• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.8
• /
• pp.1727-1734
• /
• 2011

In this paper, a position control scheme of the ink droplet is presented for the high image quality and print speed ink jet printer. The proposed scheme estimates the impact position and compensates it by control of the jet strobe time based on the dynamic equations describing the moving trajectory of the ejected ink droplet. Compared to the conventional jet strobe control which is based on the simple synchronization with the position signal of the ink jet nozzle, the proposed control scheme provides more accurate impact position control while the carrier is moving with accelerated or decelerated speed as well as steady state speed with fluctuations. The availability of printing during the acceleration and deceleration states of the carrier moving enables the print speed up and the frame size down which means the cost down.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.12
• /
• pp.1173-1180
• /
• 2013

High Resolution Range Profile-Jet Engine Modulation imagery first introduced in 2005 carries out radar target recognition by localizing the position of the jet engine installed on the aircraft target. This paper presents a new approach for estimating the jet engine position in the HRRP-JEM image based on the eccentricity of a complex signal. It can effectively evaluate the contribution of the JEM component to the radar received signal in a range bin of the HRRP-JEM image. Therefore, the localization is expected to be performed more quantitatively and reliably by pinpointing the range bin corresponding to the jet engine position where the JEM contribution is maximized. The simulation results of realistic aircraft models validated the effectiveness of the proposed concept.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2765-2770
• /
• 2008

The purpose of tunnel ventilation system for long road tunnels is to keep certain levels of Visibility Index and the concentration of CO. Additional equipments such as jet fans are used in road tunnel to discharge pollutants in the road tunnel. The control algorism of tunnel ventilation system takes the value of sensors as input, and then gives the operation method of jet fans in tunnel as output. Information on the variation of CO concentration in tunnel when jet fans are running is needed to minimize their operation time. Numerical analysis is used in this paper because of the difficulty of conducting experiments under standard condition for ventilation of road tunnel. The concentration of CO has been calculated by using 3-dimensional CFD under transient condition with speed of cars, quantity of air ventilation, and the results for various operation position of jet fans are compared.

• Journal of Advanced Marine Engineering and Technology
• /
• v.22 no.1
• /
• pp.52-66
• /
• 1998

An experimental study on the flow characteristics was performed for a two-dimensional turbulent wall attaching offset jet at different oblique angles to a surface. The flow characteristics were investigated by using a split film probe with the modified Stock's calibration method. The jet mean velocity, turbulent intensity, wall static pressure coefficient profiles, and time-averaged reattachment point were measured at the Reynolds number Re (based on the nozzle width, D) ranging from 17700 to 53200, the offset ratio H/D from 2.5 to 10, and the inclined angle .alpha. from 0.deg. C to 40.deg. C. The Correlations between the maximum pressure position, minimum pressure position, and reattachment point and offset ratios, and inclined angles are presented.

• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.4
• /
• pp.317-324
• /
• 2004

The ink jet printer media advance system is required to be exactly driven to the target position via tracking the reference velocity profile to obtain the high quality print image. A single gain PID controller is not sufficient to fulfill the control objectives, the exact velocity tracking and the accurate positioning, at the same time. A dual PID controller and its switching strategy are presented in this paper to achieve the control objectives. The media advance system is controlled by two separate PID controllers, one of which is for velocity control, and the other is for position control. A PID controller controls the velocity of the media advance system until it reaches the predetermined switching position. When the media advance system passes the predetermined position, the controller is switched to the other PID controller which is more profitable for exact positioning. The switching position is determined by the estimated stop distance. The simulation and experimental results are presented to show the validity and effectiveness of the proposed controller.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.10 no.5
• /
• pp.509-522
• /
• 1998

An experimental investigation is reported on the heat transfer coefficient from a rotating flat plate in a round turbulent normally impinging water jet. Tests were conducted over a range of jet flow rates, rotational speeds, jet radial posetions with various combinations of three jet nozzle diameter. Dimensionless correlation of average Nusselt number for laminar and turbulent flow is given in terms of jet and rotational Reynolds numbers, dimensionless jet radial position. We suggested various effective promotion methods according to heat transfer characteristics and aspects. The data presented herein will serve as a first step toward providing the information necessary to optimize in rational manner the cooling requirement of impingement cooled rotating machine components.

• The Bulletin of The Korean Astronomical Society
• /
• v.44 no.1
• /
• pp.76.1-76.1
• /
• 2019

CTA 102, one of gamma-ray bright active galactic nuclei (AGN) has been observed with Korean very long baseline interferometry (VLBI) network (KVN) during the period of 2012 December-2018 May as part of interferometric Monitoring Of Gamma-ray Bright AGN (iMOGABA). Multi-frequency VLBI observations enable us to compare the milliarcsecond(mas)-scale iMOGABA images of relativistic jets with those from the Monitoring Of Jets in AGN with Very long baseline array (VLBA) Experiments (MOJAVE) and the VLBA-Boston University(BU)-BLAZAR programs which use VLBA with its angular resolutions of 0.2-1.3 mas. In spite of the relative larger beam sizes of KVN (1-10 mas), we are able to identify jet components of CTA 102 using the KVN multi-frequency VLBI observations with those resolved with VLBA. Considering an instrumental beam blending effect on the jet component identification, we were able to obtain a blending shift of the core position based on a convolution analysis using the VLBA data. When we apply the core position shift to the KVN images of CTA 102, we find that the identified jet components of CTA 102 from the KVN observations are well matched with those from the VLBA observations. Based on the results of the analysis, we may be able to study the jet kinematics and its correlation with gamma-ray flare activity.

• Proceedings of the KWS Conference
• /
• v.43
• /
• pp.213-215
• /
• 2004

Water jet propulsion system has high efficiency on middle to high speed, and it provides better safety than conventional screw propeller because it has not projected propeller and rudder. So many leisure boat and high-speed ferries use this propulsion system. We developed water-jet propulsion unit for small planning boat, and launched that in the boat, after that we tested water-jet unit in the lake. As a result, we certify heat dissipation at the bearing housing and reverse duct's shape for neutral position are important at the design, and alignment water-jet unit and keel line are important at the launching, and ship's resistance performance and jet's propulsion performance also are needed to consideration.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.7
• /
• pp.894-901
• /
• 2012

For more efficient use of the high pressure water-jet in rehabilitation of the water pipes, we have studied the water-jet cleaning motion of the in-pipe robot with screw drive. The mathematical models of the water-jet in the straight and the curved pipe (90 degrees elbow), representative features of the water mains, were designed to understand the water-jet motion and simulations have been performed. Furthermore the experiments has been conducted to validate the simulations by using the prototype in-pipe robot in the 3-D pipeline. The simulation results show that the water-jet motion in the straight pipe has a constant water-jet interval, whereas the motion in the curved pipe is changed by its position. By the comparison of the simulation and the experimental results, we have demonstrated that the simulations successfully estimate the water-jet motion inside the water pipes. Therefore in-pipe robot operators can predict a water-jet motion for a target water pipe through the simulation and flexibly make a proper water-jet motion by changing the robot configurations before a cleaning work.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.905-911
• /
• 2017

Effects of injector position and momentum flux ratio on a vertical jet in a cross flow field were studied qualitatively and shown by using air and water. The experiment was carried out by fixing the momentum flux ratio and varying the position of the injector hole. Conversely, the injector hole position was fixed and the momentum flux ratio was varied. Image visualization was performed by a Shadowgraph technique using a high speed camera. The visualized images were compared for finding differences in spraying through Density Gradient Magnitude Image. It is observed that as the x/d of the apparatus increased the jet break up height decreases and the spray angle also decreases. When x/d is 0, the spray reaches the floor and ceiling at any momentum flux ratio.