• Tribology and Lubricants
• /
• 제14권1호
• /
• pp.7-13
• /
• 1998

The static characteristics of a five-pad tilting pad journal bearing of load on pad (LOP) type have been investigated experimentally under the different values of bearing load and shaft speed. The diameter and length of the bearing are 300.91 mrn and 149.8 mm, reslx;ctively. Circumferential distribution of the film pressure, film thickness, journal surface temperature and beating surface temperature are measured. A noticeable inlet pressure rise is observed at the entrance of each pad, especially the bottom pad. The inlet pressure is increased by the increase of shaft speed as well as bearing load. In the five-pad tilting pad joumal bearing of LOP type, almost all of beating load is being carried only by the bottom pad. The maximum bearing surface temperature is observed at near the minimum film thickness. It is observed that the metal temperature of the mid-plane is higher than that of the edge at the inlet region, while the metal temperature of the edge is higher than that of the mid-plane at the outlet region.

• 품질경영학회지
• /
• 제47권3호
• /
• pp.425-435
• /
• 2019

Purpose: The purpose of this study was to resolve the Naval ship's Local Operation Panel(LOP) malfunction problems which caused by overheating in summer season and dispatching to equatorial regions. Methods: Instead of using dual type heat insulation materials(consist with ceramic wool and glass wool), aerogel heat insulation materials were used for decreasing heat emissions from gas-turbine heat waste steam pipes passing water-jet- room. Experiment and Computational analysis of heat flow were conducted to analyze the internal room temperature changes. Results: The results of this study are as follows; The aerogel heat insulation materials suppress heat emission more efficiently than dual type insulation materials. The cold surface temperature of insulation was far more decreased and internal room, LOP surface temperature also showed significant results too. Conclusion: The substituted heat insulation materials appeared remarkable performance in decreasing room temperature that it could be used for suppressing the LOP overheatings and malfunctions.

• 한국소음진동공학회논문집
• /
• 제21권8호
• /
• pp.752-760
• /
• 2011

In tilting pad bearing design process, the selection of the proper configuration type of either a load-between-pad(LBP) or load-on-pad(LOP) as well as preload and pivot offset conditions is to be carefully considered. Also the bearing needs to be designed in order to be suited for the rotor-bearing system and operating condition. In this paper, it is observed that the dynamic characteristics in a five pad tilting pad bearing for the LBP and the LOP configurations are influenced by the variation of preload and pivot offset. In this context, rotor dynamic analysis of the 5 MW industrial gas turbine supported by the tilting pad bearing at the front and roller bearing at the rear is carried out based on the dynamic coefficients of the tilting pad bearing investigated. The result shows that two rigid body critical modes experience various changes according to the influence of the tilting pad bearing uniquely applied to one side of this machine. Mainly, the second critical speed, the rigid body mode of conical shape with high whirling in the tilting pad bearing, is significantly changed by preload and pivot offset regardless of the LBP and LOP configurations. And, the first critical mode, the rigid body mode of conical shape with high whirling in the roller bearing, is sensitively affected by preload applied to the LOP configuration and by its asymmetric dynamic properties.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 춘계학술대회 논문집
• /
• pp.425-432
• /
• 2011

In tilting pad bearing design process, the selection of the proper configuration type of either a Load-Between-Pad (LBP) or Load-On-Pad (LOP) as well as preload and pivot offset conditions is to be carefully considered. Also the bearing needs to be designed in order to be suited for the rotor-bearing system and operating condition. In this paper, it is observed that the dynamic characteristics in a 5 pad tilting pad bearing for the LBP and the LOP configurations are influenced by the variation of preload and pivot offset. In this context, rotor dynamic analysis of the 5MW industrial gas turbine supported by the tilting pad bearing at the front and roller bearing at the rear is carried out based on the dynamic coefficients of the tilting pad bearing investigated. The result shows that two rigid body critical modes experience various changes according to the influence of the tilting pad bearing uniquely applied to one side of this machine. Mainly, the second critical speed, the rigid body mode of conical shape with high whirling in the tilting pad bearing, is significantly changed by preload and pivot offset regardless of the LBP and LOP configurations. And, the first critical mode, the rigid body mode of conical shape with high whirling in the roller bearing, is sensitively affected by preload applied to the LOP configuration and by the its asymmetric dynamic properties.

• 한국환경과학회지
• /
• 제12권2호
• /
• pp.151-155
• /
• 2003

The resources conservation system is comprehended, making Taean-haean National Park a research material by applying the fact of landowning, designating an LOP and Korea and Japan's Natural Park Act. Following conclusions were obtained in this study; Most of land areas of the National Park are privately owned; Only a few have been designated as Natural Reservation, a core reserved area on LOP, and a sandy beach, a sand dune, a sand spit, a tidal flat, a wetland, etc are distributed in the natural environment area so they were exposed to development; As seen in most of coastal type of National Parks, 13 commercial beaches are established. The annual rush to the beaches appears in July and August; Sand dune areas that have to be managed in terms of conservation, are turned into beaches. Moreover, the collective facilities areas are randomly developed. So they fail to function originally; The current Natural Park Act has no systematic devices for conservation of the natural resources on the seashore or offshore.

• 한국소음진동공학회논문집
• /
• 제13권6호
• /
• pp.467-473
• /
• 2003

This paper describes the fluttering characteristics of the upper pad in a tilting pad journal bearing(6-pad, LOP type) using a steam turbine. In order to investigate the phenomena of the upper pad fluttering experimentally, the absolute vibration of the upper pads, the relative vibration between bearing and shaft and the circumferential distribution of the film thickness are measured under the different values of supply oil flow rate, shaft speed and bearing load. It can be known that the fluttering mechanism of the upper pads has a tendency of the self-excited vibration from the study of fluttering frequencies and amplitudes with the change of shaft speed. Furthermore, it is observed that the incipient upper pad fluttering velocity is increased by the increase of oil supply flow rate and the fluttering amplitude of the upper pads is increased by the decrease of the ell flow rate and by the increase of the bearing load.

• 한국가스학회지
• /
• 제17권1호
• /
• pp.19-25
• /
• 2013

용접에 의한 가스설비, 교량, 선박 등 강 구조물의 접합 방법은 대부분 십자형이나 T형의 필릿 용접으로 이루어지며 구조물의 형상과 용도에 따라 완전 용입 또는 불완전 용입 상태로 이루어진다. 본 연구에서는 십자형 필릿용접 구조물에 대하여 재료 두께별 용입 깊이에 따른 피로 균열 특성을 파악하였고, 그 결과로부터 무한수명 영역내에서의 안전 설계응력에 대하여 고찰하였다. 미 용입 길이가 길면 루트 부 파괴가 되어 무한 수명 영역은 작고 미 용입 길이가 짧으면 토우부 파괴가 되어 무한 수명 영역은 크게 나타났다. 3층 용접한 재료 두께 20mm의 경우가 2층 용접한 재료 두께 10mm, 15mm의 경우보다 미세한 페라이트 침상 조직을 더 많게 형성시켜 노치 인성을 증가시키므로 서 피로강도와 무한 수명을 더 향상시킨 것으로 나타났다.

• 한국유체기계학회 논문집
• /
• 제2권2호
• /
• pp.32-38
• /
• 1999

An experimental study is performed to investigate the frequency effects of the excitation force on the linear stiffness and damping coefficients of a LOP (load on pad) type five-pad tilting pad journal bearing with the diameter of 300.91 mm and the length of 149.80 mm. The main parameter of interest in the present work is excitation frequency to shake the test bearing. The excitation frequency is controlled independently, using orthogonally mounted hydraulic exciters. The relative movement between the bearing and shaft, and the acceleration of the bearing casing are measured as a function of excitation frequency using the different values of bearing load and shaft speed. Measurements show that the variation of excitation frequency has quite a little effect on both stiffness and damping coefficients. Both direct stiffness and damping coefficients in the direction of bearing load decrease by the increase of shaft speed, but increase with the bearing load.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1998년도 유체기계 연구개발 발표회 논문집
• /
• pp.173-179
• /
• 1998

An experimental study is performed to investigate the frequency effects of the excitation force on the linear stiffness and damping coefficients of a LOP (load on pad) type five-pad tilting pad journal bearing with the diameter of 300.91 mm and the length of 149.80 mm. The main parameter of interest in the present work is excitation frequency to shake the test bearing. The excitation frequency is controlled independently, using orthogonally mounted hydraulic exciters. The relative movement between the bearing and shaft, and the acceleration of the bearing casing are measured as a function of excitation frequency using the different values of bearing load and shaft speed. Measurements show that the variation of excitation frequency has quite a little effect on both stiffness and damping coefficients. Both direct stiffness and damping coefficients in the direction of bearing load decrease by the increase of shaft speed, but increase with the bearing load.

• Tribology and Lubricants
• /
• 제14권1호
• /
• pp.14-22
• /
• 1998

This paper describes the effects of exciting frequency on the stiffness and damping coefticients of a 5-pad tilting pad journal bearing, LOP (load on pad) type. The stiffness and damping coefficients are investigated experimentally under the different values of exciting frequency, bearing load and shaft speed. These coefficients are estimated by measuring the response of the relative displacement between the bearing and the shaft and acceleration of the bearing due to the known exciting loads acting on the bearing. In order to analysis the response of exciting load, displacement and acceleration, a FFT analyzer is used. It is shown that the variation of exciting frequency has a little effect on both the stiffness and damping coefficients. Both the stiffness and damping coefficients in the loading direction are decreased by the increase of shaft speed but increased by the increase of bearing load.