations in the related coordinate system representing a double curvature shell were derived. In addition, assuming a thin shell, the stress component in the thickness direction was ignored, and the equation was developed by adding the assumption of free rotation without load. In order to verify the analytically calculated value in this way, an experiment was conducted and the results were compared.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.486-493
• /
• 2006

This paper deals with the procedure and the results on the dynamic loading tests of two large diameter - long drilled shafts (diameter=2.0m, length=75m) which were embedded into weathered rocks through thick soft marine clays and sandy gravels. Prior to the real dynamic loading test, the numerical simulation for the test procedure was performed to check the structural stability of the main pile body using equivalent static elastic analysis and the application of the hammer system using WEAP (Wave Equation Analysis of Pile Driving). Through these preliminary analyses the dynamic loading tests on large diameter - long drilled shafts have been successfully achieved.

• 한국의류산업학회지
• /
• 제23권6호
• /
• pp.781-789
• /
• 2021

To enhance the design and comfort of waist-protection corsets, this study analyzed the product characteristics of five types of posture-correction corsets that are available commercially. Additionally, subjective evaluation of the corsets was conducted on women aged 20 to 60 years, in terms of design, material preference, fit, comfort, degree of correction, freedom of movement, tightness, and convenience of front fastening. Following product analysis, the five corset types were divided into: two soft, one semi-hard, and two hard types in terms of the degree of elongation. As a result of pattern analysis, the soft type was designed to improve fit by reflecting the body curvature, whereas the semi-hard and hard types were relatively flat. Through the wearing sensation assessment, the hard type manufactured by company S was the best in terms of design, material, fit, comfort, correction degree, and freedom of movement. The soft type was average in design, material, and fit while relatively poor in the correction degree and tightness. The results indicated that soft materials, flexible bones with appropriate tension, patterns designed to snugly fit the body with large curvature at the top and bottom for better inflection, and adjustable support belts that can be double-fixed are crucial elements in improving the corset design to boost the comfort of wearing. These study results are helpful in the development of waist-protection corsets with excellent wearing comfort and design appreciated by customers.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제34권6호
• /
• pp.653-656
• /
• 2008

Mesenchymal chondrosarcoma is a rare malignant tumor of bone and soft tissue. This aggressive form of chondrosarcoma represents only 3% to 9% of all chondrosarcomas. This neoplasm is characterized by sheets or clusters of undifferentiated spindle or round cells surrounding discrete nodules of well-differentiated cartilage. We experienced a case of mesenchymal chondrosarcoma on mandibular body. Two years ago, the patient had been treated the intrabony cystic lesion on mandiblular left body. At that time, cartilage portion was not detected in the cystic specimen. Two years after cyst enucleation, the recurred large neoplasm in the mandibular left body was noted, and it was diagnosed as 4.5 cm sized mesenchymal chondrosarcoma. The mandibular tumor was widely resected and rigid-plate and cervical musculocutaneous flap were used for reconstruction of resected bone and soft tissues. No complications and recurrence were noted for 6 months postoperatively.

• Archives of Plastic Surgery
• /
• 제32권4호
• /
• pp.428-434
• /
• 2005

Extensive and complicated defects on the body call for an omnipotent tool for a perfect reconstruction. Flaps derived from the omentum has many advantages over the conventional flaps. From 1999 to 2004, Omental flaps were applied for various soft tissue reconstructions. Among total 20 total 7 cases were for immediate reconstruction, 2 cases for chronic infection, 3 cases for simultaneous reconstruction of two defects, 4 cases for functional joint reconstruction and 4 cases were for flow- through revascularization. Among these cases, 3 cases were operated with minimal incision harvest technique. There were no complete flap failures, partial necrosis of the distal parts were noted on three cases. The omental flap is indicated on a large contaminated defect reconstruction due to its large size, well-vascularized, and malleable properties. The omental flap provides several additional advantages over other flaps, which are; the availability of the one staged simultaneous reconstruction of two defects with one flap, providing gliding function for the joint motion, and a flow-through characteristics with long vascular pedicle. But there are some serious shortcomings, including a long abdominal scar and intraabdominal problems. However, these are rare and can be minimized with our minimal incision technique. Due to its unique characteristics. the omentum is one of the ideal tissues for the reconstruction of the complicated soft tissue defects due to its unique characteristics.

• Restorative Dentistry and Endodontics
• /
• 제22권2호
• /
• pp.519-535
• /
• 1997

The responses of human pulp fibroblastic cells to Ga-As Semi-Conductor-Dens-Bio Laser (Frequency: 5 Hz~10,000 Hz Model: SD-101A RCA, U.SA)) were examined in vitro using pulp fibroblastic cells obtained from the pulp tissue of human tooth. The mitogenic effect of soft laser was assessed by measuring the MTT assay. The morphologic effect for soft laser showed under the scanning and transmission electron microscopy. The results as follows; 1. The mitogenic response of the soft laser was not observed until 4th time of radiation, while the mitogenic response at 4th time increased mitogenic effect by as much as 1.7 fold compared to the control value. 2. The mitogenic response of the soft laser on pulp fibroblast differ from the mitogenic response on other fibroblasts. 3. In scanning electron microscopic study, The microvilli of cell surface increased gradually with width and length after laser radiation, it demonstrate that development of microvilli have close connection with differentiation of cells. 4. Under the transmission electron microscope, The laser-treated cells maintained their elongated shape and a high degree of cellular polarization. The large cell body containing a well developed Golgi complex, a large number of profiles of rough endoplasmic reticulum, and great numbers of mitochondria. 5. The laser-treated cells maintained the long straight bundles of closely apposed microfilaments or individual filaments forming a cross-linked network. These findings suggest that the laser may have important roles in promotion of pulp healing and consequently may be useful for clinical application in pulp regenerative procedures.