• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.5
• /
• pp.503-508
• /
• 2012

Recently green house gas emission problem has been issued because $CO_2$ emission is known to cause global warming. Hence, introduces more stringent emission and fuel economy requirements in various countries, including Korea. In this research, $CO_2$ emission factor characteristics of in-use cars, which are the most dominant vehicle type in Korea, were studied, and 129 gasoline vehicles, 100 diesel vehicles, and 34 LPG vehicles were tested on a chassis dynamometer. In the tests, CO and $CO_2$ emissions as well as fuel reduction rates weremeasured. The tests were conducted in the CVS-75 mode, which has been considered for developing emission factors for regulating emissions from light-duty vehicles in Korea. Through experiments, correlations among displacement, fuel consumption efficiency, fuel type, mileage, driving pattern, and $CO_2$ emission were investigated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.2
• /
• pp.144-151
• /
• 2016

This study effect of engine oils on regulated fuel economy and emissions including particulate matter (PM) to provide basic data for management of engine oil in vehicles. Three engine oils (Group III base oil, Group III genuine oil with additive package and synthetic oil with poly alpha olefins (PAOs)) were used in one gasoline, one LPG(liquefied petroleum gas) and two diesel vehicles. In the case of diesel vehicles, one is a diesel vehicle without DPF (diesel particulate filter) other is a diesel vehicle with DPF. In this study, the US EPA emission test cycle FTP-75, representing city driving, was used. HORIBA, PIERBURG, and AVL gas analyzers were used to measure the fuel economy and regulated emissions such as CO, NOx, and THC. The number of PM was measured using a PPS (pegasor particle sensor). And, the shape of PMs was analyzed by SEM (scanning electron microscope). The effects of oil type on fuel economy, exhaust gas, and PM were not significant because engine oil consumption by evaporation and combustion in the cylinder is very tiny. Fuel and vehicle type were dominant factors in fuel economy and emissions. HC emission from gasoline vehicles was higher than that from other vehicles and NOx emission from diesel vehicles was higher than that from other vehicles. The number of PM was not affected by the engine oil, but by the driving pattern and fuel. The shapes of the PM, sampled from each vehicle using any test engine oil, were similar.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.1
• /
• pp.148-156
• /
• 2000

For the in-line three cylinder engine whose crankshaft has a phase of 120 degrees, the total sum of unbalanced inertia forces occurring in each cylinder will be counterbalanced among three cylinders. However, parts of inertia forces generated at the No.1 and No.3 cylinders will cause a primary moment about the No.2 cylinder. In order to eliminate this out-of-balance moment, a single balance shaft has been attached to the cylinder block so that the engine durability and riding comfort may be further improved. Accordingly, the forced vibration analysis of the in-line three cylinder engine must be implemented to meet the required targets at an early design stage. In this paper, a method to reduce noise and vibration in the 800cc, in-line three cylinder LPG engine is suggested using the multibody dynamic simulation. The static and dynamic balances of the in-line three cylinder engine are investigated analytically. The multibody dynamic model of the in-line three cylinder engine is developed where the inertia properties of connecting rod, crankshaft, and balance shaft are extracted from their FE-models. The combustion pressure within the No.1 cylinder in three significant operating conditions(1500rpm-full load, 4000rpm-full load and 7000rpm-no load)is measured from the actual tests to excite the engine. The vibration velocities at three engine mounts with and without balance shaft are evaluated through the forced vibration analysis. Obviously, it is shown that the vibration of the in-line three cylinder engine with balance shaft is reduced to the acceptable level .

• Applied Chemistry for Engineering
• /
• v.17 no.1
• /
• pp.82-86
• /
• 2006

When a domestically manufactured floater is used in a general gasoline or LPG car, or a flowmeter is floated long time in the engine oil under above $150^{\circ}C$, the floater will be swelled or its organization will be slackened because weight and volume will be changed due to the osmosis of fuel. In this study, we conducted a research on a manufacturing technique of a foam-floater with the small changse in weight and volume, oil-resistance, and thermal resistance in the high temperature engine oil. When the prepared floater TROF II-3, where Nitrile Butadiene Rubber (NBR) as basic material of the floater was superseded by Hydrogenated Nitrile Butadiene Rubber (HNBR), was floated for 100 h at the engine oil of high temperature ($150^{\circ}C$), the change rates of the weight and the volume were 2.90%, and 2.56%, respectively. These were less than the NBR (TROF I-3) case, where the change rates of the weight and the volume were 10.81% and 3.08%, respectively, Therefore, TROF II-3 was determined to be suitable as an engine-oil floater in high temperature because the change of weight and volume were small, the appearance, and the specific gravity of floater were maintained uniformly in the high temperature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.8
• /
• pp.2626-2636
• /
• 1996

A study of soot deposition and reentrainment was carried out both theoretically and experimentally to understand behavior of soot formed by incomplete combustion in a diesel engine. Theoretically, soot deposition on engine cylinder wall and/or piston head was studied with a stagnation point flow approximation. Soot reentrainment occurred upon exhaust gas blowdown was also studied by assuming a long-normal shear velocity distribution. Experimentally, a LPG$O_2/N_2$ flame impinging on a disk, produced by a concentric tubular burner, was chosen as deposition configuration and a shear flow unit with compressed air was installed for the study of reentrainment. For selected flame configuration, soot deposition measurements were conducted and showed that the dominant deposition mechanism was thermophoresis. Distributions of gas temperature and soot number density were estimated by combining data obtained by a B-type thermocouple with a thermophoretic transport theory. Disk temperature distributions were directly measured using a K-type thermocouple. Soot size and morphology were estimated from a TEM photograph. Ratios of soot deposit to reentrained amount were measured for a wide range of shear flow velocities, which showed that the reentrainment model was reasonable.

• Transactions of the Korean hydrogen and new energy society
• /
• v.10 no.4
• /
• pp.233-243
• /
• 1999

Combustion characteristics of synthetic gas from flame pyrolysis gasification of polymetric wastes are reported and the applicability of synthetic gas from flame pyrolysis gasification to a gas engine system is presented. Engine power is easily predicted by the volume percentage of the synthetic gas. Measurements have been made to obtain the range of flame existence in the function of volume percentage of CO and $H_2$ gases in the synthetic gas. In order to clarify the emission of the flames, NOx measurements by chemiluminescent analyser are taken in flames with different equivalent ratios. From the results of the engine performance data we also have demonstrated that the output of the gas engine modified from a LPG engine is about 5 ps at normal rating. We conclude that synthetic gas from flame pyrolysis gasification of polymetric wastes is applicable to a gas engine system.

• Journal of ILASS-Korea
• /
• v.14 no.1
• /
• pp.34-38
• /
• 2009

This paper presents the pulsation of carburetor inlet and outlet pressure of a small SI gasoline engine. The engine used in this paper is a 23cc, single cylinder, diaphragm carburetor, two-stroke, air-cooled for brush cutter. The rpm and pressure wave pulsation at the inlet and the outlet of carburetor were measured and analysed for the understand of the internal air flow into the barrel on the diaphragm carburetor. These data should be used for the development of the duel fuel injection system for gasoline and LPG. The results showed that the carburetor inlet pressure variations were very steady, but the pressure variations at carburetor outlet were very sensitive to the pressure variation into the crank case and were to similar independently to the engine speed on partial opened throttle conditions. According to increasing engine speed, the pressure waves started to come out and be developed after closing the intake port of the engine at carburetor outlet. Reverse flow occurred on the WOT (wide open throttle) condition.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2005.10a
• /
• pp.592-597
• /
• 2005

Biogas is widely accepted as one of renewable energy. Raw biogas can be used in internal combustion engines either spark ignition or diesel engines. Since the gas has relatively low calorific values, engine power also is lower than rated power values. Modified engines or biogas-specific engines have been utilized in order to increase efficiency. Recently, gas engine/generators are provided for various purposes. They are mostly for LPG or natural gas. When biogas is fueled to the gas engines, de-rating is inevitable due to its lower calorific values. Meanwhile, massively produced commercial gas engines are more competitive in terms of initial investment for engines, compared to biogas-specific engines. Then, the characteristics of the commercial engine and power generation should be understood for better operation. A 5kW gas engine/generator(natural gas) was tested for determining an allowable maximum concentration of $CO_2$ in synthetic biogas, with respect to engine stating, power generation. Experimental results indicated that about 65% of methane concentration is required to start the gas engine. At this condition, the power generated was about 3 kW. It is about 60% of the nominal power, which is similar to the ratio of calorific values.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.1108-1119
• /
• 2018

As the interest on the air pollution is gradually rising at home and abroad, automotive and fuel researchers have been studied on the exhaust and greenhouse gas emission reduction from vehicles through a lot of approaches, which consist of new engine design, innovative after-treatment systems, using clean (eco-friendly alternative) fuels and fuel quality improvement. This research has brought forward two main issues : exhaust emissions (regulated and non-regulated emissions, PM particle matter) and greenhouse gases of vehicle. Exhaust emissions and greenhouse gases of automotive had many problem such as the cause of ambient pollution, health effects. In order to reduce these emissions, many countries are regulating new exhaust gas test modes. Worldwide harmonized light-duty vehicle test procedure (WLTP) for emission certification has been developed in WP.29 forum in UNECE since 2007. This test procedure was applied to domestic light duty diesel vehicles at the same time as Europe. The air pollutant emissions from light-duty vehicles are regulated by the weight per distance, which the driving cycles can affect the results. Exhaust emissions of vehicle varies substantially based on climate conditions, and driving habits. Extreme outside temperatures tend to increasing the emissions, because more fuel must be used to heat or cool the cabin. Also, high driving speeds increases the emissions because of the energy required to overcome increased drag. Compared with gradual vehicle acceleration, rapid vehicle acceleration increases the emissions. Additional devices (air-conditioner and heater) and road inclines also increases the emissions. In this study, three light-duty vehicles were tested with WLTP, NEDC, and FTP-75, which are used to regulate the emissions of light-duty vehicles, and how much emissions can be affected by different driving cycles. The emissions gas have not shown statistically meaningful difference. The maximum emission gas have been found in low speed phase of WLTP which is mainly caused by cooled engine conditions. The amount of emission gas in cooled engine condition is much different as test vehicles. It means different technical solution requires in this aspect to cope with WLTP driving cycle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.101-107
• /
• 2007

This study investigated the wear of the valve and seat insert seating faces. A tester, an exhaust valve and a seat insert were used. Test variables were cycle numbers ($2{\times}10^6,\;4{\times}10^6,\;6{\times}10^6\;and\;8{\times}10^6$) and Hz (10Hz and 25Hz). The other test conditions such as temperature ($350^{\circ}C$), fuel (LPG) and load (1960N) were fixed. The 10Hz tests indicated that the average Rmax of the valve increased at the rate of $7.76{\mu}m/10^6$ cycles starting from $29.42{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $8.57{\mu}m/10^6$ cycles starting from $34.19{\mu}m$ at the $2{\times}10^6$ cycles. The 25Hz tests indicated that the average Rmax of the valve increased at the rate of $1.58{\mu}m/10^6$ cycles starting from $74.2{\mu}m$ at the $2{\times}10^6$ cycles and that of the seat insert increased at the rate of $1.25{\mu}m/10^6$ cycles starting from $83.95{\mu}m$ at the $2{\times}10^6$ cycles. The tribochemical reaction product covered the two seating faces, preventing the wear of the seating faces. As cycle numbers became greater, the average Rmax of the seating faces became greater, but the increase rate varied significantly depending on the Hz. The wear mechanism of the two faces was investigated through the tribochemical reaction.