• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.146-156
• /
• 2007

In this paper, the TVC actuation test and analysis results for a flexible seal kick motor nozzle are presented. A real-sized test model of KSLV-I kick motor system is applied to water pressurizing TVC tests which investigate the property changes in TVC nozzle expansion and TVC actuation performance against chamber pressure changes. The equipments which are required for TVC actuation tests are briefly explained. The TVC actuation tests are firstly accomplished in static mode, which reveals TVC error characteristics including thrust misalignment, control accuracy, and TVC stroke increase, etc. The properties in frequency domain is given via dynamic tests. These results may play an important role in enhancing the TVC control performance of KSLV-I.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.479-483
• /
• 2012

This paper describes the development status of rocket engine test facility for the performance evaluation of liquid rocket engine of KSLV-II 1st stage. Design specification and composition of rocket engine test facility are suggested based on the design requirements. The results of the basic design of rocket engine test facility will be used as base data for the detail design and construction of rocket engine ground test facility of KSLV-II 75tonf liquid rocket engine.

• Aerospace Engineering and Technology
• /
• v.10 no.1
• /
• pp.98-106
• /
• 2011

This paper is summarized for designing launch vehicle autopilot structure with attitude angle command from guidance algorithm and for evaluating performance of autopilot using launch vehicle six-degree of freedom simulation program. The suggested autopilot has heritage from KSR-III/KSLV-I upper stage autopilot designing experience, and it has two design point. The one is, it must have same performance with KSR-III/KSLV-I upper stage autopilot, the other is, it must be simple autopilot structure and use low number of variable to apply on-board system. It is evaluated the performance using launch vehicle six-degree of freedom simulation program in case of roll maneuvering and no roll control flight condition.

• Aerospace Engineering and Technology
• /
• v.9 no.1
• /
• pp.106-115
• /
• 2010

Because of space limitations, interferences between antennas of the KSLV-I communication systems occur and their effects become worse during all sorts of tests such as the flight test using a light plane. In this paper, coupled signal magnitude is calculated using the FDTD method. The theory of the FDTD, absorbing boundary condition, source input technique, and post processing of data are explained. The calculated coupling factor between two IFAs, which have 2 GHz resonance frequency and placed 5 cm apart, is -12.7 dB. Applied coupling calculation method can be effectively used for KSLV-I performance analysis, subsystem design, antenna arrangement, and communication link budget for the next space launch vehicle.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.189-199
• /
• 2013

This paper summarizes results of second stage attitude control of KSLV-I third flight test. The results show that three axes attitude control at coasting phases of KSLV-I was successfully accomplished by the reaction control system, and pitch and yaw attitude control at thrusting phase where second stage kick motor burns was also normally accomplished by using the thrust vector control system. It is verified that the second stage controller performed successfully for all flight phases regardless of some disturbances due to mass center offset, slag effects, and residual thrust of kick motor. These results may provide an important basis in enhancing domestic technology level of attitude control of launch vehicle.

• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.199-202
• /
• 2005

Separation motion of 1:2 downscaled nose fairing is simulated. In comparison with the experimental results, results of analyses on the separation simulation are verified and the characteristics of nose fairing separation are analyzed. The results shows about 5% analysis error.

• Aerospace Engineering and Technology
• /
• v.4 no.1
• /
• pp.122-128
• /
• 2005

A work breakdown structure of 3-staged launch vehicle has been developed during the preliminary design step of KSLV-I program. In the present paper, the background, the detailed contents, and the total structures of WBS have been studied. The management plan for WBS has been also provided.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.623-626
• /
• 2009

Hanwha Corporation Daejeon Plant have developed apogee Kick Motor of KSLV-I that is the first among nation space launch vehicle for five years from 2003. Now, we are joining in KSLV-II(Korea Space Launch Vehicle-II) project and developing Pyro starter which is turbo pump for the first start-up of liquid propulsion supply.

• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.81-86
• /
• 2013

This article deals with the manufacturing and performance evaluation on the specimen pipes which have large size diameter and thin thickness. This specimen is for LOX main pipe of KSLV-II propulsion feeding system. The material of specimen is alloy 21-6-9. Alloy 21-6-9 has higher strength and better weldability rather than STS-300 class pipes. We found that the specimen using alloy 21-6-9 satisfied the requirement by pressurization tests.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1169-1170
• /
• 2017

Engine System Development Document management system(ESDD) 2.0 has already been operated for systematic engine systems development of KSLV-II. In addition, ESDD 3.0 is under development to manage the documents of before and after engine tests. In this paper, the concept and direction of ESDD 3.0 will be briefly described.