• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.4
• /
• pp.632-637
• /
• 2016

A streetlight control system was developed using information technology and LED lights for efficient management and energy savings. The proposed system can control the power usage of an LED streetlight luminaire using GPS satellite communication and an Arduino with a built-in microprocessor. A control circuit was designed to control the current using GPS, a control unit, transistor, resistor, and constant-current supply circuit. The circuit was validated through experiments with normal operation. Using GPS, the control system extracts accurate time and location information according to the season, and it controls the current supplied to the LED streetlight according to the extracted time. Power consumption was reduced by more than 11%. The control system could reduce accidents caused by conventional lighting systems used to save energy, and it could improve the inefficient management of energy by preserving constant brightness of a streetlight at times and in areas that have less traffic.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.4
• /
• pp.127-134
• /
• 2015

VLC(Visible Light Communication) is the technology to send and receive data by using visible light that LED emits. The basic principle of VLC is the communication by using flashing(ON/OFF) of the light from the LED that changes electricity to light in short time. As the recent advances in LED technology, VLC is also received a lot of attention and the research about it is in progress actively. Especially, the interest about indoor VLC system is increasing because the visible light can't pass through the wall. In this paper, we compose the indoor SISO VLC system with NRZ-OOK and VPPM modulation schemes. Also, we apply SR-ARQ, a kind of re-transmission error control schemes, to the VLC system. And then, we compare and analyze the performance of communication according to the location of receiver and the type of modulation by using BER, the number of transmission and throughput.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.37C no.9
• /
• pp.784-790
• /
• 2012

In this paper, we propose a upstream transmission method to extend coverage in visible light communication (VLC) systems. We extend transmission distance by using focused infrared(IR) light emitting diodes(LEDs). Since the focused light covers just limited area, it might have a difficulty in transmitting data if the transmitter and receiver are not properly aligned. To solve this problem, we arrange multiple IR-LEDs in different direction and select a single best performing IR-LED among multiple IR-LEDs. Also, the transmission performance is periodically checked and another IR-LED is reselected to support the required quality of service (QoS) and to minimize battery consumption required by a mobile terminal.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.66-72
• /
• 2016

An LED lighting control system was developed to combine information technology and LED lights for efficient management and energy savings. The system can monitor and control the status of an LED luminaire using Bluetooth wireless communication, sensor technology, and smart phones. An LED lighting control circuit was designed using a temperature sensor, illumination sensor, and Bluetooth module with a fuzzy constant-current control circuit. We extended the lifetime and prevented damage to the LED by optimizing the supply current of the LED luminaire based on the heat-generation temperature of $70^{\circ}C$ of an LED heat sink. We also automatically adjusted the ON/OFF time depending on the ambient illumination of the LED luminaire. By allowing easy control of the LED luminaires on a smartphone, we improved the efficiency and achieved energy savings. The control system was validated through experiments for normal operation.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.4
• /
• pp.127-135
• /
• 2010

A study on that LED in 36[W] class replaces broadcast illuminator to save energy and improve the quality of film because tungsten halogen illuminators are too hot and spending lots of electrical capacity at the time of camera shooting. And the following result was obtained .36[w] LED lighting fixture's illuminance is lower than 1[kw] halogen Light but object's illuminance became higher, and at the image be showed very bright and softly.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.12 no.1
• /
• pp.66-74
• /
• 2013

This paper introduces the improvement of QoS to compensate the decreasing LED performance by temperature characteristic in the LED-ID communication system. LED does not only use as a lighting device, but also uses as a communication device. The conventional system is transmitted by RGB of LED following the mixture color ratio, which determined the color of lighting, and the BER performance of each RGB signals. However, when the LED used consistently, it has occurred the heat temperature. As a result, LED is degraded the performance by increased temperature each device. To solve this problem, we proposed the adaptive modulation and coding scheme by temperature of device to improve the performance of system and satisfied the QoS in the LED-ID system.

• Korean Journal of Optics and Photonics
• /
• v.30 no.5
• /
• pp.193-196
• /
• 2019

The design and control of thermal flow is important for the operation of high-power laser diodes (LDs). It is necessary to analyze and improve the thermal bottleneck near the active layer of an LD. As the error in prediction of the thermal resistance of an LD is large, typically due to the hyperbolic increase and saturation to linear increase of the thermal resistance as a function of thickness, it is helpful to use a simple, modified divergence model for the improvement and optimization of thermal resistance. The characteristics of LDs are described quite well, in that the values for simulated thermal resistance curves and the thermal cross section followed are almost the same as the values from the model function. Also, the thermal-cross-section curve obtained by differentiating the thermal resistance is good for identifying thermal bottlenecks intuitively, and is also fitted quite well by the model proposed for both a typical LD structure and an improved LD with thin capping and high thermal conductivity.

• Journal of Navigation and Port Research
• /
• v.39 no.4
• /
• pp.299-305
• /
• 2015

Modbus is a serial communications protocol, it has since become a practically standard communication protocol, and it is now a commonly available means of connecting industrial electronic devices. Therefore, it can be connected with all devices using Modbus protocol to the measurement and remote control on the ships, buildings, trains, airplanes and etc.. In this paper, we add the Modbus communication protocol to the existing lighting controller sensitivity to enable verification and remote control by external environmental factors, and also introduces a fuzzy inference system was configured by external environmental factors to control LED lighting. External environmental factors of temperature, humidity, illuminance value represented by the LED through a fuzzy control algorithm, the values accepted by the controller through the sensor. Modbus is using the RS485 Serial communication with other devices connected to the temperature, humidity, illumination and LED output status check is possible. In addition, the remote user is changed to enable it is possible to change the RGB values in the desired color change. Produced was confirmed that the LED controller output is based on the temperature, humidity and illumination.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.10 no.5
• /
• pp.579-586
• /
• 2015

In this paper, we design and implement a lighting system which has a capability of adjusting brightness and colors of LED module. The lighting systems is consisted of RGB and white LEDs controlled by a micro-processor. All colors in nature can be synthesized in our lighting system by controlling brightness of 4 color LEDs individually. The current flowing to LED is limited to a maximum set value to extend the LED life time using PWM current control. The control module also includes the function that it can save and load brightness and color data set by the user. The implemented lighting system passed the electromagnetic compatibility(EMC) test such that it can be used as a commercial product.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.4
• /
• pp.954-964
• /
• 2015

In this research, an overlapped illumination model was newly proposed for designing a freeform LED lens with a uniform illuminance distribution on its illuminating plane. Based on the proposed model and conventional illumination models, freeform lenses were designed and their performances and tolerances were compared. As a result of the tolerance analysis about thickness change in lens, position, size change, central direction change of light emission and characteristic change in LED source. This proposed model and divergent illumination model are similar to the performance about central direction change of light emission in LED source. but the uniformity illumination value in this proposed model is more remarkably value than it in divergent illumination model about characteristic change in LED source.