• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제32회 KOSCO SYMPOSIUM 논문집
• /
• pp.157-163
• /
• 2006

A new technique utilizing LII signal for the measurement of flow velocities of laminar diffusion flames has been investigated. Soot particles in ethylene diffusion flames are heated by a modulated Ar-ion laser beam. LII signals and their phase angles are measured using a lock-in amplifier at the different flame heights and the axial flow velocity are obtained from the measured phase angle delay. The measured velocities are similar to those from LDV measurements under the same operating conditions. The effects of laser power, LII signal wavelength, and modulation frequency are not sensitive to the velocity measurement. However, the choice of an optical chopper blade type could affect the measurement result. The use of a 6/5 chopper blade showed the better result that is possibly due to the square shape of modulated laser beam. This study successfully demonstrated that axial flow velocities of laminar diffusion flames can be measured by a new technique utilizing LII signal, which does not need particle seeding unlikely to LDV or PIV techniques.

• 설비공학논문집
• /
• 제15권3호
• /
• pp.177-186
• /
• 2003

In the present study, the flow characteristics of developing turbulent flows are investigated at the exit region of a square cross-sectional 180" curved duct with dimensions of 40mm$\times$40mm$\times$4000mm (height $\times$ width $\times$length). Smoke particles produced from mosquito coils were used as seed particles for the LDV measurement. Experiments were carried out to measure axial velocity profiles, shear stress distributions and entrance lengths by using an LDV system and Rotating Machinery Resolver RMR with PHASE software. Experimental results clearly show that the time-averaged Reynolds number does not affect oscillatory flow characteristics because the turbulent components tend to balance the oscillatory components in the fully developed flow region. Also, the velocity profiles are in good agreement with 1/7power law such as the results of steady turbulent flows. The turbulent intensity linearly increases along the walls and is slightly higher, especially in the period of deceleration. On the other hand, the LDV measurements show that shear stress values in slightly higher in the period of deceleration due to the flow characteristics in the exit region. The entrance length where flows become stable appears at the point that is 40 times the length of hydraulic diameter.eter.

• 한국산학기술학회논문지
• /
• 제15권9호
• /
• pp.5854-5860
• /
• 2014

본 연구에서는 대표적인 토목구조물인 교량에서 영상 기반 변위 계측장치(VDMS)를 이용하여 변위를 측정하고, 고가의 변위측정장비인 LDV와의 비교를 통하여 그 현장 적용 성능을 평가하였다. 본 연구에서 사용한 VDMS는 카메라와 마커, 프레임 그래버, 노트북으로 구성되었으며, 마커를 구조물에 부착하여 그 영상을 촬영하고 평면 호모그래피 기법을 이용하여 마커가 부착된 구조물의 변위를 측정하는 장치이다. 개발된 VDMS의 성능 검증을 위하여 우선 소형 구조물을 이용한 간단한 실내 실험을 수행하였다. 다음으로 실제 철도교량에서 KTX를 다양한 조건으로 주행하고, 그에 의하여 발생한 변위를 VDMS과 LDV를 이용하여 계측한 뒤, 얻어진 두 변위를 비교하여 VDMS의 현장 적용 성능을 평가하였다.

• 한국음향학회지
• /
• 제41권5호
• /
• pp.589-600
• /
• 2022

탄도형 체외 충격파 치료기의 출력 에너지를 측정하는 Dry Test Bench(DTB)의 신뢰성을 검증하기 위해, 상용 탄도형 충격파 치료기에 대해 Laser Doppler Vibrometer(LDV)로 측정된 충격파의 음향 에너지와 비교했다. 실험 결과, DTB로 측정된 역학적 에너지는, 동일한 출력 설정에서, 5 % 이내의 변동성을 보이며, 치료기의 전 출력 설정 범위에서 LDV로 측정된 충격파의 음향 에너지와 선형적인 상관성(adj. R² = 0.991)을 확인했다. 두 측정 방법의 상관성과, LDV을 이용하여 공기 및 수중에서 측정된 충격파 음향 에너지의 상관성(adj. R² = 0.995)을 통합하면, DTB 측정으로부터 수중에서 발생된 충격파의 energy flux density를 평균 7.85 % 오차로 추정된다. DTB는 치료기의 출력에너지에 대한 정보만 제공하기 때문에, IEC61846 및 IEC63045에서 요구하는 다양한 충격파의 음향 출력을 시험하는 도구로 적합하지 않다. 그러나 측정 원리가 단순하고 사용이 용이한 DTB는 제조사 및 사용자가 탄도형 Extracorporeal Shock Wave Therapy(ESWT) 치료기의 성능을 관리하는 목적으로 유용하게 사용될 수 있을 것으로 기대된다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.720-726
• /
• 2001

Two-dimensional, angle-resolved LDV(Laser Doppler Velocimetry) measurements of the turbulent rotating flow field in a confined cylinder have been performed. The configurations of interest are flows between a rotating upper disk with a rod attached by a disk or impeller(${\theta}= 90^{\circ},\;45^{\circ}$) and a stationary lower disk in a confined cylinder. The mean flow velocity as well as the turbulent intensity of the flow field have been measured. The results show that the flow is strongly dependent on the position of the impellers or the disk, negligibly affected by the Reynolds number in turbulent flow. It is observed that the mixing effect of the axial flow impeller(${\theta}= 45^{\circ}$) is better than that of the radial flow impeller(${\theta}= 90^{\circ}$) or a disk.

• 기계저널
• /
• 제33권12호
• /
• pp.1063-1068
• /
• 1993

왕복식엔진에서 연소과정은 실린더내 유체유동에 지배되므로 최적조건의 엔진설계를 위해서는 실린더내 유체유동을 효과적으로 이용하는 것이 필요하다. 연소과정에 중요한 영향을 미치는 압축말기 연소실내 난류강도는 흡입과정시 생성된 유동의 에너지가 압축과정을 거치면서 작은 스케일의 에디(eddy)로 깨지면서 발생된다. 연소과정시 이러한 에디들은 초기화염생성을 촉진 시키고 화염전파속도를 증진시키는 역할을 함으로써 실린더내 유체유동에 대한 이해증진을위해 실린더내 평균속도 및 난류유동을 측정하는 연구들이 많이 진행되고 있다. 엔진유동은 매사이 클의 유동이 엄밀히 주기적인 운동을 하지 않고, 각 사이클의 유동이 비정상유동을 하며, 유동의 생성 및 소멸이 매우 짧은 특성을 가진다. 따라서 산란입자가 측정체적을 통과할 때 속도데이 터가 발생하는 LDV(laser Doppler velocimetry) 측정에 있어서 레이저빔의 산란광노이즈 감소와 산란입자의 효율적인 공급으로 데이터 발생률을 높이는 것이 어려운 점이다. 이 글에서는 엔진 유동의 LDV측정시 고려해야 할 문제점들, 실험장치구성, 그리고 데이터처리 방법과 주요측정 결과에 대해 본 연구팀에서 지금까지 수행한 연구결과를 토대로 하여 기술하고자 한다.

• 한국자동차공학회논문집
• /
• 제2권5호
• /
• pp.66-73
• /
• 1994

The configuration effects of a tumble adaptor which transforms tumble into swirl on the intake tumble characterization under steady flow condition have been investigated by LDV measurement The following parameters were involved to test their effects on tumble-swirl conversion characteristics ; the cylinder height and its bottom shape, measuring position in the swirl induction pipe, and the relative direction of the induction pipe. The short cylinder height and the flat bottom of the tumble adaptor were found effective for the generation of tumble in the cylinder, allowing higher tumble-swirl conversion efficiency.

• 한국분무공학회지
• /
• 제21권4호
• /
• pp.207-213
• /
• 2016

To protect air pollution of urban area from motor vehicles, emission limits for diesel vehicles have been dramatically lowered in short period. But recent studies have shown that on-road NOx emissions of light-duty diesel vehicles are considerably higher than the values measured with laboratory test procedures used for emission certification. To tackle with this issue, Ministry of Environment have a plan to introduce EU RDE-LDV (Real-driving Emission-Light-duty Vehicle) regulation. In this study, 4 Euro 6 diesel vehicles have been tested with the new test procedures published by EU to estimate on-road NOx emissions using PEMS (Portable Emission Measurement System). The results have shown that the requirements of EU RDE-LDV could be met in driving condition of metropolitan area for constitution of test routes and validity of test results. In analysing with Moving Averaging Window method the completeness and normality of test data were validated with the requirement. On-road NOx emissions were quite deviated as test vehicles and higher than the new limit of on-road NOx emission enforced from Sept. 2017, which means that RDE-LDV can effectively reduce NOx emission of diesel vehicles in real driving conditions of Korea.

• 한국자동차공학회논문집
• /
• 제9권5호
• /
• pp.46-53
• /
• 2001

To optimize the intake flow condition in the heavy-duty LPG SI engine, five different swirl ratios of intake port were investigated experimentally by oil spot method, LDV and single cylinder engine test. The flow characteristics near the piston surface were observed by oil spot method and magnitudes of swirl flow were measured quantatively by LDV method in the steady flow rig. The engine performances of various swirl flow were also tested with the heavy-duty LPG SI single cylinder engine. In the results, high swirl ratio, above $R_s$=2.3, was not suitable to develope a stable flame kernel and to produce high engine performance. Especially it was more serious under lean burn conditions, since turbulence intensity was smaller than bulk flow though those are increased together. These results were also confirmed by LDV measurement and oil spot method. On the contrary, low swirl ratio($R_s$=1.3) is not good to propagate a flame since the turbulence intensity and bulk flow are vanished during compression stroke and low swirl ratio has too weak initial energy for stable combustion. Therefore, the of optimized swirl ratio f3r the heavy-duty LPG engine in this work was found around $R_s$=2.0.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.287-296
• /
• 2017

Although emission regulations have been gradually strengthened in the past decade, the road transport section remains the most important source of NOx emission in air pollution. One reason is that there has been an increase in the proportion of diesel vehicles and in the volume of traffic. In addition, the certification procedure for standard emission limit does not sufficiently reflect real traffic condition and various driving patterns. Therefore, the European Commission(EC) has recently come up with the RDE-LDV(Real driving emissions-light duty vehicle) regulations, and the Ministry of Environment in Korea has been conducting research on evaluating RDE-LDV with PEMS(Portable Emission Measurement Systems). According to the trip requirements of the 2nd RDE package announced by the EC, the objectives of the present study include the development of Korean RDE routes to reflect domestic traffic and road conditions. Based on the results, both RDE routes are in correct compliance with RDE-LDV regulations, including trip requirements and trip dynamics. KOR-NIER Route 1, in particular, has a higher driving load in rural driving with regard to excessive gradient of elevation compared to KOR-NIER Route 2, including relatively plane rural driving.