• Journal of Power Electronics
• /
• v.17 no.4
• /
• pp.923-932
• /
• 2017

This paper proposes a novel scheme which can compensate the common-mode voltage (CMV) for five-level active neutralpoint clamped (5L-ANPC) inverters, which is based on modifying the space vector pulse width modulation (SVPWM) and adding an auxiliary leg to the inverter. For the modified SVPWM, only the 55 voltage vectors producing low CMV values among the 125 possible voltage vectors are utilized, which varies over the three voltage levels of $-V_{dc}/12$, 0 V, and $V_{dc}/12$. In addition, the compensating voltage, which is injected into the 5L-ANPC inverter system to cancel the remaining CVM through a common-mode transformer (CMT) is generated by the additional NPC leg. By the proposed method, the CMV of the inverter is fully eliminated, while the utilization of the DC-link voltage is not decreased at all. Furthermore, all of the DC-link and flying capacitor voltages of the inverter are well controlled. Simulation and experimental results have verified the validity of the proposed scheme.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.4
• /
• pp.103-108
• /
• 2004

Carbon fiber reinforced composites(CFRP) were fabricated with phenolic resin matrix by hot press molding, and its surface was modified by the ion-assisted reaction process. When we tested the friction coefficient and wear rate variation and observed the effect of fibers with respect to friction and wear characteristics, the amount of pitch based carbon fiber was 45wt% and the average friction coefficient was the lowest at 0.12. When the amount of ion-irradiation was $1\times10^{l6}ions/cm^2$, the friction coefficient of the composites was about 0.12 and the wear mode was stable, whereas, the friction coefficient of the non-treated composites was about 0.16 and the wear mode was very unstable. But if the amount of ion-irradiation was $5\times10^{l6}ions/cm^2$$1\times10^{l6}ions/cm^2$ion-irradiation case.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.12
• /
• pp.1025-1031
• /
• 2000

An ultrasonic linear motors consist of a slider and an ultrasonic vibrator which generates an elliptical oscillations. The ultrasonic linear motors mainly consist of an ultrasonic vibrator which generates elliptical oscillations. The ultrasonic linear motor fabricated in this paper was the use of the 1st longitudinal(L1) and 4th bending vibrations(B4). In order to low driving voltage and improve the life time of the ultrasonic motor, we used stacked piezoceramics. Stacked piezoceramics are adhered to aluminum elastic material. The finite element method was used to optimize dimension of ultrasonic vibrator and direction of vibratory displacement. As a result of estimating the characteristics of the ultrasonic linear motor, no-load velocity was 0.204[m/s] when applied voltage was 70[ $V_{rms}$] in resonance frequency.y.

• Proceedings of the KIEE Conference
• /
• 1999.07b
• /
• pp.903-905
• /
• 1999

In this paper, a novel sliding surface is proposed by defining a novel virtual state. This sliding surface has nominal dynamics of an original system and makes it possible that the Discrete-Time Sliding Mode Control(DSMC) technique is used with the various types of controllers. Its design Is based on the augmented system whose dynamics have a higher order than that of the original system. The reaching phase is removed by using an initial virtual state which makes the initial sliding function equal to zero.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.93-96
• /
• 2004

An ultrasonic linear motor was composed of a slider and a stator vibrator including piezoelectric material and elastic material. The ultrasonic linear motors mainly consist of an ultrasonic vibrator which generates elliptical oscillations. L1-B4 ultrasonic linear motor use longitudinal and bending multi-vibration. In order to design stators which has high efficiency and driving characteristics, The finite element method was used to optimize dimension of ultrasonic vibrator and direction of vibratory displacement. stator vibrator of respectively width 3, 5, 7[mm] was fabricated and experimented. as results When width was 5[mm], the driving characteristics was good.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.6 no.1
• /
• pp.1-5
• /
• 2001

The potential use of spin filter device to retain Propionibacterium acidipropionici in the bioreactor under continuous mode of fermentation, and improve acid productivity, was examined. The yield of propionic acid based on lactose concentration was 51% in batch and 54% in continuous (dilution rate = 0.05 h(sup)-1) operation. The yield in continuous fermentation with cell retention using spin filter of 10 micron size (dilution rate = 0.05 h(sup)-1) was even higher at 70% (w/w). The volumetric productivity under batch and continuous mode of operation were 0.312g L(sup)-1 h(sup)-1 and 0.718g L(sup)-1 h(sup)-1 respectively. Continuous fermentation with cell retention demonstrated even higher volumetric productivities at 0.98g L(sup)-1 h(sup)-1 with out clogging problems. It could be used for utilization of cheese whey to produce propionic acid at higher yield and productivities.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05d
• /
• pp.432-437
• /
• 1996

The observed characteristics of magnetic oscillations in L-H transition and disruption are described. Two kinds of MHD magnetic probes are used in order to cover broadband frequency range from 1.3 kHz to 300 kHz in the H-mode. Depending on the probe's position and frequency, different characteristics are observed. Precursor like oscillation in L-H transition, and the difference between sawtooth and ELM are discussed. All disruptions during the current rising phase are related with m＝2 or m＝3 mode. Different disruption characteristics for different operation conditions could be found in the MHD probes.

• Journal of Korean Society of Transportation
• /
• v.12 no.3
• /
• pp.29-47
• /
• 1994

Although subway system continues to be the backbone of transportation systems in a city like Seoul, there will still be areas across the city where subway services are not avaliable. Interest has steadily grown to fill this missing routes in overall urban transportation system. Light Rail Transit (L.R.T) system has been recently thought to be an appropriate mode of transportation by businessmen, professionals and transportation industry. In this regards, the purpose of this study is to explore whether L.R.T can be a feasible form of urban rail mode in the context of Seoul. First, the study develops the mathematical models to derive optimum route networks and stations. Integer Programming is employed to determine whether alternative routes are financially viable from the viewpoint of revenue maximization principles. Second, mathematical models developed are applied to Yoido area in order to examine the validity of model structures. The models constructed turns out be capable of handling alternative routes and stations. Application of models are successfully carried out to derive financially feasible set of routes and stations.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.5
• /
• pp.349-356
• /
• 2021

Permanent magnet synchronous motors are mainly used in the traction of electric vehicle and home application products including air-conditioners and refrigerators. For sensorless control without rotor position sensors, I-F control is applied for initial starting at low speeds, and mode is changed to sensorless control when the rotor speed is sufficiently accelerated for estimating rotor position. When the mode is changed to the sensorless control from the open-loop starting, the initial integral value of the speed controller should be considered by load condition; otherwise, the transition to sensorless control may fail. The sensorless transfer algorithm of PM synchronous motor based on load condition for smooth transition is proposed. The performance of the proposed sensorless transfer algorithm was verified by experiments.

• Journal of Software Assessment and Valuation
• /
• v.16 no.1
• /
• pp.55-63
• /
• 2020

Lasers for optical broadband communication systems should have excellent frequency selectivity and modal stability. DFB lasers have low lasing frequency shift during high speed current modulation. In this paper, when a refractive index grating and a gain grating are simultaneously present in a DFB laser having a wavelength of 1.55 ㎛, the dielectric film is coated so that reflection does not occur on the right mirror surface, so that ρ_r=0. For the first mode, which requires a minimum gain at the threshold, the beam distribution of the oscillation mode in the longitudinal direction and the radiated power ratio P_l/P_r were analyzed and compared for the cases of the phase of ρ_l=π and π/2. If the phase of ρ_l=π, in order to obtain a low threshold current and high frequency stability, κL should be greater than 8. In the case of the phase of ρ_l=π/2, for low threshold current, κL is necessary to be 1.0, where the oscillation frequency coincides with the lattice frequency. DFB lasers with an anti-reflection coated mirror have excellent mode selectivity than 1.55um DFB lasers with two mirror facets