• Tunnel and Underground Space
• /
• v.16 no.6 s.65
• /
• pp.476-485
• /
• 2006

During blasting, both shock wave and gas are generated in detonation process of explosives and the generated wave and gas expansion may create new fractures and damage rock mass. In order to explain and understand completely the fracture mechanism by blasting, we have to consider both effects of the wave and gas expansion simultaneously. In this study, we use a discrete element code, PFC2D and develop an algorithm which is capable of modeling both detonation and gas pressures acting on blasthole wall and visualizing generated cracks within rock mass. Moreover, the gas-pressure modeling method which applies a corresponding external force of gas pressure to parent particles of radial fractures is adopted to simulate a coopting between rock mass and gas penetrating created radial fractures. The developed algorithm is verified by reproducing numerical simulations of a lab-scale test blast successfully.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.5
• /
• pp.531-538
• /
• 2007

The effects of temperature, coagulants and pre-chlorination on the removal of turbidity and pathogenic protozoa by coagulation process were investigated using jar test of lab scale. In room temperature ($25^{\circ}C$), protozoa were removed over 1.0log at the proper concentration range of coagulants, and up to over 2log at the optimal concentration of coagulants. Considering the 1.5log target removal for Giardiain the processes of coagulation, sedimentation, and filtration, this results implies that the target could be satisfied. However, the removal of protozoa and turbidity was reduced, and optimal PAC concentration was narrowed in low turbidity and cold temperature ($5^{\circ}C$). These results suggest that the drop of coagulation efficiency may be occurred in winter if the conditions are not optimized. Despite the effect of water temperature, the relation of turbidity and protozoa removal appeared to be good. The various kinds of coagulants did not significantly affected for removals of turbidity and protozoa when the concentrations of $Al_2O_3$ were considered. Prechlorination did not increase or decrease the removal of turbidity and protozoa in optimum condition at room temperature, pH 7, 15mg/L of PAC concentration.

• Journal of Korean Society of Water and Wastewater
• /
• v.21 no.5
• /
• pp.521-529
• /
• 2007

Nutrient removal from synthetic wastewater was investigated using a MLE (Modified-Ludzack Ettinger) type MBBR (Moving Bed Biofilm Reactor), with different phenol ($C_6H_5OH$) concentrations, in order to determine the inhibition effects of phenol on biological nutrient removal and the biodegradation of phenolic wastewater. The wastewater was prepared by mixing a solution of molasses with known amounts of phenol and nutrients. The experiments were conducted in a lab-scale MLE type MBBR, operated with four different phenol concentrations (0, 67, 100 and 168mg/L) in the synthetic feed. Throughout the experiments, the ratio of the phenolic COD concentration to the total COD was varied from 0 to 1. Throughout batch test, the SNR (Specific Nitrification Rate) and SDNR (Specific Denitrification Rate) were significantly influenced by changes of the phenol concentration. Phenol was inhibitory to the nitrification/denitrification process, and showed greater inhibition with higher initial phenol concentrations. The SNR observed with 0, 67, 100 and 168mg phenol/L were very different like 10.12, 6.95, 1.51 and $0.35mg\;NH_{3^-}N/gMLVSS$ hr, respectively. Similarly, the SDNR observed at 0, 67, 100 and 168mg phenol/L were different like 0.322, 0.143, 0.049and 0.006mgN/gMLVSS day, respectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.985-990
• /
• 2003

In order to demonstrate Advanced Spent Fuel Conditioning Process (ACP), shielding facilities such as hot cell suitable to handling radionuclides and process property will be necessary. But the construction of new facilities needs much money, man-power and time, it is now scheduled to remodel the hot cell, which has already been installed and maintained at Irradiated Material Experiment Facility (IMEF) in the Korea Atomic Energy Research Institute (KAERI). The basic structure and concrete shield wall of hot cell partly have been constructed on the base floor in IMEF building in current status. And hot cell after remodeling will be used for carrying out the lab-scale experiment of ACP. The hot cell was built in accordance with 35 curies of fe-59(1.2 MeV) as design criteria of radiation dose limit. But the radioactive source of ACP is expected to be much higher than design criteria of IMEF, shielding ability of the hot cell in the current status is unsatisfactory to the hot test of ACP. Therefore shield wall shall be reinforced with heavy concrete, steel or lead. In this paper, dose rates are calculated according to ACP source, shielding materials, etc., and reinforcement structures are determined considering the current situation of hot cells, installation of shield windows and the easiness of work.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.4
• /
• pp.364-369
• /
• 2005

An experimental study was conducted on the thermal conductivity of various grouting materials for geothermal heat exchanger which is used as a heat sink or source in the heat pump system. The grouting of the vertical heat exchanger is important for environmental and heat transfer reasons and is generally accomplished by the placement of a low permeability material into the annular space between the borehole wall and the pipes suspended in the borehole. In this study, a lab scale test apparatus was made and measured the thermal conductivity of four grouting materials. As a result, the temperature rising tendency was similar among them, but the increasing rate was different. Thus the thermal conductivity showed a maximum difference of $27\%$ among grouting materials.

• Journal of Korean Society of Water and Wastewater
• /
• v.30 no.5
• /
• pp.545-551
• /
• 2016

This study compares characteristic of membrane fouling in MBR-RO systems. In lab. scale MBRs test, MBRs were operated at different Flux(10, 20, 30 & 40 LMH) and temperature(10, 15, 20, 25 & $30^{\circ}C$). The results show that MBR permeate was measured lower amounts of organic substances in Higher flux and lower temperature and led to lower RO fouling rates. The main cause was that due to cake fouling formed on membrane surfaces in MBRs. Under both cases, Cake layer of membrane surfaces formed in MBRs removed RO fouling factors, polysaccharide and protein, because of cake layer attached on membrane surfaces greater amounts of organic substances. This study implies that optimization of MBR with operating conditions is a crucial strategy to RO membrane fouling control.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.6_spc
• /
• pp.714-720
• /
• 2016

Rubbing and misalignment are the most usual faults that occurs in rotating machinery and with them severe effect on power plant availability. Especially blade rubbing is hard to detect on FFT spectrum using the vibration signal. In this paper, the possibility of feature analysis of vibration signal is confirmed under blade rubbing and misalignment condition. And the lab-scale rotor test device provides the blade rubbing and shaft misalignment modes. Feature selection based on GA (genetic algorithm) is processed by the extracted feature of the time domain. Then, classification of the features is analyzed by using SVM (support vector machine) which is one of the machine learning algorithm. The results of features selection based on GA compared with those based on PCA (principal component analysis). According to the results, the possibility of feature analysis is confirmed. Therefore, blade rubbing and shaft misalignment can be diagnosed by feature of vibration signal.

• Proceedings of the Korean Society of Life Science Conference
• /
• 2001.06a
• /
• pp.53-66
• /
• 2001

본 실험실에서는 혈당강하효과를 갖는 chiroinositol을 다량 함유하고 있는 식품이나 식용물질을 탐색하여 선발하고, 선택된 식품이나 식용물질에서 chiroinositol을 lab-scale로 분리 정제하여 제조된 chiroinositol의 추출물로 동물실험을 실시하여 혈당강하효과를 증명하고 그 기작을 연구하고 있다. 약 300여종의 식품 및 식용물질을 GC-MS 및 HPLC로 분석한 결과 식품으로 안전한 탈지대두와 두부 순물에서 chiroinositol의 함량이 각각 6.45mg/g, 20mg/g으로 조사되어 선택되었고, chiroinositol의 순도가 40-60%(w/w)인 chiroinositol의 추출물을 이용하여 동물실험을 통한 혈당강하효과를 조사한 결과, 1) steptozotocin(STZ)으로 유발된 고혈당쥐에 경구투여시, 농도 의존적으로 혈당을 감소시키는 탁월한 기능을 나타내었고, 2) 정상쥐의 혈당제거율 검사(glucose tolerance test)에서강한 제거율 및 6시간의 지속시간을 나타내었으며, 3) STZ로 유발된 고혈당쥐의 혈당제거율 검사에서 강한 혈당강하 효과(약 40%)를 나타내었으며 지속시간은 약 12시간이었다. 4) 극심한 고혈당(450 내지 500mg/d)의 경우, 경미한 고혈당(300내지 350mg/d)의 경우보다 혈당 감소율이 20% 가량 높았으며, 지속시간도 1시간 이상 긴 것으로 나타났으며, 5) 인슐린과 복합처리 했을 때 상승작용(synergy)을 나타내었으며, 저혈당증으로 전혀 발전되지 않았다.

• Journal of Ocean Engineering and Technology
• /
• v.33 no.6
• /
• pp.597-606
• /
• 2019

Due to climate change, coastal areas are being flooded with torrential rain, typhoons, and tsunamis. In addition, non-point source pollutants (NPSs) that accumulated on the ground, streets, and buildings during the dry season are washed off by rain and stormwater runoff, which adds to the damage associated with environmental pollution, e.g., pollution that makes its way into the ocean. Recently, low impact development (LID) has been considered as a means of controlling water circulation and NPSs. In the coastal area, permeable blocks have been constructed mainly to reduce the flood damage caused by waves. Some important design factors that must be considered to ensure long-term performance are the permeability coefficient, clogging, and the efficiency of the removal of total suspended solids (TSS), but currently there are no standardized design criteria or testing techniques that are used worldwide. Herein, we analyzed the permeability coefficient and the TSS removal efficiency tendency according to the permeability area ratio with an easily-detachable, permeable block filled with calcinated yellow soils as the filter media. Our lab-scale tests indicated that, when the permeability area ratio was 25%, the reduction of the permeability coefficient after clogged was 11%, which was a significant decrease compared to other cases. Permeability persistence increased when the permeability area ratio increased from 50% to 75%. The TSS removal efficiency decreased as the permeability area ratio increased. Our pilot-scale test indicated that the TSS removal efficiency was more than 80% higher in all cases. We also found that the permeability persistence was excellent as the permeability area ratio increased, and, in actual construction, it is effective to set 5.3% of the total area as permeable area in terms of permeability and economic feasibility.

• Journal of Korean Society on Water Environment
• /
• v.21 no.1
• /
• pp.7-13
• /
• 2005

With the appearance of pathogenic microorganisms, which were resistant to free chlorine, the significant attention to the necessity of powerful alternative disinfection methods such as ozone, chlorine dioxide, LTV irradiation to inactivating pathogens has been increased in water treatment. Among these alternative disinfection methods, ozone is well known as strong biocidal method and the usage of ozone is also increasing in Korea. However, in Korea, there has been no report on the quantitative study of Cryptosporidium parvum with ozone and its evaluation in advanced drinking water treatments. This study reports on the methodology for predicting the ozone inactivation of Cryptosporidium parvum by ozone disinfection in advanced drinking water treatment. The method is based on the fact that a specific inactivation level of microorganisms is achieved at a unique value of ozone exposures, independent of ozone dose and type of water, and quantitatively described by a delayed Chick-Watson model. The required values ${\bar{C}}T$ for 2 log inactivation of Cryptosporidium parvum was $6.0mg/L{\cdot}min$ and $15.5mg/L{\cdot}min$ at $20^{\circ}C$ and $5^{\circ}C$, respectively. From this obtained Cryptosporidium parvum inactivation curves and calculated ${\bar{C}}T$ values of advanced drinking water treatment water in Korea with FIA (Flow injection alaysis), we can predict that water treatment plant can achieve a 1.1~1.8 log inactivation and 0~0.4 log inactivation at $20^{\circ}C$ and $5^{\circ}C$, respectively. This methodology will be useful for drinking water treatment plants which intend to evaluate the disinfection efficiencies of their ozonation process without full scale test and direct experiments with Cryptosporidium parvum.