• Composites Research
• /
• 제21권5호
• /
• pp.15-22
• /
• 2008

본 논문은 샌드위치 복합재가 적용된 자동무인경전철 차체 구조물의 구조 안전성 및 충돌 안전성 결과에 대해 서술하고 있다. 차체 구조물에 적용된 샌드위치 복합재는 알루미늄 하니컴 심재와 WR580/NF4000 유리섬유/에폭시 적층 복합재 면재로 이루어져 있다. 차체 구조물에 적용되는 적층 복합재 면재에 대해 기계적 시험을 통하여 물성을 획득하였고, 직교 이방성 특성을 갖는 하니컴 심재의 물성은 유효등가손상모델을 적용하였다. ANSYS v11.0을 이용한 유한요소 해석은 JIS E 1105 기준과 ASCE 21-98 기준에 따라서 자동무인경전철 차체의 구조 안전성을 평가하였다. 충돌해석은 외연유한요소 해석 프로그램인 LS-DYNA3D를 이용하였다. 충돌 조건은 강체벽에 10km/h의 속도로 정면충돌 사고를 모사하였다. 또한, 수성된 Chang-Chang 파손기준시은 충돌 후 복합재 구조물의 파손 모드를 평가하는데 추천된다.

• Composites Research
• /
• 제21권1호
• /
• pp.22-29
• /
• 2008

본 논문은 유리섬유 에폭시 면재에 알루미늄 하니컴 샌드위치 복합재가 적용된 저상버스 차체에 대한 정면충돌과 전복에 대한 특성에 대해 연구하였다. 이때 충돌과 전복 해석은 외연유한요소 해석 프로그램인 LS-DYNA3D를 이용하였다. 차체 구조물에 적용되는 적층 복합재 면재에 대해 기계적 특성시험을 통하여 물성을 획득하였고, 직교이방성 특성을 갖는 하니컴 심재의 물성은 유효등가손상 모델을 적용하였다. 저상버스의 충돌 해석은 60km/h의 속도로 정면충돌 사고를 모사하여 해석을 수행하였고, 전복해석은 유럽 안전법규 ECE-R66의 시험 방법을 고려하여 해석하였다. 저상버스의 정면충돌과 전복에 대해 운전자와 승객의 생존 공간 안전성에 관한 결과를 보여준다. 또한, 수정된 Chang-Chang 파손기준식은 충돌과 전복해석에 대한 복합재 구조물의 파손 모드 예측에 추천된다.

• 한국군사과학기술학회지
• /
• 제16권3호
• /
• pp.398-404
• /
• 2013

The simulation of the ballistic trajectory of penetrator into the spaced multi-layer RC targets is very important to predict the hitting condition in subsequent target. Because of perturbation by lateral load of penetrator caused by asymmetric hitting position between penetrator and steel bar reinforcement, penetrator rotates and deviates from the straight path. Therefore, penetration capability of penetrator is decreased in the subsequent targets. This paper presents the result of the penetration of steel-bar-reinforced concrete target by using the explicit finite element code LS-DYNA. A series of computations is performed and compared to experimental data and the computed results are in good agreement with the experimental results over a wide range of velocities. And then we conduct the simulation according to various RC target hitting condition and impact velocities.

• 한국기계가공학회지
• /
• 제5권2호
• /
• pp.3-9
• /
• 2006

HSM(High-speed Machining) is widely used in rapid manufacturing of precision products and molds of various materials. Improvement in cutting efficiency is one of the important subjects in the HSM process. To analyse the dynamic behavior during a very short cutting time, the computational analysis code, LS-DYNA3D, was employed for the simulation of the mechanism of HSM for aluminium 7075. This cutting mechanism includes some difficult points in simulation, for example, material and geometrical non-linearity, high-speed dynamic impact, contact with friction, etc. In this paper, a finite element model considering the strain rate effect is proposed to predict the cutting phenomena such as chip deformation, strain and stress distributions, which will help us to design the HSM process.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.756-761
• /
• 2007

This papered is concerned with the crashworthiness characteristics analysis of the non-step bus when it is crashed or roll-over analysis. Computer simulations is implemented using LS-Dyna explicit code which can effectively analysis dynamic response with the lapse of time. We construct a FEM model of the non-step bus under development according to the safety rules used in Europe for composite non-step buses. The crash energy and absorption rate are evaluated to understand crashworthiness characteristic of the composite non-step bus. Body deformation is also examined whether the survival space is secured for passengers.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.226-231
• /
• 2007

This paper studied on the impact fracture modeling techniques of spherical dome with MACOR glass-ceramic. The glass ceramic material has bigger compressive strength than the tensile strength and endure well at high temperature. The fracture simulation under shock perssure was performed by the finite element method with nonlinear code LS-Dyna. The simulation was carried out by 3 type dome models under step impact pulse shape. 4-node shell element and 8-node solid element were used for analysis.

• Computers and Concrete
• /
• 제9권1호
• /
• pp.21-33
• /
• 2012

This paper presents the numerical simulation of the rigid 12.6 mm diameter kinetic energy ogive-nosed projectile impact on plain and fiber reinforced concrete (FRC) targets with compressive strengths from 45 to 235 MPa, using a three-dimensional finite element code LS-DYNA. A combined dynamic constitutive model, describing the compressive and tensile damage of concrete, is implemented. A modified Johnson_Holmquist_Cook (MJHC) constitutive relationship and damage model are incorporated to simulate the concrete behavior under compression. A tensile damage model is added to the MJHC model to analyze the dynamic fracture behavior of concrete in tension, due to blast loading. As a consequence, the impact damage in targets made of plain and fiber reinforced concrete with same matrix material under same impact velocities (650 m/s) are obtained. Moreover, the damage distribution of concrete after penetration is procured to compare with the experimental results. Numerical simulations provide a reasonable prediction on concrete damage in both compression and tension.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.162-167
• /
• 2000

The warm deep drawability in square cup drawing is investigated about a newly developed high-strength steel sheet with retained austenite which is transformed into martensite during forming. For this investigation, six steps of temperature ranges, from room temperature to $250^{\circ}C$, and five kinds of drawing ratio, from 2.2 to 2.6 were adopted. As a result the maximum drawing force and the maximum drawing depth were affected by the elevated temperatures, and the more stable thickness strain distribution was observed to the elevated temperatures. But blue shortness happened over $200^{\circ}C$. The FEM analysis using the LS-DYNA code is adopted to compare the experimental results with the analytical results for thickness strain distribution.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 추계학술대회 논문집
• /
• pp.97-100
• /
• 2000

Today deep drawing and ironing are the major process in manufacturing of battery case used in cellular phone from aluminum. The same technology is utilized in manufacturing of steel or aluminum cans for components of medical instrument, portable PC, walkman and so on. Most of these processes require multi-stage ironing following the deep drawing and redrawing processes. The practical aspects of this technology are well known and gained through extensive experiment and production know-how. However, the fundamental aspects of theses processes are relatively less known. Thus, it is expected that process simulations using FEM techniques would provide additional detailed information that could be utilized to improve the process condition. This paper illustrates the application of process modeling to deep drawing and redrawing operations for High Precision Rectangular Battery Case. A commercially avaliable finite element code LS-DYNA3D was used to simulate deep drawing and redrawing operations.

• 소성∙가공
• /
• 제10권6호
• /
• pp.456-464
• /
• 2001

Deep drawing and ironing are tile major process today in manufacturing of aluminum alloy battery case used in cellular phone. Most of these process require multi-stage ironing following the deep drawing and redrawing processes. The practical aspects of this technology are well known and gained through extensive experiment and production know-how. However, the fundamental aspects of these processes are relatively less known. Thus, it is expected that process analysis using FEM techniques would provide additional detailed information that could be utilized to improve the process condition. This paper illustrates the application of process modeling to deep drawing and redrawing operations. To verify the simulation results, the experimental investigations were also carried out on a real industrial product. The numerical analysis by FEM shows good agreement with the experimental results in view of the deformation shape of the product. A commercially available finite element code LS-DYNA3D was used to simulate deep drawing and redrawing operations.