• Tunnel and Underground Space
• /
• v.26 no.4
• /
• pp.283-292
• /
• 2016

A computer program code was developed to estimate hydraulic behavior of the 2-D connected pipe network system, and implemented to evaluate the effect of joint aperture on hydraulic parameters of fractured rock masses through numerical experiments. A total of 216 stochastic 2-D DFN(discrete fracture network) blocks of $20m{\times}20m$ were prepared using two joint sets with fixed input parameters of joint orientation, frequency and size distribution. Two different cases of joint aperture variation are considered in this study. The hydraulic parameters were estimated for generated 2-D DFN blocks. The hydraulic anisotropy and the chance for equivalent continuum behavior of the DFN system were found to depend on the variability of joint aperture.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.6
• /
• pp.61-68
• /
• 2007

The hole for the insertion of the pin in the shank is exist at ball joint connection of the space frame. It brings about the brittle fracture caused by stress concentration. Consequently it cannot expect the deformation performance or energy absorption performance from ball joint connection. In this study we developed a new connection details which will increase the plastic deformation performance at ball joint connection and can absorb the error in construction, which expect the plastic deformation performance at the reduced shank without brittle fracture at the screw of bolt and pin. Also it's capacity is verified by the performance in numerical analysis and test. We confirmed bolt's plastic deformantion performance through controled shank and pin's area.

• Steel and Composite Structures
• /
• v.3 no.5
• /
• pp.321-331
• /
• 2003

The paper presents the results of an experimental investigation conducted on welded tubular joints, that are employed in offshore platforms, to study the behaviour and strength of these joints under axial brace compression loading. The geometrical configuration of the joints tested were T and Y. The nominal diameter of the chord and brace members of the joint were 324 and 219 mm respectively. The chord thickness was 12 mm and the brace 8 mm. The tested joints are approximately quarter size when compared to the largest joints in the platforms built in a shallow water depth of 80 m in the Bombay High field. Some of the joints were actually fabricated by a leading offshore agency which firm is directly involved in the fabrication of prototype structures. Strength of the internally ring-stiffened joints was found to be almost twice that of the unstiffened joints of the same configuration and dimensions. Bending of the chord as a whole was observed to be the predominant mode of deformation of the internally ring-stiffened joints in contrast to ovaling and punching shear of the unstiffened joints. It was observed in this investigation that unstiffened joint was stiffer in ovaling mode than in bending and that midspan deflection of unstiffened joint was insignificant when compared to that of the internally ring stiffened joint. The measured midspan deflection of the unstiffened joint in this investigation and its relation with the applied axial load compares very well with that predicted for the brace axial displacement by energy method published in the literature. A comparison of the measured deflection and ovaling of the unstiffened joint was made with that published by the author elsewhere in which numerical prediction of both quantities have been made using ANSYS software package. The agreement was found to be quite good.

• Journal of the Korean Geotechnical Society
• /
• v.33 no.4
• /
• pp.5-15
• /
• 2017

Three-hinge failure occurs in a jointed rock slope with a joint set parallel with slope and a conjugate joint set. Limit Equilibrium Method (LEM) and Finite Element Method (FEM) which are commonly used for slope design, are not suitable for evaluating stability against three-hinge failure, and this study performed parametric study to analyze the failure mechanism and to find influence factors causing three-hinge failure using UDEC which is a commercial two-dimensional DEM based numerical program. Numerical analyses were performed for various joint structural conditions and joint properties as well as ground water conditions. It was found that pore water pressure is the main factor triggering the three-hinge failure and the mode of failure depends on friction angle of basal joint and bedding joint set. The results obtained from this study can be used for adequate and economic footwall slope reinforcement design and construction.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.28 no.3
• /
• pp.129-139
• /
• 2024

In this study, the SBC system, a new mechanical joint method, was developed to improve the constructability of precast concrete (PC) beam-column connections. The reliability of the finite element analysis model was verified through the comparison of experimental results and FEM analysis results. Recently, the intermediate moment frame, a seismic force resistance system, has served as a ramen structure that resists seismic force through beams and columns and has few load-bearing walls, so it is increasingly being applied to PC warehouses and PC factories with high loads and long spans. However, looking at the existing PC beam-column anchorage details, the wire, strand, and lower main bar are overlapped with the anchorage rebar at the end, so they do not satisfy the joint and anchorage requirements for reinforcing bars (KDS 41 17 00 9.3). Therefore, a mechanical joint method (SBC) was developed to meet the relevant standards and improve constructability. Tensile and bending experiments were conducted to examine structural performance, and a finite element analysis model was created. The load-displacement curve and failure pattern confirmed that both the experimental and analysis results were similar, and it was verified that a reliable finite element analysis model was built. In addition, bending tests showed that the larger the thickness of the bolt joint surface of the SBC, the better its structural performance. It was also determined that the system could improve energy dissipation ability and ductility through buckling and yielding occurring in the SBC.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.369-374
• /
• 2018

In this paper, the energy cost saving in multi-channel electric vehicle charging system. Joint use of the electric car charger battery state of charging proposed a method based charging. A linear programming with two type is used for optimal control, and the time-of-use price is included to calculate the energy costs. Simulation results show that the reductions of energy cost and peak power can be obtained using proposed method.

• Nuclear Engineering and Technology
• /
• v.53 no.2
• /
• pp.562-571
• /
• 2021

In this work, we propose a new mechanistic model for the treatment of helium behaviour which includes the description of helium solubility in oxide fuel. The proposed model has been implemented in SCIANTIX and validated against annealing helium release experiments performed on small doped fuel samples. The overall agreement of the new model with the experimental data is satisfactory, and given the mechanistic formulation of the proposed model, it can be continuously and easily improved by directly including additional phenomena as related experimental data become available.

• 대한방사선방어학회:학술대회논문집
• /
• 2010.04a
• /
• pp.94-95
• /
• 2010

The accuracy of typical dosimeters used around high energy accelerator were proved by dose rate measurements. The experimental neutron spectrum were useful for improving high energy Monte Carlo codes by validating the implemented models. In series of this joint research the experimental data will be upgrade successively. This research program is opened to experts and students in Korea, too.

• Journal of Radiation Protection and Research
• /
• v.37 no.3
• /
• pp.116-122
• /
• 2012

A short-term atmospheric dispersion factor (${\chi}/Q$) is an essential element for radiological dose assessment following a hypothetical accidental releases of light-water nuclear power plants. The U. S. NRC developed PAVAN program to comply with the U. S. NRC's Regulatory Guide 1.145. Meteorological data is an essential element for atmospheric dispersion, and PAVAN uses a joint frequency distribution data, which represents the occurrence probability of wind speed and wind direction for atmospheric stability. Using the meteorological data measured at Kori and Wolsung sites for the last 5 years (from 2006 to 2010), a variety of joint frequency distribution data were prepared to evaluate ${\chi}/Q$ values with different wind speed classifications (U. S. NRC's recommendation and even distribution of occurrence probability) and periods of meteorological data to be analyzed (1 year, 2 year, 3 year, 4 year, 5 year). As a result, it was found that the influence of the wind speed classification on ${\chi}/Q$ values is little, while the influence of the periods of meteorological data to be analyzed is relatively significant, representing more than 1.5 times in the ratio of maximum to minimum values.

• Tunnel and Underground Space
• /
• v.33 no.6
• /
• pp.574-593
• /
• 2023

In this study, the effectiveness and applicability of a newly designed Compact CNS shear box for conducting direct shear tests on jointed rock specimens were investigated. CNS joint shear tests were conducted on jointed rocks with Artificially generated roughness while varying the fracture surface roughness coefficient and initial normal stress conditions. In addition, displacement data were validated by Digital image correlation analysis, fracture patterns were observed, and comparative analysis was conducted with previously studied shear behavior prediction models. Furthermore, the accuracy of the displacement data was confirmed through DIC analysis, the fracture patterns were observed, and the shear properties obtained from the tests were compared with existing models that predict shear behavior. The findings exhibited a strong correlation with specific established empirical models for predicting shear behavior. Furthermore, the potential linkage between the characteristics of shear behavior and fracture patterns was deliberated. In conclusion, the CNS shear box was shown to be applicable and effective in providing data on the shear characteristics of the joint.