• Journal of Chest Surgery
• /
• 제23권1호
• /
• pp.22-32
• /
• 1990

Postoperative cardiac performance of cyanotic congenital heart disease is somewhat different from that of other cardiac diseases. For the evaluation of postoperative cardiac performance in the cyanotic congenital heart disease we measured cardiac output by thermodilution technique at 1, 4, 8, 12, 16, 20, 24, 36, 48 postoperative hours in 14 patients operated from Feb. 1989 to Nov. 1989 in The Department of Thoracic and Cardiovascular Surgery, Seoul National University Children`s Hospital. At the same time, we checked left atrial pressure [LAP], central venous pressure [CUP], and mixed venous oxygen saturation [SvO2] to detect correlation between them. Immediate postoperative cardiac index was 3.585 $\pm$ 0.945 L/min/m2, and it decreased maximally to 3.322$\pm$1.007 L/min/m2 at postoperative 16 hours. After then it increased and stabilized from 36 hours after operation, and its value was 4.426$\pm$1.358 L/min/m2. There were no correlations between cardiac index and left atrial pressure or central venous pressure. Between mixed venous oxygen saturation and cardiac index, there was no correlation in the early postoperative period but after postoperative 16 hours, there was significant correlation between them and correlation coefficients were 0.573 [16hrs], 0.743 [20hrs], 0.436 [24hrs], 0.560 [36hrs], 0.636 [48hrs], respectively. From these results, we concluded that in the corrective surgery of cyanotic congenital heart disease, cardiac performance was depressed in the early postoperative period. It improved from postoperative 16 hours, and stabilized from 36 hours after operation. During early postoperative period, mixed venous oxygen saturation should not be used as a predictor of cardiac performance but it could be used as a predictor of cardiac performance from 16 hours after operation.

• International Journal of Concrete Structures and Materials
• /
• 제9권3호
• /
• pp.345-367
• /
• 2015

Past earthquakes have signaled the increased collapse vulnerability of mainshock-damaged bridge piers and urgent need of repair interventions prior to subsequent cascading hazard events, such as aftershocks, triggered by the mainshock (MS). The overarching goal of this study is to quantify the collapse vulnerability of mainshock-damaged substandard RC bridge piers rehabilitated with different repair jackets (FRP, conventional thick steel and hybrid jacket) under aftershock (AS) attacks of various intensities. The efficacy of repair jackets on post-MS resilience of repaired bridges is quantified for a prototype two-span single-column bridge bent with lap-splice deficiency at column-footing interface. Extensive number of incremental dynamic time history analyses on numerical finite element bridge models with deteriorating properties under back-to-back MS-AS sequences were utilized to evaluate the efficacy of different repair jackets on the post-repair behavior of RC bridges subjected to AS attacks. Results indicate the dramatic impact of repair jacket application on post-MS resilience of damaged bridge piers-up to 45.5 % increase of structural collapse capacity-subjected to aftershocks of multiple intensities. Besides, the efficacy of repair jackets is found to be proportionate to the intensity of AS attacks. Moreover, the steel jacket exhibited to be the most vulnerable repair intervention compared to CFRP, irrespective of the seismic sequence (severe MS-severe or moderate AS) or earthquake type (near-fault or far-fault).

• 폴리머
• /
• 제25권1호
• /
• pp.49-55
• /
• 2001

비닐계 단량체인 아크릴로니트릴과 스티렌을 E-beam 전조사법에 의해 폴리프로필렌 섬유에 그라프트 반응시켜 PP-g-(AN/St) 공중합체를 제조한 후 아미드옥심기와 슬폰기를 도입하여 이관능성 이온교환섬유를 제조하였다. 그라프트율은 단량체 내에 아크릴로니트릴의 조성이 감소할수록 증가하였으며 최대 101.1%이었고 최대 아미드옥심화율은 7.2 mmol/g이었다. 또한 섬유상 이온교환체의 초기 열분해 온도는 120 ${\circ}C$ 이었고 함수율은 공중합체 내에 아미드옥심화율이 증가할수록 감소하였고 슬폰화율이 증가할수록 증가하는 경향을 나타냈다. APP-g-AN, SPP-g-St, ASPP-g-(AN/St) 이온교환체의 우라늄 흡착량은 각각 12.4, 34, 38mg/g이었으며 최적 흡착시간은 약 50시간이었다. 우라늄 흡착 실험결과, 본 실험에서 합성한 이온교환체 ASPP-g-(AN/St)는 $UO_2^{2+}$에 대하여 우수한 성능을 보였다.

• Composites Research
• /
• 제30권6호
• /
• pp.416-421
• /
• 2017

CFRP와 금속간의 접합공정이 개선된 구조용 접착제가 제조되었다. 구조용 접착제에 대한 경화시간, 기지재료의 표면상태 그리고 접착제의 양에 따른 최적의 접합공정 조건을 랩쉐어 실험을 통하여 파악하였다. 적합한 접합조건을 확인하기 위해 이종재료간의 접합 파단면 상태를 반사현미경을 이용하여 평가하였다. 이종재료간 접합력 향상을 위해 접착제의 개선뿐만 아니라 CFRP의 표면처리 또한 중요하였다. 구조용 접착제의 경우 180도 조건에 20분의 경화온도 조건이 최적이였으며, CFRP의 표면 처리에 따라 접합특성이 향상됨을 확인하였다. 이종재료 간 접합을 위해 구조용 접착제의 양은 $1.5{\times}10^{-3}g/mm^2$ 조건일 때 최적이었다. 접합공정의 개선 및 최적화를 통해 기존의 접착력 대비 10% 이상의 물성 강화를 나타냄을 확인하였다.

• International Journal of Automotive Technology
• /
• 제5권1호
• /
• pp.55-59
• /
• 2004

Spot welding is a very important and useful technology in fabrication of thin sheet structures such as the parts in an automobile. However, because the fatigue strength of the spot welding point is considerably lower than that of the base metal due to stress concentration at the nugget edge, the nugget size must be estimated to evaluate a reasonable fatigue strength at a spot welded lap joint. So far, many investigators have experimentally studied the estimation of fatigue strengths of various spot weldments by using a destructive method. However, these destructive methods poses problems so testing of weldments by these methods are difficult. Furthermore, these methods cannot be applied to a real product, and are time and cost consuming, as well. Therefore, there has been a strong, continual demand for the development of a nondestructive method for estimating nugget size. In this study, the effective nugget size in spot weldments have been analyzed by using thermoelastic stress analysis adopting infrared thermography. Using the results of the temperature distribution obtained by analysis of the infared stress due to adiabatic heat expansion under sinusoidal wave stresses, the effective nugget size in spot welded specimens were estimated. To examine the evaluated effective nugget size in spot weldments, it was compared with the results of microstructure observation from a 5％ Nital etching test.

• 접착 및 계면
• /
• 제5권2호
• /
• pp.22-36
• /
• 2004

Several in-situ testing methods of adhesively bonded joints under static short-time tensile loading are critically analyzed in terms of experimental procedure and data evaluation. Due to its rather homogeneous stress state across the glue line, the tensile-shear test with thick single-lap specimens, according to ISO 11003-2, has become the most important test process for the determination of realistic materials parameters. This basic method, which was improved in both, the experimental part by stepped adherends and easily attachable extensometers and the evaluation procedure by numeric substrate deformation correction and test simulation based on the finite element method (FEM), is therefore demonstrated by application to several kinds of adhesives and metallic adherends. Multi-axial load decreases the strength of a joint. This effect, which is illustrated by an experimental comparison, impedes the derivation of realistic mechanical characteristics from measured force-displacement curves. It is shown by numeric modeling that tensile-shear tests with thin plate substrates according to ISO 4587, which are widely used for quick industrial quality assurance, reveal an inhomogeneous stress state, especially because of relatively large adherend deformation. Complete experimental determination of the elastic properties of bonded joints requires independent measurement of at least two characteristics. As the thick-adherend tensile-shear test directly yields the shear modulus, the tensile butt-joint test according to ISO 6922 represents the most obvious complement of the test programme. Thus, validity of analytical correction formulae proposed in literature for the derivation of realistic materials characteristics is verified by numeric simulation. Moreover, the influence of the substrate deformation is examined and a FEM correction method introduced.

• 한국게임학회 논문지
• /
• 제15권4호
• /
• pp.169-178
• /
• 2015

다양한 수준의 게임 난이도를 사용자에게 제공하는 것은 게임 개발 시 주요 고려 사항 중 하나이다. 본 논문에서는 1인용 자동차 주행 게임에서 주어진 난이도를 갖도록 주행 트랙에 도전들을 배치하는 방법을 제안한다. 여기서 도전은 자동차 주행을 방해하는 장애물을 말하고, 게임 난이도는 트랙 한 바퀴를 도는데 필요한 예상 주행 시간으로 나타낼 수 있다. 제안된 방법에서는 도전 배치 문제를 IP(Integer Programming) 문제로 모델링한 후, LP 완화 및 시뮬레이티드 어닐링 방법으로 해를 구한다. 실험 결과, 주어진 목표 시간에 맞는 주행 시간을 갖는 도전 배치를 구할 수 있었다. 이들 도전 배치를 트랙에 적용한 후 시험 주행해 봄으로써, 실제 주행 시간은 평균적으로 해당 도전 배치의 목표 시간과 일치함을 보였다. 제안된 방법은 사용자에게 다양한 난이도의 게임 플레이를 제공함으로써, 게임의 흥미와 몰입감을 높일 것이다.

• Steel and Composite Structures
• /
• 제38권1호
• /
• pp.87-102
• /
• 2021

To investigate the failure form, bending stiffness, and residual bearing capacity of monolithic composite beams with laminated slab throughout the fire process, fire tests of four monolithic composite beams with laminated slab were performed under constant load and temperature increase. Different factors such as post-pouring layer thickness, lap length of the prefabricated bottom slab, and stud spacing were considered in the fire test. The test results demonstrate that, under the same fire time and external load, the post-pouring layer thickness and stud spacing are important parameters that affect the fire resistance of monolithic composite beams with laminated slab. Similarly, the post-pouring layer thickness and stud spacing are the predominant factors affecting the bending stiffness of monolithic composite beams with laminated slab after fire exposure. The failure forms of monolithic composite beams with laminated slab after the fire are approximately the same as those at room temperature. In both cases, the beams underwent bending failure. However, after exposure to the high-temperature fire, cracks appeared earlier in the monolithic composite beams with laminated slab, and both the residual bearing capacity and bending stiffness were reduced by varying degrees. In this test, the bending bearing capacity and ductility of monolithic composite beams with laminated slab after fire exposure were reduced by 23.3% and 55.4%, respectively, compared with those tested at room temperature. Calculation methods for the residual bearing capacity and bending stiffness of monolithic composite beams with laminated slab in and after the fire are proposed, which demonstrated good accuracy.

• 대한소아치과학회지
• /
• 제26권3호
• /
• pp.554-563
• /
• 1999

심미적 수복재료인 복합 레진과 글래스 아이오노머 시멘트는 중합방식에 따라 화학중합형, 광중합형, 그리고 이 두 가지 중합방식을 겸비한 이중중합형으로 분류할 수 있다. 화학중합형과 광중합형에 대해서는 지금까지 다수의 보고가 있었으나, 충전용 복합 레진의 경우 이들과 이중중합형을 비교한 예는 아직 찾기 힘든 실정이었으므로, 이러한 관점에서의 연구가 필요할 것으로 사료되었다. 이 연구에서는 이중중합 수복재가 단일중합방식에 비해 어떠한 특성을 보이는지를 탐구하고자 하였다. 사용된 재료는 광중합형 복합 레진인 Veridonfil-Photo와 이중중합형인 Bis-core, 이중중합형의 글래스 아이오노머 시멘트인 Fuji II LC와 화학중합형인 Ketac-fil을 사용하였다. 가로 30mm, 세로 30mm, 높이 1mm와 3mm인 두 종류의 아크릴릭 몰드 중앙에 직경 7mm의 hole을 형성하여 여기에 4종의 수복재를 충전하였다. 충전 직후부터 시작하여 24시간 경과시까지 일정 시간의 간격으로 표면, 1mm, 3mm 깊이에서의 경도를 미세경도계(Shimadzu Micro Hardness Tester HMV-2000, Shimadzu Co. Japan)로 측정하였다. 측정치를 통계처리하여 얻은 결과는 다음과 같다. 1. 4 종의 수복재 모두에서, 중합직후에 비해 24시간 경과후의 미세경도가 증가되었다. 2. 중합 직후부터 24시간 경과시점까지의 미세경도를 측정한 결과, Ketac-fil을 제외한 나머지 수복재에서는 각 깊이간 경도의 차이가 있었다. 3. 각 수복제의 최종중합에 도달하는 시간을 조사한 결과, 이중중합형이 3min의 깊이에서 광중합형이나 화학중합형에 비해 중합이 더 오래 지속된 것으로 나타났다. 이상의 결과에서 조사광이 충분히 도달하지 못하여 중합이 현저히 떨어지는 수복재의 심부에도 이중중합방식을 사용할 경우에는 지속적인 중합반응이 일어나 중합도가 증가하는 것으로 나타났다.

• 대한치과보철학회지
• /
• 제41권6호
• /
• pp.732-746
• /
• 2003

Statement of problem. Soft lining materials, also referred to as tissue conditioning materials, tissue heating materials, relining materials, soft liners or tissue conditioners, were first introduced to dentistry by a plastic manufacturer in 1959. Since the introduction of the materials to the dental field, their material properties have been continually improved through the effort of many researchers. Soft lining materials have become widely accepted, particularly by prosthodontists, because of their numerous clinical advantages and ease of manipulation. Unfortunately, few reports have been issued upon the topic of increasing the bond strength between the base metal alloy used in cast denture bases and PMMA soft liner modified with 4-META, nor upon the pattern of debonding and material change in wet environment like a intra oral situation. Purpose. The purposes of this study were comparing the bond strength between base metal alloy used for the cast denture bases and PMMA soft liner modified with 4-META, and describing the pattern of debonding and material property change in wet environment like the intraoral situation. Material and Methods. This study consisted of four experiments: 1. The in vitro measurement of shear bond strength of the adhesive soft liner. 2. The in vitro measurement of shear bond strength of the adhesive soft liner after 2 weeks of aging. 3. A comparison of debonding patterns. 4. An evaluation the Relation time of modified soft liner. The soft liner used in this study was commercially available as Coe-soft (GC America.IL.,USA), which is provided in forms of powder and liquid. This is a PMMA soft liner commonly used in dental clinics. The metal primer used in this study was 4-META containing primer packed in Meta fast denture base resin (Sun Medical Co., Osaka, Japan). The specimens were formed in a single lap joint desist which is useful for evaluating the apparent shear bond strength of adhesively bonded metal plate by tensile loading. Using the $20{\times}20mm$ transparent grid, percent area of adhesive soft liner remaining on the shear area was calculated to classify the debonding patterns. To evaluate the change of the initial flow of the modified adhesive soft liner, the gelation time was measured with an oscillating rheometer (Haake RS150W/ TC50, Haake Co., Germany). It was a stress control and parallel plate type with the diameter of 35mm. Conclusion. Within the conditions and limitations of this study, the following conclusions were drawn as follows. 1. There was significant increase of bond strength in the 5% 4-META, 10% 4-META containing groups and in the primer coated groups versus the control group(P<0.05). 2. After 2 weeks of aging, no significant increase in bond strength was found except for the group containing 10% 4-META (P<0.05). 3. The gelation times of the modified soft liner were 9.3 minutes for the 5% 4-META containing liner and 11.5 minutes for the 10% 4-META liner. 4. The debonding patterns of the 4-META containing group after 2 weeks of aging were similar to those of immediaely after preparation, but the debonding pattern of the primer group showed more adhesive failure after 2 weeks of aging.