• Korean Journal of Materials Research
• /
• v.23 no.10
• /
• pp.568-573
• /
• 2013

The deformation properties of a TiC-Mo eutectic composite were investigated in a compression test at temperatures ranging from room temperature to 2053 K and at strain rates ranging from $3.9{\times}10^{-5}s^{-1}$ to $4.9{\times}10^{-3}s^{-1}$. It was found that this material shows excellent high-temperature strength as well as appreciable room-temperature toughness, suggesting that the material is a good candidate for high-temperature application as a structure material. At a low-temperature, high strength is observed. The deformation behavior is different among the three temperature ranges tested here, i.e., low, intermediate and high. At an intermediate temperature, no yield drop occurs, and from the beginning the work hardening level is high. At a high temperature, a yield drop occurs again, after which deformation proceeds with nearly constant stress. The temperature- and yield-stress-dependence of the strain is the strongest in this case among the three temperature ranges. The observed high-temperature deformation behavior suggests that the excellent high-temperature strength is due to the constraining of the deformation in the Mo phase by the thin TiC components, which is considerably stronger than bulk TiC. It is also concluded that the appreciable room-temperature toughness is ascribed to the frequent branching of crack paths as well as to the plastic deformation of the Mo phase.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.15 no.10
• /
• pp.860-869
• /
• 2003

Design optimization of the heat sink with 7${\times}$7 square pin-fins is performed numerically using the Computational Fluid Dynamics (CFD) and the Computer Aided Optimization (CAO). In the pin-fins heat sink, the optimum design variables for fin height (h), fin width (w), and fan-to-heat sink distance (c) can be achieved when the thermal resistance ($\theta$$_{j}$) at the junction and the overall pressure drop ($\Delta$p) are minimized simultaneously. To complete the optimization, the finite volume method for calculating the objective functions, the BFGS method for solving the unconstrained non-linear optimization problem, and the weighting method for predicting the multi-objective problem are used. The results show that the optimum design variable for the weighting coefficient of 0.5 are as follows: w=4.653 mm, h=59.215 mm, and c=2.667 mm. In this case, the objective functions are predicted as 0.56K/W of thermal resistance and 6.91 Pa of pressure drop. The Pareto optimal solutions are also presented.re also presented.d.

• Clinical and Experimental Reproductive Medicine
• /
• v.40 no.4
• /
• pp.163-168
• /
• 2013

Objective: Preimplantation genetic diagnosis (PGD) is an assisted reproductive technique for couples carrying genetic risks. Charcot-Marie-Tooth (CMT) disease is the most common hereditary neuropathy, with a prevalence rate of 1/2,500. In this study, we report on our experience with PGD cycles performed for CMT types 1A and 2F. Methods: Before clinical PGD, we assessed the amplification rate and allele drop-out (ADO) rate of multiplex fluorescent polymerase chain reaction (PCR) followed by fragment analysis or sequencing using single lymphocytes. We performed six cycles of PGD for CMT1A and one cycle for CMT2F. Results: Two duplex and two triplex protocols were developed according to the available markers for each CMT1A couple. Depending on the PCR protocols, the amplification rates and ADO rates ranged from 90.0% to 98.3% and 0.0% to 11.1%, respectively. For CMT2F, the amplification rates and ADO rates were 93.3% and 4.8%, respectively. In case of CMT1A, 60 out of 63 embryos (95.2%) were diagnosed and 13 out of 21 unaffected embryos were transferred in five cycles. Two pregnancies were achieved and three babies were delivered without any complications. In the case of CMT2F, a total of eight embryos were analyzed and diagnosed. Seven embryos were diagnosed as unaffected and four embryos were transferred, resulting in a twin pregnancy. Two healthy babies were delivered. Conclusion: This is the first report of successful pregnancy and delivery after specific PGD for CMT disease in Korea. Our PGD procedure could provide healthy babies to couples with a high risk of transmitting genetic diseases.

• Design & Manufacturing
• /
• v.13 no.2
• /
• pp.37-43
• /
• 2019

This study conducted a research as to condensation heat transfer friction loss headby using three types of flat micro multi-channel tubes with different processing of micro-fin and number of channels inside the pipes and different sizes of appearances. In addition, identical studies were conducted by using smoothing circular tubes with 5mm external diameter to study heat enhancement factor and pressure drop penalty factor. 1) The friction head loss showed an increase as the vapor quality and mass flux increased. In case of saturation temperature, it shows an increase as it gets lower. These factors are the reason occurring as the lower the saturation temperature is, the higher the density of refrigerant vapor gets. The influence of heat flux is similar as the dryness is low, but as it gets higher, it lowers in heat flux, and as the high temperature of high heat flux, it is a factor that occurs as the density gets lower. 2) RMS error of the in case of friction head loss, it showed to be predicted as 0.45~0.67 by Chisholm, Friedel, Lockhart and Martinelli. 3) As forfriction head loss penalty factor, the smaller the aspect ratio is, the larger the penalty factor gets, and as for the effect of micro-fin, the penalty factor increased because it decreases to the gas fluid the way groove for the refrigerant's flow.

• Journal of Haehwa Medicine
• /
• v.13 no.1
• /
• pp.303-309
• /
• 2004

After treating a patient suffering from metacarpophalangeal joint extension disturbance which is caused by posterior interosseous nerve palsy, some results are gained as follows. The symptom of posterior interosseous nerve palsy is simillar to the it of radial nerve palsy. But posterior interosseous nerve palsy isn't accompany with wrist drop. posterior interosseous nerve palsy is accompany with metacarpophalangeal joint extension disturbance. This symptom is caused by posterior interosseous nerve palsy. Posterior interosseous nerve palsy is correspond to MAMOKBULIN(麻木不仁), SUTONG(手痛), SUGI(手氣) in oriental medicine. The cause of this case on oriental medicine is Deficiency of qi and blood. Treatment which based on cause of oriental medicine-herb medication, acupuncture treatment- have a good effect to patient.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.298-299
• /
• 2008

In this paper, supposed that can measure power quality of bus and can calculate this cost in case electric charges about customer are imposed by each bus. When reflected this in system planning, expected cost proposed following method through sample system. We calculated the nodal cost by OPF(optimal power flow) in system and the drop numbers that happen during year of loads utilizing VSCC. Also calculated BPQC using the disruption numbers. As a result, calculated bus total cost including power quality cost through case study.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.442-447
• /
• 2003

The characteristics of instantaneous wall-surface temperature of impinging plate in case of ultra high pressure injection have been measured and analyzed by using thin film instantaneous temperature probe and ultra high pressure injection equipment. The decreasing rate of temperature was greater in case of higher temperature of impinging plate. Temperature drop was largest at center of piston and it was slight for others. Instantaneous temperature decreases rapidly with increasing injection pressure. But above 2,500bar of injection pressure, the decreasing rates are slightly affected by increasing injection pressure.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1081-1082
• /
• 2006

The more feeding distance of substation is long and travel vehicle increases in feeding section, power supply leaches the limits. And if it exceeds the limit, it causes a serious trouble for train operation. Therefore, it is designed that the number of train increases constantly until 2030. So consistent power supply according to the increasement of vehicle in power system at present Seoul-Pusan high speed railway, regular operation in case of extended feeding occurring accidents in substation, and the least headway scheduled at relevant section and the effects installing compensation facility in case of impossible extended feeding is examined.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.2151-2156
• /
• 2004

In this study, five experiments were carried out, with an orifice located downstream of a fan in case I and upstream distance to the fan in the rest cases(case $II{\sim}$), so as to determine the optimal location of the orifice and reduce the size of airflow measurement device. The resulting flow rate-pressure drop correlations were found to satisfy the limitation of SMACNA standard, which specified an error of ${\pm}7.5%$ based on the real flow rate. The best outcome was achieved with the orifice located midway of the orifice duct 4 times its diameter long.

• Journal of Power Electronics
• /
• v.4 no.2
• /
• pp.87-95
• /
• 2004

A new fast-response high-current clamp DC-DC converter circuit design is presented that will meet the requirements and features of the new generation of microprocessors and digital systems. The clamp in the proposed converter amplifies the current in case of severe load changes and is able to produce high slew rate of output current and capability to keep constant the output voltage. This proposed high-current clamp technique is theoretically loss less, low cost and easy to implement with simple control scheme. This is modified from a basic buck topology by replacing the output inductor with two magnetically coupled inductors. Inductors are difference in inductance, one has large inductance and other has small inductance. The inductor with small inductance will take over the output inductor during fast load transient. It speedup the output current slew rate and reduce the output voltage drop in the case of heavy burden load changes.