• Journal of Welding and Joining
• /
• v.16 no.6
• /
• pp.35-43
• /
• 1998

In this paper, the fracture toughness evaluation of the various microstructures such as HAZ, F.L and W.M in weldment of TMCP steel which has the softening zone owing to high heat input welding was carried out by using of the small punch(SP) test. In addition, the fracture toughness with the specimen orientation of rolled TMCP steel was investigated by means of SP test and the crack opening displacement (COD) test and then was compared with that of conventional SM50YB steel. From the results of SP test for TMCP steel, it could be seen that the SP energy transition curves of three different orientation were shifted to higher temperature side in order of S, T and L. But the {TEX}$DBTT_{SP}${/TEX} of each orientation specimen did not show a lot of differences and were quite lower than those of conventional SM50YB steel. The mechanical properties of HAZ structure in weldment of TMCP steel such as hardness, SP energy at room temperature and -196$^{\circ}C$ and the upper shelf energy of SP energy transition curve were lower than those of base metal due to softening. The {TEX}$DBTT_{SP}${/TEX} of each microstructure in weldment of TMCP steel increased in order of HAZ, F.L and W.M against base metal, but all microstructures showed a quite lower {TEX}$DBTT_{SP}${/TEX} than those of SM50YB steel.

• Journal of the Korean Institute of Rural Architecture
• /
• v.20 no.1
• /
• pp.11-18
• /
• 2018

The study aims to address the energy crisis and realize self-sufficiency of building as part of local energy independence, breaking away from a single concentrated energy supply system. It is intended to develop modules of the outside insulation composite panels that conform to passive certification criteria and for site-assembly systematization. The method of study first identifies trends and passive house in literature and advanced research. Second, the target performance for development is set, and the structural material is selected and designed to simulate performance. Third, a test specimen of the passive outside insulation curtain wall module designed is manufactured and constructed to test its heat transmission coefficient, condensation performance and airtightness. Finally, analyze performance test results, and explore and propose ways to improve the estimation and improvement of incomplete causes to achieve the goal. The final test results achieved the target performance of condensation and airtightness, and the heat transmission coefficient was $0.16W/(m^2{\cdot}K)$, which is $0.01W/(m^2{\cdot})K$ below the performance target. As for the lack of performance, we saw a need for a complementary design to account for simulation errors. It also provided an opportunity to recognize that insulated walls with performance can impact performance at small break. Thus, to be commercialized into a product with the need for improvement in the design of the joint parts, a management system is needed to increase the precision in the fabrication process.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.4B
• /
• pp.207-214
• /
• 2008

Under future internet environment, wireless sensor networks will be used in a wide range of applications. A major problem for designing sensor protocol is developing the most energy efficient technique to monitor an area of interest for a long time since sensors have some constraints such as small and a limited energy level. In addition, data latency is often a critical issue since sensory data is transmitted via multi hop fashion and need to be delivered timely for taking an appropriate action. Our motivation for designing a data forwarding protocol is to minimize energy consumption while keeping data latency bound in wireless sensor networks. In this paper, we propose a data forwarding protocol that consists of wakeup scheduling and MAC protocols, the latter of which is designed to achieve load balancing. Simulation results show that the proposed framework provides more energy-efficient delivery than other protocol.

• Journal of Radiation Protection and Research
• /
• v.23 no.2
• /
• pp.103-107
• /
• 1998

The influence of calm conditions on the atmospheric dispersion analyses at KAERI site, which is located at a complex inland basin, was investigated. The U. S. NRC's computer programs XOQDOQ and PAVAN were used to estimate dispersion factors for routine and postulated accidental releases from nuclear facilities, respectively. The joint frequency distribution was obtained from the annual meteorological data measured in 1997 and used as input data of the computer programs. When the definition of calm is changed from 0.5 m $sec^{-1}$ to 0.21 m $sec^{-1}$, the maximum sector dispersion factor becomes 1.62 and 2.16 times higher for routine and postulated accidental releases, respectively.

• Journal of Power System Engineering
• /
• v.18 no.5
• /
• pp.122-128
• /
• 2014

Generally, the mechanical components and structures are joined by many welding techniques, and therefore the welded joints are inevitable in the construction of structures. The Alloy 617 was initially developed for high temperature applications above $800^{\circ}C$. It is often considered for use in aircraft and gas turbines, chemical manufacturing components, and power generation structures. Especially, the Alloy 617 is the primary candidate for construction of intermediate heat exchanger (IHX) on a very high temperature reactor (VHTR) system. In the present paper, the low cycle fatigue (LCF) life of Alloy 617 base metal (BM) and the gas tungsten arc welded (GTAWed) weld joints (WJ) are evaluated by using the previous experimental results under strain controlled LCF tests. The LCF tests have been performed at room temperature with total strain ranges of 0.6, 0.9, 1.2 and 1.5%. The LCF lives for the BM and WJ have been evaluated from the Coffin-Manson and strain energy based life methods. For both the BM and WJ, the LCF lives predicted by both Coffin-Manson and strain energy based life methods was found to well coincide with the experimental data.

• Current Photovoltaic Research
• /
• v.8 no.4
• /
• pp.124-128
• /
• 2020

Output power of photovoltaic (PV) modules installed outdoors decreases every year due to environmental conditions such as temperature, humidity, and ultraviolet irradiations. In order to promote the installation of PV modules, the reliability must be guaranteed. One of the important factors affecting reliability is intermetallic compounds (IMC) layer formed in ribbon solder joint. For this reason, various studies on soldering properties between the ribbon and cell have been performed to solve the reliability deterioration caused by excessive growth of the IMC layer. However, the IMC layer of the PV module interconnected by multi-wires has been studied less than using the ribbon. It is necessary to study soldering characteristics of the multi-wire module for improvement of its reliability. In this study, we analyzed the growth of IMC layer of the PV module with multi-wire and the degradation of output power through damp-heat test. The fabricated modules were exposed to damp-heat conditions (85 ºC and 85 % relative humidity) for 1000 hours and the output powers of the modules before and after the damp-heat test were measured. Then, the process of dissolving ethylene vinyl acetate (EVA) as an encapsulant of the modules was performed to observe the IMC layer. The growth of IMC layer was evaluated using OM and FE-SEM for cross-sectional analysis and EDS for elemental mapping. Based on these results, we investigated the correlation between the IMC layer and output power of modules.

• Journal of Energy Engineering
• /
• v.24 no.4
• /
• pp.183-191
• /
• 2015

Studies on the environment-friendly and permanent low energy saving measure are and will continue to be an eternal challenge. However, the demand is high for the technologies that can save energy significantly in everyday life that produce tangible benefits for the users by applying saving factors and that anyone can access easily when it comes the related procedure. Government policies related to the improvement of energy effect in the existing building structure are characterized by complex procedure. Moreover, cost required and reliability issue emerge when request is made to an expert. Accordingly, this study seeks to present energy improvement plan that can be utilized simply and conveniently at any place, any time by enabling customized design according to individual taste by enabling energy change amount and grade prediction when the users select only the part that they want to replace by using a simple program.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.9
• /
• pp.136-143
• /
• 2013

In this paper, a algorithm to find joints of a small animal like a lizard from the multiple-view silhouette images is presented. The proposed algorithm is able to calculate the 3D coordinates so that the locomotion of the lizard is markerlessly reconstructed. The silhouette images of the lizard was obtained by a adaptive threshold algorithm. The skeleton image of the silhouette image was obtained by Zhang-Suen method. The back-bone line, head and tail point were detected with the A* search algorithm and the elimination of the ortho-diagonal connection algorithm. Shoulder joints and hip joints of a lizard were found by $3{\times}3$ masking of the thicked back-bone line. Foot points were obtained by morphology calculation. Finally elbow and knee joint were calculated by the ortho distance from the lines of foot points and shoulder/hip joint. The performance of the suggested algorithm was evaluated through the experiment of detecting joints of a small lizard.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.11 no.3 s.55
• /
• pp.23-31
• /
• 2007

Fast bridge construction has been increasingly needed according to the changed construction environment. This paper deals with quasi-static tests on precast piers for bridge substructures. One of the most crucial aspect of the design of precast prestressed concrete bridge piers is the seismic performance. Seven precast pier elements were fabricated. The amount of prestressing bars, the prestressing force, and the location and number of the joint between segments were the main test parameters. Test results showed that the introduced axial prestress made the restoration of the deformation under small lateral displacement and minor damage. However, there was no effect of the prestress when the plastic hinge region was damaged severely due to large lateral displacement. Judging from the observed damage, the design of the joints in precast piers should be done for the first joint between the foundation and the pier segment. The amount of the necessary prestressing steel may be designed to satisfy the P-M diagram according to the service loads, not by having the same steel ratio as normal RC bridge piers. In order to satisfy the current required displacement ductility, it is necessary to have the same amount of the transverse reinforcements as RC piers. As the steel ratio increases, the energy absorption capacity increases. The number of joints showed a little influence on the energy absorption capacity.

• Journal of International Area Studies (JIAS)
• /
• v.13 no.1
• /
• pp.107-133
• /
• 2009

International relations in the 21st century is featured by boundless competition among nations to secure sufficient energy resources for achieving economic development. Resource diplomacy, therefore, is competitive in its nature, which is derived from the fact that resources of the globe are limited. Chinese recent economic growth has been possible mainly due to its success in resource diplomacy. The Chinese resource diplomacy has shown two different patterns according to target regions. On the one hand, China has pursued multilateral approach to Central Asia region, by which China aimed to secure energy with joint exploration method in the region. Chinese resource diplomacy toward Africa, on the other hand, has been based on bilateral approach combined with unit-centered economic aid to African nations. This difference in Chinese foreign policy pattern seems to be derived from three factors: namely, Chinese strategic considerations on geopolitical condition, regional security sensitivity, and legacies of Chinese long-time non-alignment diplomacy since the 1950s. Whether China is able to maintain the current pattern of resource diplomacy will be depended on how wisely China pursue its relations with two other global powers: Russia in the Central Asia and the U.S. in Africa. In this regard, the Chinese resource diplomacy is expected to work as determining factor of shaping a pattern of tri-lateral strategic relations among the U.S., Russia, and China. Chinese resource diplomacy thus will determine the future direction of the global politics in terms of strategic arrangement.