• The KIPS Transactions:PartC
• /
• v.12C no.6 s.102
• /
• pp.793-798
• /
• 2005

We focus on the RP (Rendezvous Point) system model in the multicast network based on BcN (Broadband Convergence Network) integrating broadcasting, telecommunication and Internet with one. Based on the condition multiple queues with different service and single server, when the arrivals tome in group with the site of the group geometrically distributed, we define the relationship between incoming arrival rate and corresponding buffer size. We also investigate the Profit according to both Service Provider and Network Operator Then we make a decision whether a new service request is accepted or not based on given interning rate range.

• Journal of the Korean Society of Visualization
• /
• v.7 no.2
• /
• pp.28-34
• /
• 2010

Two turbulent jet with different sinusoidal nozzle exit configurations of in-phase and $180^{\circ}$ out-of-phase were investigated experimentally using a smoke-wire method and a hot-wire anemometry. Mean velocity and turbulence intensity were measured at several downstream locations under $Re_D\;=\;5000$. For the case of in-phase nozzle configuration, the length of potential core exhibits negligible difference with respect to the transverse locations (0, $\lambda/4$ and $\lambda/2$), similar to that of a plane jet. On the other hand, a maximum difference of 30% in the potential-core length occurs for the $180^{\circ}$ out-of-phase configuration. The spatial distributions of turbulence intensities also show significant difference for the nozzle of $180^{\circ}$ out-of-phase, whereas non-symmetric distribution is observed in the near-exit region(x/D = 1) for the in-phase sinusoidal nozzle jet. Compared to a slit planc jet, the sinusoidal nozzle jets seem to suppress the velocity deficit as the flow goes downstream. The sinusoidal nozzle jet was found to decrease turbulent intensity dramatically. The flow visualization results show that the flow characteristics of the sinusoidal nozzle jet are quite different from those of the slit plane jet.

• Journal of electromagnetic engineering and science
• /
• v.11 no.2
• /
• pp.83-90
• /
• 2011

In this paper, we present the design method for a low-pass type inverter, which can effectively suppress the spurious response associated with band-pass filters. The inverter has a length of ${\lambda}/4$ and employs not only a stepped-impedance configuration but also asymmetrical and bending structures in order to improve frequency selectivity and compactness. The inverter is applied as an impedance/admittance inverter to the ultra-wideband (UWB) band-pass filter. The UWB band-pass filter configuration is based on a stub band-pass filter consisting of quarter-wavelength impedance inverters and shunt short-circuited stubs ${\lambda}/4$ in length. The asymmetrical stepped-impedance low-pass type inverter improves not only the spurious responses, but also the return loss characteristics associated with a UWB band-pass filter, while a compact size is maintained. The UWB band-pass filter using the proposed inverters is fabricated and tested. The measured results show excellent attenuation characteristics at out-band frequencies, which exceed 18 dB up to 39 GHz. The insertion loss within the pass-band (from 3.1 to 10.6 GHz) is below 1.7 dB, the return loss is below 10 dB, and the group delay is below 1 ns.

• Journal of the Korean Chemical Society
• /
• v.36 no.1
• /
• pp.38-43
• /
• 1992

The Hammett's substituent constants were interpreted for substituted stilbenes by HMO method. The appropriate quantum chemical indices are chosen as independent contribution of the inductive and the resonance effects for substituent constants. It has been found that theoretical values, ${\sigma}_p{^{th}}$, defined as sum of the net charge, self atom polarizability and difference in HOMO energy between substituted- and unsubstituted-stilbenes, correlated with experimental Hammett's substituent constants. The dipole moments were found to be correlated with differences in ${\sigma}_p{^{th}}$ between two substituents for disubstituted stilbenes. It has been also found that transition optical spectra, ${\lambda}_{max}$ of the substituted stilbenes depend on difference between the HOMO and the LUMO energy as expected.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.6
• /
• pp.23-29
• /
• 2013

In this paper, pure $I_{ph}$ and hybrid carbon nanotube reinforced $I_{ph}$ were sintered using the SPS(spark plasma sintering) method for high densification. A nanosecond laser (${\lambda}=1063nm$, ${\tau}P=10ns$) and a femtosecond laser (${\lambda}=1027nm$, ${\tau}P=380fs$) were installed on an optical system for the micromachining test. The ablation characteristics of the pure $I_{ph}$ and CNT/$I_{ph}$ composites, such as thermal effect and ablation depth, were investigated using FE-SEM and a confocal microscope device. Laser machining results for the two mating materials showed improved performances: CNT/$I_{ph}$ composites showed good surface morphology of hole drilling without a melting zone due to the composites' high thermal properties; also, the ablated depth of CNT/$I_{ph}$ was higher than that of pure $I_{ph}$.

• Journal of Institute of Control, Robotics and Systems
• /
• v.15 no.2
• /
• pp.148-154
• /
• 2009

In this paper, an embedded Kalman filter for a time-delayed controller is designed on an FPGA to estimate accelerations of the robot arm. When the time-delayed controller is used as a controller, the inertia estimation along with accelerations is needed to form the control law. Although the time-delayed controller is known to be robust to cancel out uncertainties in the nonlinear systems, performances are very much dependent upon estimating the acceleration term ${\ddot{q}}(t-{\lambda})$ along with inertia estimation ${\hat{D}}(t-{\lambda})$. Estimating accelerations using the finite difference method is quite simple, but the accuracy of estimation is poor specially when the robot moves slowly. To estimate accelerations more accurately, various filters such as the least square fit filter and the Kalman filter are introduced and implemented on an FPGA chip. Experimental studies of following the desired trajectory are conducted to show the performance of the controller. Performances of different filters are investigated experimentally and compared.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.141-144
• /
• 2003

This study proposes ZnO thin film as a piezoelectric material for SAW (surface acoustic wave) filter. The ZnO thin film with thickness $2.6{\mu}m$ was deposited (0001)-oriented sapphire by RF magnetron sputtering technique. IDTs (inter-digital transducers) electrodes were patterned upon SAW filter mask with solid finger structure unapodized using lift-off method on ZnO piezoelectric thin film. SAW propagation velocity was measured with the center frequency by HP 8753C network analyzer. A fabricated ZnO SAW filter exhibited a high propagation velocity of 5433 $^m/s$ and relatively insertion loss of -53.391dB at $\lambda=80{\mu}m$. The side-lobe attenuation of the center frequency was about 17dB. When the wavelength was $80{\mu}m$ $(\lambda/4=20{\mu}m)$, the center frequency was 67.907 MHz. $k^2$ (electromechanical coupling coefficient) was 15.84 %.

• YAKHAK HOEJI
• /
• v.36 no.4
• /
• pp.370-378
• /
• 1992

A simple and sensitive high performance liquid chromatographic method to quantitate ${\alpha}-keto$ acids in serum and urine was investigated. ${\alpha}-Keto$ acids react with 1,2-diamino-4,5-methylenedioxybenzene (DMB) in the presence of 2-mercapto-ethanol and sodium hydrogen sulfite to form highly fluorescent derivatives, substituted 6,7-methylenedioxyquinoxalinol. The derivatization procedure was performed in water bath at $100^{\circ}C$, and completed within 50 min. By the use of a reversed-phase column and multi-step gradient with two solvents, a mixture containing twelve of these derivatives were efficiently resolved within 35 minutes. The optimal wavelengh of the fluorescence detector are ${\lambda}_{ex}=364\;nm$ and ${\lambda}_{em}=445\;nm$. The quantitation of the individual ${\alpha}-Keto$ acids was reproducible with relative standard deviation of $3.0{\sim}7.9%$ and had a detection limits of $10{\sim}60$ fmol, except for p-hydroxyphenylpyruvic acid (960 fmol).

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.30 no.4
• /
• pp.300-306
• /
• 2019

Transmission cross section(TCS) is described analytically as $2G{\lambda}^2/4{\pi}$ irrespective of the aperture shapes for various transmission resonant apertures, such as small ridged circular or H-shaped, U-shaped, or Jerusalem cross-shaped apertures in an infinite thin conducting plane. The proposed expression is validated by comparison with the numerical results obtained from the method of moments(MOM). The TCS characteristics of the transmission resonant cavity structure in a thick conducting plane are also studied and the equivalence between the two small aperture structures is reported from the viewpoint of transmission efficiency.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.6
• /
• pp.225-228
• /
• 2005

We have grown the long persistent $SrAl_2O_4:Eu^{2+},\;Dy^{3+}$ phosphor single crystal by Verneuil method. The obtained single crystals were long persistent phosphorescence peaking at ${\lambda}=520nm$ with a size of about 5 mm diameter, 55 mm length. The melting temperature of $SrAl_2O_4:Eu^{2+},\;Dy^{3+}$ measured $T_{mp}=1968^{\circ}C$. The optimum composition was $SrCO_3:Al(OH)_3:Eu_2O_3:Dy_2O_3$ = 1 : 2 : 0.015 : 0.02. Flow rate of $H_2:O_2$ is about 4 : 1. Growthing rate is about 5 mm/hr. The spectra of the phosphorescence from the crystals are quite similar to those obtained with sintered powders used for luminous pigments. The crystalline structure of long persistent $SrAl_2O_4:Eu^{2+},\;Dy^{3+}$ phosphor single crystal was determined by X-ray diffraction.