부유 게이트 Floating gate (FG) 플래시 메모리 소자의 단점을 개선하기 위해 전하 포획 층에 전하를 저장하는 전하 포획 플래시 메모리 Charge trap flash (CTF)소자에 대한 연구가 활발히 진행되고 있다. CTF소자는 FG플래시 메모리 소자에 비해 비례축소가 용이하고 긴 retention time을 가지며, 낮은 구동 전압을 사용하는 장점을 가지고 있다. CTF 소자에서 비례축소에 따라 단채널 효과와 펀치-쓰루 현상이 증가하는 문제점이 있다.본 연구에서는 CTF 단채널 효과와 펀치-쓰루 현상을 감소시키기 위한 방법으로 silicon-on-insulator (SOI) 기판을 사용하였으며 SOI기판에서 절연층의 깊이에 따른 전기적 특성을 고찰하였다. silicon-oxide-nitride-oxide-silicon(SONOS) 구조를 가진 CTF 메모리 소자를 사용하여 절연층의 깊이 변화에 따른 subthreshold swing특성, 쓰기-지우기 동작 특성을 TCAD 시뮬레이션 툴인 Sentaurus를 사용하여 조사하였다. 소스와 드레인의 junction depth는 20 nm 사용하였고, 절연층의 깊이는 5 nm~25 nm까지 변화하면서 절연층의 깊이가 20 nm이하인 fully depletion 소자에 비해, 절연층의 깊이가 25 nm인 소자는 partially depletion으로 인해서 드레인 전류 레벨이 낮아지고 subthreshold swing값이 증가하는 현상이 나타났다. 절연층의 깊이가 너무 얕을 경우, 채널 형성의 어려움으로 인해 subthreshold swing과 드레인 전류 레벨의 전기적성질이 SOI기판을 사용하지 않았을 경우보다 떨어지는 경향을 보였다. 절연층의 깊이가 17.5 nm인 경우, CTF소자의 subthreshold swing과 드레인 전류 레벨이 가장 좋은 특성을 보였다.
Purpose: This study classified alveolar arch forms and evaluated differences in alveolar bone thickness among arch forms in the anterior esthetic region using cone-beam computed tomography (CBCT) images. Materials and Methods: Axial views of 113 CBCT images were assessed at the level of 3 mm below the cementoenamel junction (CEJ) of the right and left canines. The root center points of teeth in the anterior esthetic region were used as reference points. Arch forms were classified according to their transverse dimensions and the intercanine width-to-depth ratio. The buccolingual alveolar bone thickness of each tooth was measured at 3 mm below the CEJ and at the mid-root level. Differences in the mean thicknesses among arch forms were analyzed. Results: Anterior maxillary arches could be classified as long narrow, short medium, long medium, and long wide arches. Significant differences in buccolingual alveolar bone thickness among the arch groups were found at both levels. The long wide arches presented the greatest bone thickness, followed by the long medium arches, while the long narrow and short medium arches were the thinnest. Conclusion: Arch forms were classified as long narrow, short medium, long medium, and long wide. The buccolingual alveolar bone thickness exhibited significant differences among the arch forms.
Recent discoveries of ferroelectric properties in ultrathin doped hafnium oxide (HfO2) have led to the expectation that HfO2 could overcome the shortcomings of perovskite materials and be applied to electron devices such as Fe-Random access memory (RAM), ferroelectric tunnel junction (FTJ) and negative capacitance field effect transistor (NC-FET) device. As research on hafnium oxide ferroelectrics accelerates, several models to analyze the polarization switching characteristics of hafnium oxide ferroelectrics have been proposed from the domain or energy point of view. However, there is still a lack of in-depth consideration of models that can fully express the polarization switching properties of ferroelectrics. In this paper, a Zr-doped HfO2 thin film based metal-ferroelectric-metal (MFM) capacitor was implemented and the polarization switching dynamics, along with the ferroelectric characteristics, of the device were analyzed. In addition, a study was conducted to propose an applicable model of HfO2-based MFM capacitors by applying various ferroelectric switching characteristics models.
This paper deals with a novel structure of poly-Si solar cell. A grain boundary(GB) of poly-Si acts as potential barrier and recombination center for photo-generated carriers. To reduce unwanted side effects at the GB of poly-Si, we employed physical GB removal of poly-Si using chemical solutions. Various chemical etchants such as Sirtl, Yang, Secco, and Schimmel were investigated for the preferential GB etching. Etch depth about 10 ${\mu}m$ was achieved by a Schimmel etchant. After a chemical etching of poly-Si, we used $POCl_3$ for emitter junction formation. This paper used an easy method of top electrode formation using a RF sputter grown ITO film. ITO films with thickness of 300 nm showed resistivity of $1.26{\times}10^{-4}{\Omega}-cm$ and overall transmittance above 80%. Using a preferential GB etching and ITO top electrode, we developed a new fabrication procedure of poly-Si solar cells. Employing optimized process conditions, we were able to achieve conversion efficiency as high as 16.6% at an input power of 20 $mW/cm^2$. This paper investigates the effects of process parameters: etching conditions, ITO deposition factors, and emitter doping densities in a poly-Si cell fabrication procedure.
Purpose: To evaluate the performance of the LOGICON Caries Detector using RVG-4 and RVG-ui sensors, by comparing results of each detector to the results of clinical and histological examinations. Materials and Methods : Pairs of extracted teeth were radiographed, and a total of 57 proximal surfaces, which included both carious and non-carious situations, were analyzed. The RVG-4 produced 8-bit images, while the RVG-ui unit produced 12-bit images, which were taken in the high sensitivity mode. The images produced by the LOGICON were evaluated by a trained observer using both automated and manual caries detection software modes. Ground sections of the teeth established the actual absence or existence of caries. Results: LOGIC ON-aided caries detection and depth discrimination of the RVG-4 and RVG-ui sensors were equally inconsistent irrespective of whether the LOGIC ON software was set to the automated or manual mode. Sensitivity ranged from 50% to 57% for caries penetration of the enamel-dentin junction. Conclusion: Care needs to be taken when using LOGIC ON in conjunction with RVG images as an adjunct for treatment planning dental caries. Even when applied by a trained observer, substantial discrepancies exist between the results of the LOGIC ON software-guided evalutations using RVG images and histologic examination.
The crude oil pump system is the equipment for transporting crude oil and it consists of 3 major components, a motor and an impeller which discharge underground crude oil, a pipestack that transmits the cooling oil and power, and a cooling oil unit & junction box that provides cooling oil and electric power. When considering the system characteristics that it has to be installed at a depth of deeper than 100 m, a design technology for the efficient control of the heat occurring at a conductor and motor is necessary and it is the essential factor for ensuring system durability. In this paper, therefore, cooling oil flow has been calculated to satisfy the limit value of the system temperature by analyzing heat flow considering the related losses such as loss of conductor, contact resistor loss at the conductor connection, and operation loss of motor. And the operation temperature has been set up based on the temperature of crude oil and the heat of motor and conductor. Also, a design for cooling of crude oil pump system has been proposed by calculating the operation pressure loss and selecting the capacity of a cooling oil pump and a heat exchanger.
This paper presents a proper condition to achieve above 19 % conversion efficiency using PC1D simulator. Cast poly-Si wafers with resistivity of 1 $\Omega$-cm and thickness of 250 ${\mu}{\textrm}{m}$ were used as a starting material. Various efficiency influencing parameters such as rear surface recombination velocity and minority carrier diffusion length in the base region, front surface recombination velocity, junction depth and doping concentration in the Emitter layer, BSF thickness and doping concentration were investigated. Optimized cell parameters were given as rear surface recombination of 1000 cm/s, minority carrier diffusion length in the base region 200 ${\mu}{\textrm}{m}$, front surface recombination velocity 100 cnt/s, sheet resistivity of emitter layer 100 $\Omega$/$\square$, BSF thickness 5 ${\mu}{\textrm}{m}$, doping concentration 5$\times$10$^{19}$ cm$^3$ . Among the investigated variables, we learn that a diffusion length of base layer acts as a key factor to achieve conversion efficiency higher than 19 %. Further details of simulation parameters and their effects to cell characteristics are discussed in this paper.
터빈 익렬 내에서 발생하는 2차유동은 터빈 익렬에서 전체 공기역학적 손실의 30$\sim$50%, 입구 스테이터에서는 약 20%를 차지하며 터빈 효율 향상에 있어 개선해야 될 중요한 부분으로 인식되고 있다. 본 논문에서는 블레이드 앞전에 모서리 홈을 만들어 홈의 높이 및 깊이 등의 형상 변수를 변화시켜가면서 말굽와류의 발생 영역 및 강도의 감쇄 특성 및 구조에 대해 상용코드인 $FLUENT^{TM}$를 이용하여 수치해석적인 방법으로 연구하였다.
목 적 : 두경부 종양의 방사선치료에서 동일 방사선 조사면을 분리하여 X-선과 전자선을 인접시켜 조사하는 경우는 빈번히 사용되는 방법이다. 따라서 본 연구는 X-선과 전자선 조사면의 인접면에서의 선량을 측정하여 임상에 적용할 수 있는 자료를 얻고자 하였다. 대상 및 방법 : 본 연구는 Clinac1800 (Varian, USA) 선형가속기에서 방출되는 6MV X-선과 9 MeV 전자선을 이용하였다. 흡수선량을 측정하기 위해 X-OMAT V film을 사용하였다. 조사야 $10cm{\times}10cm$에 0.1Gy - 4Gy를 조사하여 film densitometer (WP102 : Welhofer, German)로 OD 값(광학 밀도)를 얻어 film의 특성 곡선을 얻었다. X-선과 전자선 조사면을 분리하여 인접 조사할 때 X-선 조사면은 $10cm{\times}10cm$의 X축 중심에서 2 cm부터 폭 3cm의 차폐를 하고 X-선 조사면에서 차폐된 부분을 전자선 조사면으로 하였다. 전자선 조사면은 $15cm{\times}15cm$ cone을 이용하였다. 흡수선량 측정은 solid water phantom에서 깊이 0 cm(표면), 0.5 cm, 1.5 cm, 2cm, 3 cm에서 film을 설치하고 X-선은 8 cm 깊이에 100 cGy를 조사하고 전자선은 SSD(source surface distance) 100cm로 표면에서 X-선 조사면에 일치시키고 1Gy를 조사하였다. 선량 측정은 X-선과 전자선 조사면의 인접면에서 film densitometer로 scan하여 OD 값을 구하고 6 MV X-선의 Dmax의 OD값을 기준으로 비교하였다. 기준 흡수선량을 구하기 위해 X-선과 전자선 각각의 흡수선량을 깊이 0 cm(표면), 0.5cm, 1.5cm, 2cm, 3cm에서 측정하였다. 결 과 : X-선과 전자선의 조사면을 인접시켰을 때 깊이 0 cm, 0.5 cm, 1.5 cm, 2 cm, 3 cm에서의 두 조사면의 인접면에서의 선량 분포의 분석에서 X-선 조사면에서 선량 증가는 깊이 1.5 cm에서 폭 7 mm에 걸쳐 있었고 최고 $6\%$의 증가를 보였으며 다른 측정 깊이에서는 선량증가가 허용범위 내에 있었다. 그리고 전자선 조사면쪽에서 선량 감소는 전 측정 깊이 0.5 cm-3 cm에서 각각 폭이 1mm-12.5 mm에 걸쳐 $4.5\%-30\%$의 주변부보다 선량감소를 보였다. 결 론 : 본 연구에서 X-선과 전자선을 표면에서 인접시켜 조사 할 때 두 조사면의 인접면을 중심으로 X-선 조사면 쪽에서 선량증가, 전자선 조사면쪽에서 선량 감소가 있음을 확인하였다. 위의 연구 결과는 X-선과 전자선의 인접 방사선조사를 할 때 유용한 참고 자료가 될 수 있겠다.
Purpose: To determine the clinical value of the Siewert classification for gastic-cancer patients in Korea, we evaluated and compared the clinicopathologic factors of type II and type III cancer. Materials and Methods: The medical records of 89 consecutive patients who had undergone surgery for an adenocarcinoma of the gastroesophageal junction (GEJ) at the Department of Surgery, Hanyang University Hospital, between Jun. 1992 and Dec. 2003 were reviewed retrospectively. Results: There were one patient with type I, 12 pateints with type II and 77 patients with type III. During the same period, 1,341 patients underwent surgery for a gastric carcinoma, so proportion of GEJ cancer being $6.6\%$. The median followup duration was 31 months (range: $2\∼135$ months), and the follow-up rate was $100\%$. Between type II and type III cancers, there were no significant differences in the clinicopathologic variables including age, sex, gross appearance, histologic type, depth of invasion, and pathologic stage. The longest diameter of the tumor was larger in type III ($6.1\pm2.1$ cm) than in type II ($3.9\pm1.1$ cm)(P=0.001). A total gastrectomy with Roux-en-Y esophagojejunostomy was done most frequently, while jejunal interposition was done in 3 cases of type II and 2 cases of type III. More than a D2 lymphadenectomy was done all cases. The numbers of dissected lymph nodes and metastatic lymph nodes in type II were 43.8 and 5.8 respectively, while they were 49.8 and 8.1 in type III, but the difference between the two groups were not statistically significant. The mean length of the proximal resection margin was $15\pm5$ mm in type II and $21\pm13$ mm in type III, but this difference was not statistically significanct. The time to recurrence after operation was 19.3 months in type II and 16.9 months in type III. The five-year survival rates of type II and III were $68.8\%\;and\;52.7\%$ respectively, but difference was not significant. Conclusion: There were no significant differences in the clinicopathologic variables, including survival rate, between type II and type III cancers in Korean patients According to these findings, it appears to be reasonable to classify type III cancer as a cardia cancer in a broad sense.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.