• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.170-175
• /
• 2008

In this study, it was investigated that the characteristics of startup and compatibility using several type hot and cold gases. The characteristics of starting LRE by pyro starter was compared with that by a Helium spinner. The compatibility of pyro gas, a gaseous Helium, Hydrogen+Nitrogen mixture gas, and air was investigated by a simple 1D turbine analysis considered the properties of each gas and turbine efficiency. Most of them were compatible to start up the LRE however air was properly used only for low power mode of turbine.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.216-220
• /
• 2006

In this study, it was investigated that the characteristics of startup and compatibility using several type hot and cold gases. The characteristics of starting LRE by pyro starter was compared with that by a He spinner. The compatibility of pyre gas, a gaseous He, H2+N2 mixture gas, and air was investigated by a simple 1D turbine analysis considered the properties of each gases and turbine efficiency. Most of them were compatible to start up the LRE but air was properly used only when the turbine was low power mode.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.128-133
• /
• 2005

In this study, performance design programs for components of a turbopump unit (TPU) in a Liquid Rocket Engine (LRE), that has non-cryogenic centrifugal pumps and 1-stage impulse turbine with partial admission nozzle, were developed. The programs were integrated in a TPU module by balancing the mass flow rate for pump-turbine power, and the module was inserted into the LRE system conceptual design program. The fundamental design conditions, satisfying LRE system requirements and minimum mass flow rate condition of gasgenerator, were found and compared with data from a Russian liquid rocket engine.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.185-192
• /
• 2010

Design of velocity-compounded turbine for 75ton class LRE turbopump application and pressure compounded turbine for 30ton class LRE turbopump has been performed. 1D calculation and CFD analysis were conducted in determining blade and flow passage shape of velocity compounded turbine iteratively. Finally, 23.1% improved specific power and 5% reduced weight turbine to the original design was developed. In case of pressure-compounded supersonic turbine design, rotational speed was increased by 50% and the effect of carryover ratio, 2nd nozzle installation angle, leakage flow of 2nd nozzle, and work sharing factor was studied. Final 1D design resulted 36% increased specific power and 51% reduced weight comparing to the original single-row impulse turbine. It is anticipated that nozzle flow path design will be very important for the accomplishment of expected performance of pressure-compounded turbine and nozzle shape optimization will be conducted through the CFD analysis.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.509-512
• /
• 2006

The propellant mixture ratio of gas generator changes when thrust control valve operate to change LRE thrust level. The mixture ratio change of gas generator result in gas temperature change and failure of turbine blade or deterioration of LRE specific impulse. The mixture ratio stabilizer has been developed to maintain propellant mixture ratio of gas generator. This article deals with design and static/dynamic characteristic of stabilizer. Also gas generator system simulation test has shown that the stabilizer can maintain propellant mixture ratio effectively within tolerable range.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2007.11a
• /
• pp.63-67
• /
• 2007

The high pressure turbopump carries out supplying the oxidizer in the liquid propulsion rocket in the combustion chamber. Because an LRE requires a very short starting time , the turbine at the turbopump experiences high torque that was produced by the high pressure and the high temperature. The purpose of this study is to evaluate a turbine blade surface temperature profiles at initial starting 0 ${\sim}$ 0.5 sec. Using $Fine^{Tm}$/turbo, three dimensional Baldwin-Lomax turbulence models are used for numerically analysis. The turbine is composed of 108 blades total, but only 7 rotors were considered because of periodic symmetry effect. Because of interaction with a bow shock on the suction surface, the boundary layer separates from suction surface at inner area of turbine blade. The averaged temperature of the turbine blade tip at 1000 rpm is higher than that of 9000 rpm. Especially at 1000 ${\sim}$ 9000 rpm, temperatures increases on the hub side of the turbine blade tip. Moreover at 9000 rpm, the temperatures from the hub to the shroud of the blade tip increase as well.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.117-122
• /
• 2012

A blisk with rotor shroud is usually adopted in LRE turbine to maximize its performance. However it experiences severe thermal load and resulting damage during engine stating and stop. Shroud splitting is devised to relieve thermal stress on the turbine rotor. Structural analysis confirmed the reduction of plastic strain at the blade hub and tip. However, split gap at the rotor shroud entails additional tip leakage and results performance degradation. In order to assess the effect of shroud split on the turbine performance, tests have been performed for various settings of shroud split. For the maximum number of shroud splitting, measured efficiency reduction ratio was 2.65% to the value of original shape rotor.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2004.03a
• /
• pp.560-564
• /
• 2004

The optimal design and combustion analysis of the gas generator for Liquid Rocket Engine (LRE) were performed. A fuel-rich gas generator in open cycle turbopump system was designed for 10ton$_{f}$ in thrust with RP-1/Lox propellant. The optimal design was done for maximizing specific impulse of main combustion chamber with constraints of combustion temperature and power matching required by turbopump system. Design variables were selected as total mass flow rate to gas generator, O/F ratio in gas generator, turbine injection angle, partial admission ratio, and turbine rotational speed. Results of optimal design show the dimension of length, diameter, and contraction ratio of gas generator. Also, the combustion test was conducted to evaluate the performance of injector and combustion chamber. And the effect of the turbulence ring was investigated on the mixing enhancement in the chamber.r.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.11-15
• /
• 2012

A rotordynamic analysis is performed for a 7 ton class turbopump applied to the third stage LRE(Liquid Rocket Engine) of the KSLV(Korea Space Launch Vehicle). Based on the heritage of the developed experimental 30 ton class turbopump and developing 75 ton class turbopump for the KSLV first and second stage LRE, the 7 ton class turbopump is designed as an one-axis rotor turbopump. Two rotor systems comprised of one oxidizer pump assembly and the other fuel pump-turbine assembly are connected each other using a spline shaft and operating at a design speed. Through the rotordynamic analysis, it is investigated that the turbopump acquires sufficient separate margin of critical speed as a sub-critical rotor.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.4
• /
• pp.25-31
• /
• 2013

A blisk with rotor shroud is usually adopted in LRE turbine to maximize its performance. However it experiences the severe thermal load and resulting damage during engine stating and stop. Shroud splitting is devised to relieve the thermal stress on the turbine rotor. Structural analysis confirmed the reduction of plastic strain at the blade hub and tip. However, split gap at the rotor shroud entails additional tip leakage and results performance degradation. In order to assess the effect of shroud split on the turbine performance, tests have been performed for various settings of shroud split. For the maximum number of shroud splitting, measured efficiency reduction ratio was 2.65% to the value of original shape rotor.