• Journal of the Korean Wood Science and Technology
• /
• v.44 no.4
• /
• pp.477-493
• /
• 2016

A single process using hot water (0% green liquor) and green liquor (GL) was investigated for pre-pulping extraction on two types of raw material. The GL was applied at different alkali charges of 0-5% on a dry wood weight basis. The extractions were performed at an H-factor 900 at $180^{\circ}C$. The 0% and 3% GL extraction detected acetic acid (AA) at 10.02 and $9.94g/{\ell}$, extracts derived from hardwood, 2.46 and $3.76g/{\ell}$, extracts derived from softwood, respectively. The single liquid-liquid extraction (LLE) was studied using tri-n-alkylphosphine oxide (TAPO). Response surface methodology (RSM) was employed as an efficient approach for predictive model building and optimization of AA recovery conditions. The extraction of AA was evaluated with a three-level factorial design. Three independent variables, pH (0.5-3.5), temperature ($25-65^{\circ}C$), and residence time (24-48 min) were investigated. Applying the RSM models obtained, the optimal conditions selected of extracts derived from hard- and softwood with a 3% GL were approximately pH 1.4, $26.6^{\circ}C$, 43.8 min and approximately pH 0.7, $25.2^{\circ}C$, 24.6 min, respectively. The predicted and experimental values of AA recovery yield were similar whilst sugar retention was 100%.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.5
• /
• pp.429-438
• /
• 2010

In this study, effect of carbon source on the hydrolytic ability of the enzyme from Fomitopsis pinicola, a brown rot fungi, for lignocellulosic biomass were examined on two lignocellulosic biomasses (rice straw and wood) without any pretreatment. Cellulase activities of crude enzyme from F. pinicola, which was cultured on softwood mixture as a carbon source, were 19.10 U/$m{\ell}$ for endo-${\beta}$-1,4-gulcanase (EG), 36.1 U/$m{\ell}$ for ${\beta}$-glucosidase (BGL), 7.27 U/$m{\ell}$ for cellobiohydrolase (CBH), and 7.12 U/$m{\ell}$ for ${\beta}$-1,4 xylosidase (BXL). Softwood mixture as a carbon source in F. pinicola comparatively enhanced cellulase activities than rice straw. The optimal pH and temperature of the cellulase was identified to pH 5 and $50^{\circ}C$for the hydrolysis of rice straw. Under these condition rice straw was hydrolyzed to glucose by the cellulase up to $32.0{\pm}3.1%$ based on the glucan amount of the rice straw for 72 h, while the hydrolytic capability of commercial enzyme (Celluclast 1.5${\ell}$) from rice straw to glucose was estimated to $53.7{\pm}4.7%$ at the same experimental condition. In case of addition of Tween 20 (0.1% w/w, substrate) to the cellulase the hydrolysis of rice straw to glucose was enhanced to $38.1{\pm}2.0%$.

• Journal of Korean Society of Forest Science
• /
• v.79 no.3
• /
• pp.255-259
• /
• 1990

To investigate relative flammability in flaming combustion among 10 softwoods and 10 hardwoods, oxygen indices were determined for flat-grained sapwoods through Up and Down method following oxygen index test of ASTM D 2863-77. Oxygen index ranged from 21.0 for Pinus strobus to 28.2 for Larix gmelinii var. principis-ruprechtii in softwoods and from 20.7 for Populus davidiana to 27.6 for Quercus acntissima in hardwoods, which indicates Larix gmelinii var. principis-ruprechtii and Quercus acutissima being ranked first in inflammability and Pinus strobus and Populus davidiana being the least in fire resistance by softwood and hardwood because highly flammable materials are likely to have a low oxygen index.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.4
• /
• pp.6-12
• /
• 1998

Test results of domestic softwood lumber were presented to examine the notch effect of beams and compare to present AIJ(Architecture Institute of Japan) formula in notched wood member especially positioned in bottom side (tension side) of a beam. Notched lumber was tested under following condition : each specimen supported simply, and subjected to third-point loading at points of 1/3 of the span length. Notch was located opposite side to loading direction and notch depth were 1/6, 1/4, 1/3 of beam depth. Deflection and load were measured by digital dial guage each in 25kgf increment. Bending test results were as follows; Mpro/Mmax range (proportional and maxium bending moment ratio in notched beam) was 0.5 - 0.65. It was considered that maxium bending moment was about 1.5 times to proportional bending moment in notched beam and showed same tendency in the test result of ordinary wood specimens. AU standard formula for the tension side notch, Mmat = 0.6 ${\times}$ (Zo $\sigma$), the constant 0.6 was suitble for notch ratio(notch depth to beam depth) 1/6, but this ratio for 1/4, and 1/3 was not. So it is preferable to accept smaller value than 0.6 for notch ratio more than 1/3. These experiment results showed critical effect in tension side notched wood beam especially in greater than notch ratio 1.3 of wood beam. From the above results, it is recommened to revise design formula adoptable to domestic wood constructon member with tension side notched member.

• FLOWER RESEARCH JOURNAL
• /
• v.17 no.4
• /
• pp.262-265
• /
• 2009

This study was conducted to find out a proper cutting time as related with a growth pattern for the mass propagation of Corylopsis coreana, which is one of the Korean endemic plant. New shoots began to grow in early April soon after end of blooming time and grew rapidly until the end of June. Shoot growth became dull after June and stopped in early September, showing a typical primary growth curve of temperate deciduous trees which show only one flush of growth throughout an annual growth cycle. The moisture content of shoot was the highest in an early growing season of May, and decreased with shoot maturity. Moisture content of cuttings taken on June 20 was 71.2%. Rooting was better in softwood cuttings than in hardwood cuttings. The highest value of rooting percentage was obtained in cuttings taken on June 20.

• Korean Journal of Plant Resources
• /
• v.14 no.2
• /
• pp.102-107
• /
• 2001

This study was carried out to explore for the possibility of recycling the pine wood sawdusts for the substrate for enokitake (Flammulina velutipes) cultivation. The wood species of sawdusts cultivated for enokitake mushroom were identified mostly as hard pine (Pinus spp.). Distribution of enokitake hyphae was restricted to ray parenchymas and tracheids exposed to fungi. Nevertheless, degree of cell wall degradation by enokitake was slight. Light microscopic observation showed the thinning of secondary cell wall in some tracheids. Under polarized microscopy the 1()ss of birefringence was observed only in a few latewood tracheids. All the middle lamella remained intact. The present work showed clearly that pine sawdusts used as substrate for enokitake cultivation held enough cell wall materials for mushroom cultivation. The relative resistance of softwood cell walls against enokitake fungus was also discussed.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.4
• /
• pp.450-457
• /
• 2020

Single pellet press technology allows for fast, low-cost, and small-scale tests to investigate pelletizing characteristics. We estimated proper compression ratios for five Korean domestic wood species through predicted relationships between pelletizing pressure P_x and compression ratio based on experimental data obtained from a single pellet press unit. The pressures required to obtain a 6-mm-diam pellet of density 1200 kg/㎥ were estimated as 111 MPa for Populus davidiana, 133 MPa for Robinia pseudoacacia, 136 MPa for Quercus mongolica, 97 MPa for Pinus densiflora, and 127 MPa for Pinus rigida. On the basis of these pressures, we estimated proper compression ratios to be within the range 7.676-8.410 for these species, and we found the compression ratios needed for hardwood species to be somewhat higher than those needed for softwood species to obtain the pellet density of 1200 kg/㎥.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.30 no.3
• /
• pp.57-64
• /
• 2012

When papers each made with sea-algae pulp 1%, 5% and soft, hard wood pulp were aged for 12days. Paper made with soft wood pulp is 30% loss of folding endurance, made with hard wood pulp is 50% loss of folding endurance. On the other, papers each made with 9% sea-algae pulp and soft, hard wood pulp were 18% loss of folding endurance. In the aging test of paper made with different freeness paper made with 300ml CSF, is more effective than 400ml CSF, 500ml CSF.

• Proceedings of the Korean Society of Plant Biotechnology Conference
• /
• 2003.04a
• /
• pp.194-194
• /
• 2003

• Journal of the Korean Society of Tobacco Science
• /
• v.22 no.2
• /
• pp.164-169
• /
• 2000

The reconstituted tobacco leaves(RTL) playa major part in the control of the low density and tar cigarette. Reconstituted tobacco manufactured by the papermaking process has much higher filling power than homogenized tobacco manufactured by slurry and rolling process. Fragile reconstituted tobaccos are liable to lead to small particles detrimental for filling power so they must be properly flexible. This work was conducted to determine the effect of CaCO$_3$ addition in paper-making process on the filling power and the flexibility of the reconstituted tobacco and to obtain the fundamental informations for improving the quality of domestic reconstituted tobacco. We analyzed the wood fiber species, the filler level, the fiber length, the fineness level and observed the surface of the RTL. From the obtained results, we could determine that foreign reconstituted tobacco was manufactured by blending softwood with hardwood and over 8% of calcium carbonate at the addition level. The domestic RTL has much higher fine fiber level by 23.2 % than that of foreign, so the refining treatment process and the condition must be reoptimized for the improvement of RTL quality.