• Korean Journal of Applied Biomechanics
• /
• v.28 no.2
• /
• pp.93-100
• /
• 2018

Objective: The purpose of this study is to analyze the kinematic characteristics of the national speed skaters in the curve phase of 500-m race. Method: Seven national skaters participated in the study. Race images were acquired using a high - speed camera, and the three-dimensional motion was analyzed. Results: For skaters, whose average velocity in the curve phase is high, the velocity of entry into the straight phase was also fast. The fast skaters showed a larger maximum angle of extension of the knee joints than the relatively slow skaters, and the trunk ROM was smaller. Fast skaters tended to match the timing of the movement of the lower limb with the pelvis, while slow skaters tended to rotate the left pelvis backward. The velocity of the curve phase did not show a clear relationship with stroke time, average trunk angle, and lap time. Conclusion: It is important to skate close to the inner line, keep the trunk ROM below 10 degrees, extend the knee angle to over 160 degrees, and match the movement of the pelvis and lower limb to accelerate in the curve phase. The average velocity of the curves was fast for many athletes, but the competition rankings were low. Therefore, it is possible to improve the performance by optimizing the start technique, the running characteristics of the straight phase, and the physical factors.

• Korean Institute of Interior Design Journal
• /
• v.26 no.3
• /
• pp.45-54
• /
• 2017

A social phenomenon that occurs in a physical space is said to be a complex system. However, space syntax, which is commonly employed by researchers to identify such social phenomena, has various limitations in interpreting their complexity. On the other hand, agent-based modeling considers a variety of factors including the personality of the agent, objective-oriented work flows, estimation according to time flows and better prediction of space use through diverse parameters depending the situation, as well as the characteristics of the space. The agent-based method thus has the potentials to be developed as an alternative to space syntax techniques. In particular, discrete event driven simulation(DEVS), which is part of the agent-based modeling method, embraces the concept of networks just like space syntax, which allows a possible theoretical linkage in the future. This study suggests a procedural model of agent-based DEVS reflecting two different connection methods, i.e. connections between adjacent areas and those of the entire space, and attempts to identify the relationship between the local and regional indices of space syntax. A number of spaces were selected as examples-one for a preliminary experiment and eight modified for the main experiment-and space syntax and DEVS were applied to each of them. The comparative analysis of the results led to the conclusions as follows: 1) Adjacent connections were closely related to local indices, while the whole-space approach to regional indices. Local integration shows both characteristics. 2) Observation of the time flow model indicated a faster convergence with the range of 1 to 3-fold of the total time of one lap, with the error of less than 10%. 3) The heat map analysis showed more obvious characteristics of using the space for the entire space rather than adjacent connections. 4) Space syntax shows higher eligibility than ABM.

• Journal of Korean Society of Transportation
• /
• v.23 no.3 s.81
• /
• pp.137-147
• /
• 2005

This study is to define new road capacity concept, and to develop and propose an estimation method, through the analysis of individual vehicular behaviors in continuum flow. Developments in detection technology enable various and precise traffic data collection. The U.S. HCM (Highway Capacity Manual) method does not require such various and precise traffic data, and outputs only limited results. Alternative capacity concepts, which can be classified into a stochastic model and behavioral or deterministic model, are attempts for modeling some prominent traffic flow features, namely so-called a capacity drop and a traffic hysteresis, using such various and precise traffic data. Yet, no capacity concept up-to-date can describe both features. The analysis of individual vehicular behaviors, including speed-density plot per time lap, traffic flow-speed-density diagram per each sampling interval, time headway distribution, and free flow speed distribution, is performed for overcoming the limits of the previous capacity concepts. A stochastic methods are applied to determine time headway for estimating freeway capacity for traffic control.

• Journal of Adhesion and Interface
• /
• v.6 no.1
• /
• pp.1-6
• /
• 2005

The high accurate simulation of very thin glue layers based on the finite element method is still connected to many problems which result from the necessity to construct a complicated mesh of essentially different sizes of elements. This can lead to a loss of accuracy, unstable calculations and even loss of convergence. However, the implementation of special transmission elements along the glue ling and special edge-elements in the near-edge region would lead to a dramatic decrease of number of finite elements in the mesh and thus, prevent unsatisfactory phenomena in numerical analysis and extensive computation time. The theoretical basis for such special elements is the knowledge about appropriate transmission conditions and the edge effects near the free boundary of the adhesive layer. Therefore, recently proposed so-called non-classical transmission conditions and the behavior near the free edge are investigated in the context of the single-lap tensile-shear test of adhesive technology.

• The Bulletin of The Korean Astronomical Society
• /
• v.38 no.2
• /
• pp.95.2-95.2
• /
• 2013

The Van Allen Probes were designed to study the Earth's radiation belts on various scales of space and time. The identical two spacecrafts going nearly eccentric orbits lap each other several times over the course of the mission and each probe carries five instrument suites to address the science objectives on the radiation belt. Since Van Allen Probes launched on August 30, 2012, the probes detecte several storm events up to now. To understand the particle acceleration and loss mechanism in the radiation belt, we first focus on the energetic electrons' dynamics detected by ECT (Energetic Particle, Composition, and Thermal Plasma Suite). ECT measures near-Earth space's radiation particles covering the full electron and ion spectra from ~ eV to 10's of MeV with sufficient energy resolution. In this paper, we present the preliminary results of the recent several storm events using electron data from ECT(MagEIS and REPT).

• Structural Engineering and Mechanics
• /
• v.72 no.5
• /
• pp.557-568
• /
• 2019

Accurate modeling of contact interface in bolted joints is crucial in predicting the dynamic behavior for bolted assemblies under external load. This paper presents a contact pressure distribution based non-uniform virtual material method to describe the joint interface of assembly structure, which is connected by sparsely distributed multi-bolts. Firstly, the contact pressure distribution of bolted joints is obtained by the nonlinear static analysis in the finite element software ANSYS. The contact surface around bolt hole is divided into several sub-layers, and contact pressure in each sub-layer is thought to be evenly. Then, considering multi-asperity contact at the micro perspective, the relationship between contact pressure and interfacial virtual material parameters for each sub-layer is established by using the fractal contact theory. Finally, an experimental platform for the dynamic characteristics testing of a beam lap structure with double-bolted joint is constructed to validate the efficiency of proposed method. It is found that the theoretical results are in good agreement with experimental results by impact response in both time- and frequency-domain, and the relative errors of the first four natural frequencies are less than 1%. Furthermore, the presented model is used to examine the effect of rough contact surface on dynamic characteristics of bolted joint.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.9
• /
• pp.135-141
• /
• 2004

Anti-shock performance is one of the most important design specifications of TFT-LCD modules. Since they are adopted fur major display units of many mobile applications such as lap-top PCs, cellular phones, and palm pilots, they are able to accommodate and endure high level transient mechanical energy inputs. For the reasons, not only the LCD unit manufacturers but their customers like PC makers perform a series of strict impact/drop test on the units. Currently, designers are mostly relying on their own trial-error based experience for the anti-shock design. Thus those designs depending on only experience may result in disqualification from the drop/impact test during final product evaluation. Those shock failures of any new designs are prohibitive for both LCD and PC manufacturers. In order to avoid this problem, many designers are focusing on the development of computer-aided design tools that is directly connected to shock simulation capabilities and then shock-proof design cycle time could be significantly reduced. Development of an integrated CAE system for the shock-proof design is presented in this article. At every stages of the development of present work, practical industrial applicability and mass production feasibility are seriously considered and tested so that the system is to be used in the LCD design engineering field.

• International Journal of Precision Engineering and Manufacturing-Green Technology
• /
• v.5 no.5
• /
• pp.613-621
• /
• 2018

The electrically assisted brazing of a ferritic stainless steel with nickel-based filler metal is experimentally investigated. During electrically assisted brazing of a lap joint, the temperature of the joint is first rapidly increased to a brazing temperature and held nearly constant for a specific period using a pulsed electric current. Microstructural analysis results strongly suggest that the electric current during electrically assisted brazing enhances diffusion between the filler metal and the ferritic stainless steel, thus inducing significantly thicker diffusion zones compared with induction brazing. The mechanical test results show that the strength of the electrically assisted brazing joint is comparable to or even superior to those of the joint fabricated by induction brazing, while the process time of the electrically assisted brazing is significantly shorter than that of induction brazing.

• Journal of Gastric Cancer
• /
• v.19 no.2
• /
• pp.193-201
• /
• 2019

Purpose: There is no consensus on the optimal method for intracorporeal esophagojejunostomy (EJ) in laparoscopic total gastrectomy (LTG). This study aims to compare 2 established methods of EJ anastomosis in LTG. Materials and Methods: A total of 314 patients diagnosed with gastric cancer that underwent LTG in the period from January 2013 to October 2016 were enrolled in the study. In 254 patients, the circular stapler with purse-string "Lap-Jack" method was used, and in the other 60 patients the linear stapling method was used for EJ anastomosis. After propensity score matching, 58 were matched 1:1, and retrospective data for patient characteristics, surgical outcome, and post-operative complications was reviewed. Results: The 2 groups showed no significant difference in age, body mass index, or other clinicopathological characteristics. After propensity score matching analysis, the linear group had shorter operating time than the circular group ($200.3{\pm}62.0$ vs. $244.0{\pm}65.5$, $P{\leq}0.001$). Early postoperative complications in the circular and linear groups occurred in 12 (20.7%) and 15 (25.9%, P=0.660) patients, respectively. EJ leakage occurred in 3 (5.2%) patients from each group, with 1 patient from each group needing intervention of Clavien-Dindo grade III or more. Late complications were observed in 3 (5.1%) patients from the linear group only, including 1 EJ anastomosis stricture, but there was no statistical significance. Conclusions: Both circular and linear stapling techniques are feasible and safe in performing intracorporeal EJ anastomosis during LTG. The linear group had shorter operative time, but there was no difference in anastomosis complications.

• International Journal of Automotive Technology
• /
• v.5 no.1
• /
• pp.55-59
• /
• 2004

Spot welding is a very important and useful technology in fabrication of thin sheet structures such as the parts in an automobile. However, because the fatigue strength of the spot welding point is considerably lower than that of the base metal due to stress concentration at the nugget edge, the nugget size must be estimated to evaluate a reasonable fatigue strength at a spot welded lap joint. So far, many investigators have experimentally studied the estimation of fatigue strengths of various spot weldments by using a destructive method. However, these destructive methods poses problems so testing of weldments by these methods are difficult. Furthermore, these methods cannot be applied to a real product, and are time and cost consuming, as well. Therefore, there has been a strong, continual demand for the development of a nondestructive method for estimating nugget size. In this study, the effective nugget size in spot weldments have been analyzed by using thermoelastic stress analysis adopting infrared thermography. Using the results of the temperature distribution obtained by analysis of the infared stress due to adiabatic heat expansion under sinusoidal wave stresses, the effective nugget size in spot welded specimens were estimated. To examine the evaluated effective nugget size in spot weldments, it was compared with the results of microstructure observation from a 5％ Nital etching test.