• Journal of the Korean Vacuum Society
• /
• v.14 no.1
• /
• pp.49-57
• /
• 2005

The characteristics of current and voltage in a basic discharge experiment are investigated for a cold cathode fluorescent lamp with ballast capacitors attached at both ends of lamp and for a capacitive coupled external electrode fluorescent lamp. In the current-voltage characteristics for a cold cathode fluorescent lamp except ballast capacitors, it is shown that the typical glow discharge with the cathode fall follows after the dark current and Townsend firing discharge. However, in the characteristics for a cold cathode fluorescent lamp including ballast capacitors, the current increases as the voltage increases in the glow discharge region without representing a cathode fall since the most voltage is loaded at two capacitors. The characteristics for the external electrode fluorescent lamp shows the same as that of the cold cathode fluorescent lamp in the respect of glow discharge characters, and the external electrode itself roles the ballast capacitor.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.5
• /
• pp.430-436
• /
• 2008

This paper proposes a way to predict electrical lifetime of a relay using Accelerated Life Testings (ALTs). The relay of interest mounting on printed circuit boards is usually under an inrush current stress. The inrush current is generated and accelerated through controlling a lamp switching device in the ALT. We find that the dominant failure mechanism under high levels of inrush current would be contact welding in the contact surface of the relay and the contact welding process is accelerated according to increase in inrush current. The electrical lifetime model based on Inverse Power Law in term of inrush current is proposed, and parameters characterizing relay's lifetime distribution are statistically estimated using ALTA 6 PRO software.

• International Journal of Computer Science & Network Security
• /
• v.22 no.1
• /
• pp.175-182
• /
• 2022

This work presents a simulation model for a specific UV disinfection system (UVDS) powered by a Photovoltaic System. The global UVDS also includes the electronic converters, Electronic Ballast, UV Lamp and Motor Pump. The equations that model the physical components' behaviour are connected to obtain a dynamic global model. The latter is converted in a Simulink/Matlab model, which allows to carry out simulation series concerning the entire UVDS. The physical parameters: the irradiation G and the temperature T, are considered as inputs. series of measurements carried out in order to show how these parameters affect the current, the voltage of the PVs and especially the value of the current of the UV lamp, on the other hand a study on the behavior and the evolution of the parameters of the motor pump such as the armature current, motor torque, speed of rotation and the water flow. The purpose of all this is to realize how important are the two parameters concerning the lamp current and the water flow because they are two very important factors to keep an adequate water quality.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.4
• /
• pp.652-658
• /
• 2006

This paper deals with an electronic ballast for hish intensity short-arc discharge lamps, which consists of a boost converter, a step down converter operated as a current source with power regulation and a low frequency inverter with external ignition circuit The ignition circuit generates high voltage pulses of 130[Hz] up to 5 [kV]. A reignition circuit is equipped in the ballast, and it operates the lamp at a regular interval for protection when an ignition fails. Acoustic resonance phenomenon was eliminated by operating a low frequency square wave voltage and current. The measured lamp voltage, current and consumption power were 123.8 [V], 8.1 [A] and 1,002 [W], respectively. From the experiment, we confirmed that the prototype ballast operates the lamp with a constant power.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.10
• /
• pp.530-535
• /
• 2001

Resonant-type electronic ballast for a metal halide discharge(MHD) lamp is proposed and implemented for 400W MHD lamp. HID lamps have good color rendition, long life and good focusing capability but they have flickers by acoustic resonance when driven at high frequency. A new control method is employed to remove acoustic resonance related instability in HID lamp. By using the amplitude modulation, a spread spectrum effect is employed on the ballast. The control loop of resonant inverter is analyzed and a current is designed. The ballast consists of a power factor controller, an half-bridge resonant inverter, a simple ignitor and an integrator with OP-amps. The experimental results show the good performance as PF 0.93, ballast loss 22W at output 400W and the conducted EMI level is below 60dBuV.

• Journal of Industrial Technology
• /
• v.31 no.B
• /
• pp.67-73
• /
• 2011

Ceramic metal halide lamps have been widely used due to long lifetime, high luminous efficiency and good colour rendering. In this paper, we developed dimming control system of electronic ballast for 70W ceramic metal halide lamp by using 1-10V interface. The proposed electronic ballast is consists of EMI filter, Full-wave rectifier, Active PFC, DBI(Dual Buck Inverter), Igniter and control circuit.It enables to supply both low-frequency rectangular wave voltage and current to the lamp by using DBI(Dual Bcuk Inverter) structure. By using 1-10V interface, the system that able to dimming the lamp is demonstrated by P-spice simulation and experimental results.

• Journal of Industrial Technology
• /
• v.29 no.B
• /
• pp.133-137
• /
• 2009

This paper presents the development of smart road line lamp system consisting light control device. It can perform the individual power control or partial on/off control of a LED lamp by control center and can detect the error of the LEDs by current sensing. Also, the ability to control the brightness and period of on/off by detecting the car's existence. This light control circuit consists of road line lamp unit device. It can give a lot of solutions when the server, which controls the whole system, is operated through CDMA(Code-Division Multiple Access) network.

• Current Optics and Photonics
• /
• v.1 no.3
• /
• pp.233-238
• /
• 2017

In this paper we propose a freeform secondary lens for an LED fishing/working lamp (LFWL). This innovative LED lamp is used to replace the traditional HID fishing lamp, to satisfy the lighting demands of fishing and the on-board activities on fishing boats. To realize the freeform lens's geometry, Gaussian decomposition is involved in our optics-design process for approaching the targeted light intensity distribution curve (LIDC) of the LFWL lens. The simulated results show that the illumination on the deck, on the sea's surface, and underwater shows only small differences between LED fishing/working lamps and HID fishing lamps. Meanwhile, a lighting efficiency of 91% with just one third of the power consumption can be achieved, when the proposed LED fishing/working lamps are used instead of HID fishing lamps.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1259-1264
• /
• 2008

This paper presents an accelerated life test for burn out of tungsten filament of automotive halogen lamp. There are many failure modes and failure factors that associated with tungsten filament. But in this explain the dominant failure mode of tungsten filament is the bumout of the filament failure. At first, over voltage, high temperature, inrush current and vibration are selected as stress factors by using of two stage Quality Function Deploymeng(QFD). And we planed accelerated life test that has one factor(voltage) and three levels. By experiment it has absorbed that over voltage has an effect on the life of halogen lamp. Using ALTA programs, we estimated the common shpae parament of Weibull distribution, life-stress relationship and $B_{100p}$ life.

• Proceedings of the KIEE Conference
• /
• 2001.10a
• /
• pp.208-211
• /
• 2001

This paper presents the considerations of the high frequency modulation method for the metal halide lamp electronic ballast. The acousitc resonance phenomenon is occurred, if the metal halide lamp is driven at constant high frequency. The frequency modulation method therefore, is used to avoid the acoustic resonance phenomenon, but the crest factor of lamp current is increased. In this paper, the driving characteristic of the metal halide lamp according to the waveshape and frequency variations of modulating signal is considered with a viewpoint of crest factor.