• 대한기계학회논문집B
• /
• 제27권4호
• /
• pp.496-503
• /
• 2003

An experimental study has been performed on thermal transport from an aluminum foam heat sink under a confined impinging air jet. Three kinds of aluminum foam heat sinks with 10, 20 and 40 PPI and a conventional pin-fin heat sink are tested in the present study. The jet Reynolds number is varied in the range of Re=667～5672 The effect of the confinement disk diameter and the distance between the confinement disk and the heater surface on the averaged Nusselt number is investigated in detail. The results are also compared with those of the unconfined impinging air jet. The critical distance, at which thermal performance shows a minimum compared to the unconfined jet impinging, will be described in terms of the Reynolds number and the pore density of the aluminum foam.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집B
• /
• pp.278-284
• /
• 2000

The method of Impinging jet was applied lots of part in industrial field as a cooling of as gas turbine blade, a annealing of metal and plastic sheets, drying of textile, veneer paper, X-ray medical devices, laser weapons and electronic components. This study's main factor is reciprocating Jet impingement perpendicular to the heated Surface. We researched the effect of heat transfer and enhancement with pulsating air jet. The pulsating air jet has an improvement in pulsating Frequencies((f= 0.5, 1, 1.5, 3Hz) and nozzle-to-plate distances($l/d=\;2{\sim}4,\;6{\sim}8,\;4{\sim}6,\;8{\sim}10$).

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.182-186
• /
• 2008

Fundamental experiments with single row heat exchanger were conducted for the purpose of validating new defrosting method using jet impingement. The coolant temperature were varied from 83 to 250 K. We used the jet periodically, once in 50 second and the duration of the jet is 0.1 second. The effect of the coolant temperature in the effectiveness of the jet defrosting was investigated.

• 설비공학논문집
• /
• 제14권6호
• /
• pp.441-449
• /
• 2002

Single-phase convection and partial nucleate boiling in free-surface and submerged jet impingements of subcooled water ejected through a 2-mm-diameter circular pipe nozzle were investigated by local measurements. Effects of jet velocity and nozzle-to-imping-ing surface distance as well as heat flux on distributions of wall temperature and heat transfer coefficients were considered. Incipience of boiling began from far downstream in contrast with the cases of the planar water jets of high Reynolds numbers. Heat flux increase and velocity decrease reduced the temperature difference between stagnation and far downstream regions with the increasing influence of boiling in partial boiling regime. The chance in nozzle-to-impinging surface distance from H/d=1 to 12 had a significant effect on heat transfer around the stagnation point of the submerged jet, but not for the free-surface jet. The submerged jet provided the lower cooling performance than the free-surface jet due to the entrainment of the pool fluid of which temperature increased.

• 대한기계학회논문집B
• /
• 제27권1호
• /
• pp.1-8
• /
• 2003

The heat transfer and flow measurements on a cylindrical pedestal mounted on a flat surface with a turbulent impinging jet were made. The experiments were made for the jet Reynolds number of Re = 23,000, the dimensionless nozzle-to-surface distance of L/d = 2~10, the dimensionless pedestal height of H/D = 0~1.5. Measurements of the surface temperature and the Nusselt number distributions on the plate surface were made using liquid crystal and shroud-transient technique. Flow measurements involve smoke flow visualization and the wall pressure coefficient. The results show that the wall pressure coefficient sharply decreases along the upper surface of the pedestal. However, the pressure increases when the fluid escapes from the pedestal and then collides on the plate surface. The secondary maxima in the Nusselt numbers occur in the region of 1.0 $\leq$ r/d $\leq$ 1.9. Their values for the case of H/D = 0.5 are maximum 80% higher than those for other cases. The formation of the secondary maxima may be attributed to the reattachment of flow on the plate surface which was separated at the edge of the pedestal.

• 대한기계학회논문집B
• /
• 제20권12호
• /
• pp.4013-4026
• /
• 1996

A numerical simulation has been carried out for the jet impinging on a flat plate and a semi-circular concave surface. In this computation finite volume method was employed to solve the full Navier-Stokes equation based on a non-orthogonal coordinate with non staggered variable arrangement. The standard k-.epsilon. turbulent model and low Reynolds number k-.epsilon. model(Launder-Sharmar model) with Yap's correction were adapted. The accuracy of the numerical calculations were compared with various experimental data reported in the literature and showed good predictions of centerline velocity decay, wall pressure distribution and skin friction. For the jet impingement on a semi-circular concave surface, potential core length was calculated for two different nozzle(round edged nozzle and rectangular edged nozzle) to consider effects of the nozzle shape. The result showed that round edged nozzle had longer potential core length than rectangular edged nozzle for the same condition. Heat transfer rate along the concave surface with constant heat flux was calculated for various nozzle exit to surface distance(H/B) in the condition of same jet velocity. The maximum local Nusselt number at the stagnation point occurred at H/B = 8 where the centerline turbulent intensity had maximum value. The predicted Nusselt number showed good agreement with the experimental data at the stagnation point. However heat transfer predictions along the downstream were underestimated. This results suggest that the improved turbulence modeling is required.

• 한국유체기계학회 논문집
• /
• 제18권2호
• /
• pp.60-66
• /
• 2015

Conjugate heat transfer analysis was performed to investigate the flow and cooling performance of the high pressure turbine nozzle of gas turbine engine. The CHT code was verified by comparison between CFD results and experimental results of C3X vane. The combination of k-${\omega}$ based SST turbulence model and transition model was used to solve the flow and thermal field of the fluid zone and the material property of CMSX-4 was applied to the solid zone. The turbine nozzle has two internal cooling channels and each channel has a complex cooling configurations, such as the film cooling, jet impingement, pedestal and rib turbulator. The parabolic temperature profile was given to the inlet condition of the nozzle to simulate the combustor exit condition. The flow characteristics were analyzed by comparing with uncooled nozzle vane. The Mach number around the vane increased due to the increase of coolant mass flow flowed in the main flow passage. The maximum cooling effectiveness (91 %) at the vane surface is located in the middle of pressure side which is effected by the film cooling and the rib turbulrator. The region of the minimum cooling effectiveness (44.8 %) was positioned at the leading edge. And the results show that the TBC layer increases the average cooling effectiveness up to 18 %.

• 에너지공학
• /
• 제23권3호
• /
• pp.21-26
• /
• 2014

유럽 원전 시장 개척을 위해 개발 중인 EU-APR1400은 중대사고 대처설비로 노외 노심용융물 보유 및 냉각을 위한 소위 Core catcher라 불리는 노외 노심용융물 냉각설비를 개발 중이며, Core catcher body를 노심용융물로부터 보호하기 위하여 노심용융물의 물성 및 상태를 변화시켜 냉각 및 보유에 유리하게 하는 희생물질을 설치한다. 중대사고 시 원자로 압력용기의 틈으로부터 노심용융물이 분출되어 희생물질에 충돌 시 열 전달량이 매우 증가하게 되므로, 이 때 노심용융물 제트의 충돌에 의한 희생물질의 침식율을 정확하게 예측하는 것은 매우 중요하다. 이 논문에서는 경계층 이론을 기반으로 한 희생물질 침식 모형을 제안하고 KAERI에서 수행한 실험결과와 비교하였다.

• 대한기계학회논문집
• /
• 제12권1호
• /
• pp.81-94
• /
• 1988

본 연구에서는 표면상태가 다양한 고온면을 충돌온류에 의하여 냉각하는 방식이 광범위하게 응용되고 있는 점에 유의하여 표면조도, 노즐직경 및 분류속도를 변화시키고 노즐끝에 전열면의 직경과 동일한 원형판을 부착하여 비철액체를 막고 문극내에 온류액체를 강제유동시킴으로써 열전달에 미치는 모든 영향을 실험에 의해 고찰하고 고찰하고 포화수온류에 의한 열류속의 무차원관계식을 도출하는 것을 본 연구의 목적으로 하였다.

• 태양에너지
• /
• 제15권2호
• /
• pp.47-64
• /
• 1995

등열유속상태(等熱流速狀態)를 유지(維持)하고 있는 수평 전열판이 회전하고 있을 때, 여기에 수분류가 충돌(衝突)할 경우의 열전달특성을 실험적으로 연구했다. 노즐직경(直經)과 전열면간(傳熱面間)의 거리(距離)를 일정(一定)하게 유지하고, 분류(噴流)레이놀즈수(數)와 회전(回轉)레이놀즈수(數)를 변화시키면서 이의 영향을 살펴보았다. 실험결과, 국소(局所)Nusselt수(數)를 국소회전(局所回轉)레이놀즈수(數), 분류(噴流)레이놀즈수(數), 분류(噴流)프란틀수(數), 무차원반경(無次元半徑)의 함수로 나타내었다.