• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.200-202
• /
• 2007

Improvement of LC mixtures can be realized by the development of new molecules in combination with the identification of advanced mixture concepts. By new high-polar single materials rotational viscosity has recently been improved significantly. Now, a new LC mixture concept for IPS and FFS technology has been identified which additionally improves switching time by up to 10%. This advanced concept is based on a more efficient usage of high-polar materials and Super Low Viscous (SLV) compounds and simultaneous reduction of less efficient materials.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.136-139
• /
• 2003

We studied the nematic liquid crystal (NLC) aligning capabilities using the new alignment material of a-C:H thin film as working gas at 30W rf bias condition. A high pretilt angle of about $5^{\circ}$ by ion beam(IB) exposure on the a-C:H thin film surface was measured. A good LC alignment by the IB alignment method on the a-C:H thin film surface was observed at annealing temperature of $250^{\circ}C$, and the alignment defect of the NLC was observed above annealing temperature of $300^{\circ}C$. Consequently, the high LC pretilt angle and the good thermal stability of LC alignment by the IB alignment method on the a-C:H thin film surface as working gas at 30W rf bias condition can be achieved.

• Journal of Powder Materials
• /
• v.24 no.5
• /
• pp.370-376
• /
• 2017

In this study we manufacture a Ni-Cr-B-Si +WC/12Co composite coating layer on a Cu base material using a laser cladding (LC) process, and investigate the microstructural and mechanical properties of the LC coating and Ni electroplating layers (reference material). The initial powder used for the LC coating layer is a powder feedstock with an average particle size of $125{\mu}m$. To identify the microstructural and mechanical properties, OM, SEM, XRD, room and high temperature hardness, and wear tests are implemented. Microstructural observation of the initial powder and LC coating layer confirm the layer is composed mainly of ${\gamma}-Ni$ phases and WC and $Cr_{23}C_6$ carbides. The measured hardness of the LC coating and Ni electroplating layers are 653 and 154 Hv, respectively. The hardness measurement from room up to high temperatures of $700^{\circ}C$ result in a hardness decrease as the temperature increases, but the hardness of the LC coating layer is higher for all temperature conditions. Room temperature wear results show that the wear loss of the LC coating layer is 1/12 of the wear level of the Ni electroplating layer. The measured bond strength is also greater in the LC coating than the Ni electroplating.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.398-398
• /
• 2007

The Liquid Crystal (LC) alignment uniformity is very important in LC devices. The alignment mechanism of LC molecules on a rubbed polyimide (PI) surface is very important for both LC fundamental research and application. So, Generally a rubbing method to align LC has been widely used to mass-produce LCD panels. But because rubbing method is contact method between rubbing fabric and indium-tin-oxide glass or flexible substrate, rubbing method has some defects, such as the electrode charges and the creation of contaminating particles. Thus we strongly recommend a non-contact alignment technique for getting rid of some defects of rubbing method. Most recently, the LC aligning capabilities achieved by ion-beam exposure on the organic and nonorganic thin film surface have been reported successfully. In this research, we studied the tilt angle generation and electro-optical performances for a NLC on homeotropic polyimide surfaces with ion-beam exposure. The LC aligning capabilities of a nematic liquid crystal (NLC) on a homeotropic PI surface using a new ion-beam method were studied. On the homeotropic PI surface, the tilt angle of the NLC by exposure ion-beam had a tendency to decrease as increased ion-beam energy density. And, on the homeotropic PI surface, the alignment character of the NLC with respect to ion-beam energy was good. And we achieved satisfactory result for EO character.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.8
• /
• pp.724-728
• /
• 2005

Electro-optic characteristics of reflective hybrid aligned liquid crystal (LC) cell driven by fringe field using a nematic LC with positive dielectric anisotropy have been studied. Optimized optical configurations are achieved by using a single polarizer, half-wave film and a cell with quarter-wave retardation. The simulation results shows an optimum cell retardation of $0.30{\mu}m$. This value may allow a practical cell gap larger than $3{\mu}m$, which makes it easy to control in the manufacturing process. Furthermore, this LC cell with optimized cell parameters shows low wavelength dispersion and the contrast ratio greater than 5 over exists about $100{\circ}$ in vertical direction and $160{\circ}$ in horizontal direction. Also, when using the LC with positive dielectric anisotropy rather than negative dielectric anisotropy, the display shows low power consumption and fast response time.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.1
• /
• pp.59-64
• /
• 2004

We have fabricated the polymer dispersed liquid crystal (PDLC) cell where a control of phase separation is very important. The factors to influence the phase separation are mixing ratio of LC and polymer, curing temperature and UV intensity. In this paper, we inspected the change of a phase separation as a function of curing temperature for the mixture of E7 and. NOA65 with different ratios. When the LC concentration is less than polymer such as LC:NOA65 = 40:60wt％, the PDLC cell is influenced strongly by the curing temperature. However, when the LC concentration is much less than polymer such as LC:NOA65 = 80:20wt％, it is influenced slightly by the curing temperature. The reason is because the mixture shows upper critical solution temperature behavior and therefore it is important to know the behavior of phase separation as a function of curing temperature of the mixture.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.301-301
• /
• 2008

Ion beam (IB)-induced alignment of inorganic materials has been investigated intensively as it provides controllability in a nonstop process for producing high-resolution displays[1][2]. LC orientation via ion-beam (IB) irradiation on the nitrogen doped diamond like carbon (NDLC) thin film deposited by physical deposition method-sputtering was embodied. The NDLC thin film that was deposited by sputter showed uniform LC alignment at the 1200eV of the ion beam intensity. The pretilt angle of LC on NDLC thin films was measured with various IB exposure time and angle. The maximum pretilt angle were showed with IB irradiation angle of $45^{\circ}$ and exposure time of 62.5 sec, respectively. To show NDLC thin film stability in high temperature, thermal stability test was proceeded. The uppermost of the thermal stability of NDLC thin film was $200^{\circ}C$. In this investigation, the electro-optical (EO) characteristics of LC on NDLC thin film were measured.

• Mass Spectrometry Letters
• /
• v.2 no.2
• /
• pp.37-40
• /
• 2011

Saccharin is a commonly used artificial sweetener in foodstuffs. However, for its carcinogenic dispute, it has been regulated by government bodies. In this study, isotope dilution mass spectrometry (ID-MS) was introduced for the accurate quantification of saccharin. To employ ID-LC/MS, we obtained its isotope analogue, $^{13}C_1$-sodium saccharin, by customized synthesis. Samples were spiked with $^{13}C_1$-sodium saccharin and analyzed with LC/MS in negative mode. Chromatographic conditions were optimized for the adequate chromatographic retention and separation of saccharin with a $C_{18}$ column. MS was operated with electrospray ionization by the selected ion monitoring (SIM) mode of $[M-H]^-$ for saccharin (m/z 182) and $[M-Na]^-$ for its isotope analogue (m/z 183). To validate the ID-LC/MS method for accurate measurement, we prepared a batch of a candidate material by sortifying quasi-tea-drinks with saccharin and analyzed samples gravimetrically fortified in various levels of concentration. The repeatability and reproducibility of this method was tested by analyzing the reference material. Result show that ID-LC/MS is a reliable method for the quantitative analysis of saccharin.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.399-400
• /
• 2008

The light efficiency of fringe-field switching (FFS) mode when using a liquid crystal (LC) with positive dielectric anisotropy was found to be dependent on the magnitude of dielectric anisotropy, such that the lower dielectric anisotropy, the higher. We studied out not only light efficiency but also response time according to dependence on the magnitude of dielectric anisotropy. Rising and decay time became fast and slow respectively according to decreasing the magnitude of dielectric anisotropy. This paper investigates electro-optical characteristic of FFS mode using LC with a positive dielectric anisotropy dependent on the magnitude of dielectric anisotropy of the LC.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.5
• /
• pp.427-431
• /
• 2006

We have studied electro-optic characteristics of reflective $45^{\circ}$ twisted nematic liquid crystal display which implement the new LC orientation using of in-cell retarder film. For the embodiment of reflective liquid crystal display, essentially the optic compensation films was always needed and attached to the outside of glass substrate. In our study, these optic compensation film were not employed in reflective LC cell. On other hand we have employed the in-cell retarder to substitute the optic compensation film and were able to orient the LC molecules using this in-cell retarder. So we have developed the reflective LC cell that has good optical performances without any additional coating process on the in-cell retarder.