• Journal of Navigation and Port Research
• /
• v.38 no.4
• /
• pp.335-341
• /
• 2014

Faced with global agenda of greenhouse abatement program including regulations and $CO_2$ emission trading scheme, shipping companies are enforced to a high level of efficiency in fuel consumption. Accordingly shipbuilding companies worldwide are required to develop fuel-efficient ships which otherwise traditionally consume a great amount of fossil fuels. In this dissertation, relevant to the improvement of fuel efficiency for commercial ships, design methodology through the numerical simulations are intensively described. This work consists of derivation of effective hydrodynamic design practice based on the application of longitudinal grooves to effectively improve the pressure distribution around ship hull. The primary objective of the present study is to improve ship resistance performance using longitudinal grooves which originate from long strips on the abdomen of humpback whale. Several groove shapes have been extensively investigated and the proposed shape efficiently controlled the variation of pressure distributions acting on the hull surface.

• Tribology and Lubricants
• /
• v.33 no.3
• /
• pp.85-91
• /
• 2017

This work studies the flow behaviors in the gap between the friction pad and separator in wet-clutch systems. The fluid volume of the lubricant is modeled using the entire system of wet-clutch pack of a dual clutch transmission that has larger outer radius of odd gear shifts and smaller inner radius of even gear shifts. Flow behaviors in the gap of the clutch pad are computed using the gear shift modes that consider the real relative velocities between the friction pad and separator. Flow behaviors in the gap of the disengaged clutch pad are mainly investigated for the wet-clutch system, whereas the engaged clutch pad is modeled with no fluid rate through the contacting surfaces. The developed hydrodynamic fluid pressures and velocity fields in the clutch pad gap are computed to obtain the relevant information for managing flow rates in wet-clutch packs under dual operating conditions during gear shifts. These hydrodynamic pressures and velocity fields are compared on the basis of each gear level and gap location, which is necessary to determine the effects of groove patterns on the friction pad. Shear stresses in the gap locations are also computed on the basis of the gear level for the inner and outer clutch pads. The computed results are compared and used for the design of cooling capacity against frictional heat generation in wet-clutch pack systems.

• Korean Journal of Optics and Photonics
• /
• v.19 no.2
• /
• pp.122-126
• /
• 2008

Dual backlight unit incorporating a single light source integrated with a beam splitting reflector was demonstrated, providing a surface light beam for both the keypad and the display section simultaneously. The reflector was realized by aligning a groove substrate with a matching cover, and a light guiding module comprising a stack of light guide panels and prism/diffuser sheets was attached to both sides of the reflector. A light emanating from the light source-placed in the middle of the substrate-undergoes a series of reflections through the reflector to reach the input of the light guiding module. Then it is transformed into a surface light beam, which is used to irradiate the keypad and display sections simultaneously. As for the accomplished dual surface light sources, the measured average luminance and the spatial luminance uniformity were respectively about $420\;cd/m^2$ and 69% for the keypad section, and $640\;cd/m^2$ and 79% for the display section.

• Journal of the Korean Institute of Gas
• /
• v.2 no.4
• /
• pp.42-46
• /
• 1998

Miniaturized specimen technology Permits mechanical behavior to be determined using a minimum volume of material. The technology is useful in case of not collecting a large amount of materials from industrial equipments. Five kinds of accelerated degradation materials were prepared by isothermal aging heat treatment at $630^{\circ}C$. Three kinds of specimens were prepared for impact testing. In order to increase plastic constraint of subsize specimen, side-groove was introduced. Results between subsize and full size impact testing were compared. Size effects correlations were developed for the impact properties of turbine rotor material. These correlations successfully predict the ductile brittle transition temperature (DBTT) of full size Charpy impact specimens based on subsize specimen data.

• Steel and Composite Structures
• /
• v.26 no.3
• /
• pp.329-345
• /
• 2018

This paper systematically investigated the mechanical performance of the weak-axis cover-plate connection, including a beam end monotonic loading test and a column top cyclic loading test, and a series of parametric studies for exterior and interior joints under cyclic loading using a nonlinear finite element analysis program ABAQUS, focusing on the influences of the shape of top cover-plate, the length and thickness of the cover-plate, the thickness of the skin plate, and the steel material grade. Results showed that the strains at both edges of the beam flange were greater than the middle's, thus it is necessary to take some technical methods to ensure the construction quality of the beam flange groove weld. The plastic rotation of the exterior joint can satisfy the requirement of FEMA-267 (1995) of 0.03 rad, while only one side connection of interior joint satisfied ANSI/AISC 341-10 under the column top cyclic loading. Changing the shape or the thickness or the length of the cover-plate did not significantly affect the mechanical behaviors of frame joints no matter in exterior joints or interior joints. The length and thickness of the cover-plate recommended by FEMA 267 (1995) is also suitable to the weak-axis cover-plate joint. The minimum skin plate thickness and a design procedure for the weak-axis cover-plate connections were proposed finally.

• International Journal of Korean Welding Society
• /
• v.1 no.1
• /
• pp.58-62
• /
• 2001

The surface of AC8A Ah alloy was modified by adding the Cu powder using a Plasma Transferred Arc (PTA) welding process. Under the optimum fabricating conditions, the modified surface of AC8A Ah alloy was observed to possess the sound microstructure with a minimum porosity. Hardness and wear resistance properties of the as-fabricated alloy were compared with those of the 76 heat-treated one. In case of the as-fabricated alloy, the hardness of the modified layer was twice that of the matrix region. Although significant increase in the hardness of the matrix region was observed after T6 heat treatment, the hardness of the modified layer was not observed to change. The wear resistance of the modified layer was significantly increased compared to that of the matrix region. The microstructure of a weld zone and the matrix region were investigated using the optical microscope, scanning electron microscope (SEM), electron probe microanalysis (EPMA), and transmission electron microscope (TEM). The primary and eutectic silicon in the weld zone were finer and more curved than in the matrix region, while some precipitates has had been found therein. According to the TEM observation, the predominant precipitate present in the weld zone was the $\theta$'phase, which is precipitated during cooling by rapid solidification in PTA welding process. Improvement of hardness and wear properties in the weld zone in the as-fabricated condition can be explained based on the presence of $\theta$’precipitates and fine primary and eutectic silicon distribution.

• Journal of Chest Surgery
• /
• v.50 no.1
• /
• pp.22-29
• /
• 2017

Background: The aim of this study was to analyze the preoperative attributes and clinical impacts of complete pericardiectomy in chronic constrictive pericarditis. Methods: A total of 26 patients were treated from January 2001 to December 2013. The pericardium was resected as widely as possible. When excessive bleeding or hemodynamic instability occurred intraoperatively, a cardiopulmonary bypass (CPB; n=3, 11.5%) or an apical suction device (n=8, 30.8%) was used. Patients were divided into 2 groups: those who underwent ${\geq}80%$ resection of the pericardium (group A, n=18) and those who underwent <80% resection of the pericardium (group B, n=8). Results: The frequency of CPB use was not significantly different between groups A and B (n=2, 11.1% vs. n=1, 12.5%; p=1.000). However, the apical suction device was more frequently applied in group A than group B (n=8, 30.8% vs. n=0, 0.0%; p=0.031). The postoperative New York Heart Association functional classification improved more in group A (p=0.030). Long-term follow-up echocardiography also showed a lower frequency of unresolved constriction in group A than in group B (n=1, 5.60% vs. n=5, 62.5%; p=0.008). Conclusion: Patients with chronic constrictive pericarditis demonstrated symptomatic improvement through complete pericardiectomy. Aggressive resection of the pericardium may correct constrictive physiology and an apical suction device can facilitate the approach to the posterolateral aspect of the left ventricle and atrioventricular groove area without the aid of CPB.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.55-55
• /
• 2009

FGB(Flexible Glasswool Backing) Submerged Arc Welding has been one of the main welding processes for one side butt welding in shipbuilding industries, which can efficiently improve the welding productivity by the addition of a supplementary filler metal into the molten weld pool. As recent ships have become larger in size, the application of high tensile and higher grade of steels has been continuously increased. Single pass FGB SA welding process accompanies such a high heat input when welding thick plates that the mechanical properties of weld metal can be dramatically degraded. This study has been performed in order to obtain high toughness and tensile properties of high heat input FGB SA welds, and to evaluate the effect of alloy elements on their mechanical properties. To complete welding 25mm-thick EH36 grade steel plate by single pass, 1.2mm diameter and 1.0mm long cut wires has been distributed in the groove before welding, and three different test coupons have been made using C-1.5%Mn, C-1.8%Mn-0.5%Mo, and C-1.4%Mn-1.7%Ni cut wires to investigate the influence of nickel(Ni) and molybdenum(Mo) on the mechanical properties of welds. Test results showed that the addition of Ni and Mo effectively promotes the formation of Acicular Ferrite(AF), while significantly reducing the amount of Grain Boundary Ferrite(GBF) in weld metal microstructures, which resulted in a beneficial effect on low temperature impact toughness and strength.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.3
• /
• pp.313-318
• /
• 2013

Magnetic abrasive polishing is an advanced deburring process for nonmagnetic materials and micropattern products that have non-machinability characteristics. Despite these advantages, there are some problems with using MAP for deburring. MAP has introduced geometric errors into microgrooves because of an over-cutting force caused by uncontrolled magnetic abrasives in the MAP tool. Thus, in this study, to solve this problem, an EP (electrolyte polishing)-MAP hybrid polishing process was developed for deburring microgrooves in an STS316 material. In addition, an evaluation of EP-MAP for the deburring of microgrooves was carried out by profiling the burrs. The results of the experiment showed geometric errors after the deburring process using MAP. However, in the case of EP-MAP, no geometric error was observed after the process because of the lower material removal rate in EP-MAP.

• Tribology and Lubricants
• /
• v.34 no.1
• /
• pp.33-41
• /
• 2018

This paper describes a new test rig for identification of rotordynamic force coefficients of squeeze film dampers (SFDs) in automotive turbochargers (TCs). Prior studies have mainly concentrated on relatively large-sized SFDs used in aircraft engines, turbocompressors, and turbopumps. The main objective of the current study is to propose a test rig for identification of dynamic force coefficients of small-sized SFDs (a journal diameter of ~11 mm). The current test rig consists of a journal, a SFD cartridge, four support rods, an upper structure, a data acquisition (DAQ) system, and an oil circulation unit. The annular gaps between the journal outer surface and SFD cartridge inner surface create SFD film lands. The damper has two parallel film lands separated by a central groove, having an axial length and depth of 3 mm. Each film land has a length of 4 mm with a $40{\mu}m$ radial clearance. The static load and dynamic impact tests identify the structural characteristics (i.e., stiffness and natural frequency) of the journal and assembled test rig. The measurements show good agreement with predictions. The SFD performance data from this test rig will be used to develop innovative TC rotor systems with improved NVH and reliability characteristics incorporating advanced SFD technology.