• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.5
• /
• pp.521-530
• /
• 2017

Improving the microstructure of NiO/YSZ is one of several approaches used to enhance the electrical and mechanical properties of an anode support in Solid Oxide Fuel Cells (SOFCs). The aim of the work reported in this paper was to predict the relationship between these microstructural changes and the resulting properties. To this end, modification of the anode microstructure was carried out using different sizes of Poly (Methyl Methacrylate) (PMMA) beads as a pore former. The electrical conductivity and mechanical strength of these samples were measured using four-probe DC, and three-point bend-test methods, respectively. Thermal etching followed by high resolution SEM imaging was performed for sintered samples to distinguish between the three phases (NiO, YSZ, and pores). Recently developed image analysis techniques were modified and used to calculate the porosity and the contiguity of different phases of the anode support. Image analysis results were verified by comparison with the porosity values determined from mercury porosimetry measurements. Contiguity of the three phases was then compared with data from electrical and mechanical measurements. A linear relationship was obtained between the contiguity data determined from image analysis, and the electrical and mechanical properties found experimentally. Based upon these relationships we can predict the electrical and mechanical properties of SOFC support from the SEM images.

• 한국전산유체공학회:학술대회논문집
• /
• 2008.08a
• /
• pp.79.5-80
• /
• 2008

• 한국전산유체공학회:학술대회논문집
• /
• 2008.08a
• /
• pp.73.5-73.5
• /
• 2008

• Proceedings of the KIEE Conference
• /
• 1999.07d
• /
• pp.1824-1826
• /
• 1999

In order to develop key technologies for a kW class for polymer electrolyte fuel cell (PEFC), various membranes (Nafion(112, 115, 117), Dow, Flemion, Gore, and Hanwha), and electrocatalysts (Pt/C, PtNi/C PtNiCo/C and PtRu/C) were used in the fabrication of the MEAs by using transfer printing technique. The effects of the thickness of Nafion membranes, electrocatalysts and the operating conditions (e.g. temperature, reactant gas pressure, and composition) on the performance of the MEA were investigated in the PEFC single cell($O_2/H_2$, and Air/$H_2$ cell). The performances of the MEAs for $O_2/H_2$ and Air/$H_2$ cells has been evaluated.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.64.1-64.1
• /
• 2010

In this study, the energy and economic analysis of KIER Zero Energy Solar House (KIER ZeSH) was carried out. KIER ZeSH was designed and constructed in the end of 2009 for the purpose of more than 70% energy self-sufficiency in total load as well as less than 20% of additional construction cost. The several building energy conservation technologies like as super insulation, high performance window, wast heat recovery system, etc and renewable energy system. The renewable heating and cooling system is a kind of solar thermal system combined with geo-source heat pump as a back-up device. The capacity of 3.15kW solar BIPV system was also installed on the roof. The measurement by monitering system of ZeSH was conducted for one year from November 2009 to October 2010. The energy self-sufficiency and economic analysis were conducted based on the this monitering result. As a result, the energy self sufficiency is about 83% which is higher than that of the target and the payback period is 11 years.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.6
• /
• pp.1651-1655
• /
• 2013

Anion exchange membranes for a vanadium redox flow battery (VRB) were prepared by pore-filling on a PE substrate with the copolymerization of vinylbenzyl chloride (VBC) and glycidyl methacrylate (GMA). The ion exchange capacity, water uptake and weight gain ratio were increased with a similar tendency up to 65% of GMA content, indicating that the monomer improved the pore-filling degree and membrane properties. The vanadium ion permeability and open-circuit voltage were also investigated. The permeability of the VG65 membrane was only $1.23{\times}10^{-7}\;cm^2\;min^{-1}$ compared to $17.9{\times}10^{-7}\;cm^2\;min^{-1}$ for Nafion 117 and $1.8{\times}10^{-7}\;cm^2\;min^{-1}$ for AMV. Consequently, a VRB single cell using the prepared membrane showed higher energy efficiency (over 80%) of up to 100 cycles compared to the commercial membranes, Nafion 117 (ca. 58%) and AMV (ca. 70%).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.155-159
• /
• 2003

The preparation and luminescence characterization of yttrium oxide doped with trivalent europium phosphors by sol-gel method have been investigated. Aqueous metal nitrate solution was mixed with EDTA which was chosen by the most suitable material of sol-gel formation one of appled various chelating agents. we noticed that the samples when are heated with EDTA at a temperature of $100^{\circ}C$ for 1hrs, produced brownish and crisp powders due to condensation reaction on decomposition, dehydration and formation of sol-gel. Hence, when the powder pre-heated was then heated at $1200^{\circ}C$ for 3hrs in atmosphere, the luminescence characterization of resultant $Y_{2}O_{3}:Eu^{3+}$ phosphor was enhanced upto maximum 30% significantly than conventional method through increasing porous region and decreasing particle sizes.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.04a
• /
• pp.151-154
• /
• 2003

The synthesis and luminescent properties of trivalent europium activated gadolinium oxide red phosphors by sol-gel process have been investigated. Aqueous metal nitrate solution was mixed with EDTA which was chosen by the most suitable material of sol-gel formation as chelating agents. We noticed that the samples when are heated with EDTA at a temperature of $100^{\circ}C$ for lhrs, produced brownish and crisp powders due to condensation reaction on decomposition, dehydration and formation of sol-gel. Hence, when the powder pre-heated at about $100^{\circ}C$ was then heated at $1200^{\circ}C$ for 3hrs in atmosphere, the luminescence properties of resultant $Gd_{2}O_{3}:Eu^{3+}$ phosphor was measured by SEM, FT-IT and brightness intensity was shown 20% higher than those prepared by conventional method and by other chelating agent.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05c
• /
• pp.63-66
• /
• 2002

Bi-layer Mo films were deposited on sodalime glass substrates using DC magnetron sputtering. As the gas pressure and power density, the resistivity varied from $1.5{\times}10^{-5}$ to $4.97{\times}10^{-4}{\Omega}{\cdot}cm$. Furthermore, stress direction yielded compressive-to-tensile transition stress curves. The microstructure of the compressive stress films which had poor adhesion consists of tightly packed columns, but of the tensile-stressed films had less dense structure. Under all gas pressure conditions, Mo films exhibited distinctly increasing optical reflection with decreasing gas pressure. The expansion of (110) peak width with the gas pressure meant the worse crystalline growth. Also, The highest efficiency was 15.2% on 0.2 $cm^2$. The fill factor, open circuit voltage and short circuit current were 63 %, 570 m V and 42.6 $mA/cm^2$ respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.116-119
• /
• 2002

A different route to the synthesis of $Eu^{3+}$ - activated matrices such as $YAlO_{3}$ and $GdAlO_{3}$ and luminiscent properties of these compounds, were studied. The new route (Combustion method) consist of the redox reactions between the respective metal nitrates and urea in a preheated furnace at ${500^{\circ}C}$. The Phosphor thus obtained were then heated at ${1000^{\circ}C}$ for 2-3 hours to get better luminiscent properties. The incorporation of $Eu^{3+}$ activator in these phosphors were checked by luminiscence investigations. Scanning electron microscopy (SEM) studies were carried out to understand surface morphological features and the particle size. X-ray energy dispersive analysis (EDAX) was also performed for the qualitative analysis of the phosphors.