• 한국자동차공학회논문집
• /
• 제14권2호
• /
• pp.151-157
• /
• 2006

The passenger car drivers want in general to feel good driveability, but they sometimes feel uncomfortable by shock and jerk phenomena when they push or release acceleration pedal with clutch on state. In this paper, the shock and jerk characteristics are studied on the vehicles controlled by the throttle-by-wire system. Experiments and simulations were carried out on two vehicles which show different control characteristics. The engine torque control characteristics was analyzed by measuring cylinder pressure. Various specification factors of the vehicles and the torque control logic of the engines were simulated through experimental data basis. The result shows the spring effect of the trans-axle in the drive-train is one of the most important factors of the shock-jerk phenomena and the engine torque control method is also responsible for the reducing the shock-jerk amplitude. In this paper a new control logic of the engine torque is suggested for the better driveablility on the tip-in/out event.

• 한국자동차공학회논문집
• /
• 제13권6호
• /
• pp.113-119
• /
• 2005

The passenger car drivers want in general to feel good driveability, but they sometimes feel uncomfortable by shock and jerk phenomenon when they push or release acceleration pedal with clutch engaged. In this paper, the shock and jerk characteristics are studied on the vehicles of the throttle-by-wire system. With this system, the throttle is not directly controlled by drivers but via a microprocessor. So the control logic of the throttle is very important on tip-in and tip-out driveability. Experiments were carried out on two vehicles which show different control characteristics. The torque control logics were analyzed by measuring cylinder pressures. The results show that special torque control logic is needed at tip-in/out state for good driveability.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.74-76
• /
• 2007

Generally, the dynamic parameters by dynamic simulation are calculated from an equivalent circuit parameters in design process. By performing dynamics of motors, it can be achieved design considering control pattern. In this paper, dynamic characteristics of LIM (Linear Induction Motors) is discussed using the new method of equivalent circuit parameters by field analysis. And the system response of VVVF(Variable Voltage Variable frequency) are presented for jerk characteristics represented as acceleration and deceleration by steep trust ripple.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.7-9
• /
• 2007

Generally, the dynamic parameters by dynamic simulation are calculated from an equivalent circuit parameters in design process. By performing dynamics of motors, it can be achieved design considering control pattern. In this paper, dynamic characteristics of LIM (Linear Induction Motors) is discussed using the new method of equivalent circuit parameters by field analysis. And the system response of VVVF(Variable Voltage Variable frequency) are presented for jerk characteristics represented as acceleration and deceleration by steep trust ripple.

• 한국철도학회논문집
• /
• 제6권4호
• /
• pp.286-293
• /
• 2003

The prototype of Korean high speed train (HSR350), composed of two power cars, two motorized cars and three trailer cars, has been designed, fabricated and tested. In this paper, the body vibration has been reviewed from the viewpoint of the vehicle's safety and the vibration limits for components and sub-assemblies mounted on the car-body using by the experimental method. And, the dynamic characteristics, such as jerk, natural mode and kinematic mode, have been reviewed. The KHST has been run to 300 km/h in the KTX line and the results of on-line test show that it has no problems in the vehicle's safety and the vibration limits. And the characteristics of body vibrations has been predicted at 350 km/h by fitting curve about the measured acceleration signals.

• 한국ITS학회 논문지
• /
• 제19권2호
• /
• pp.74-88
• /
• 2020

Cooperative-Intelligent Transport System(C-ITS)는 차량 대 차량 및 차량 대 인프라 무선 통신을 기반으로 교통사고예방을 목적으로 운전자에게 전방위험상황에 대한 정보를 제공한다. 또한 C-ITS 인프라에서 수집되는 차량의 주행행태 정보는 사고발생 개연성 분석을 통해 실시간 도로교통안전성 평가에 활용될 수 있다. 본 연구에서는 차량의 주행정보를 이용하여 도로의 교통안전성을 평가할 수 있는 방법론을 제시하였으며, 시뮬레이션 분석을 통해 방법론의 활용성을 검증하였다. 교통안전대체지표인 Jerk와 Stopping Distance Index(SDI)를 이용하여 개별차량의 주행 위험성을 분석하였으며, 위험성 분석결과를 집계하여 도로 구간별 안전성을 계량화하는 방법을 제시하였다. Jerk 기반의 안전성 평가 결과, 5% 이상의 차량 정보 샘플이 확보되면 본 연구의 방법론이 도로 구간의 교통안전성 평가에 적용 가능한 것으로 분석되었다. 한편, SDI의 경우에는 20% 이상의 샘플이 요구됨을 확인하였다. 이러한 결과는 일정 수준 이상의 사업용차량 센서 자료로 수집된 Jerk와 SDI가 도로 구간의 안전성을 대표할 수 있음을 의미한다. 본 연구의 결과물은 도로의 교통안전성을 실시간으로 평가하고 모니터링하는 시스템 개발의 핵심요소로 활용될 것으로 기대된다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국제학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.212-217
• /
• 1993

In this paper, characteristics of the motions of a human arm are investigated experimentally. When the conditions of the target point are restricted, human adjusts its trajectory and velocity pattern of the arm to fit the conditions skillfully. The purpose of this work is to examine the characteristics of the trajectory, velocity pattern, and the size of the duration in the following cases. First, we examine the case of point-to-point motion. The results are consistent with the minimum jerk theory. However, individual differences in the length of the duration can be observed in the experiment. Second, we examine the case which requires accuracy of positioning at the target point. It is found that the velocity pattern differs from the bell shaped pattern explained by the minimum jerk theory, and has its peak in the first half of the duration. When higher accuracy of the positioning is required, learning effects can be observed. Finally, to examine the case which requires constraint of the arm posture at the target point, we conduct experiments of a human trying to grasp a cup. It is considered that this motion consists of two steps : one is the positioning motion of the person in order to start the grasping motion, the other is the grasping motion of the human's hand approaching toward the cup and grasping it. In addition, two representative velocity patterns are observed : one is the similar velocity pattern explained in the above experiment, the other is the velocity pattern which has its relative maximum in the latter half of the duration.

• 전력전자학회논문지
• /
• 제5권5호
• /
• pp.515-521
• /
• 2000

본 논문은 전동차용 추진장치인 IGBT VVVF 인버터의 현차시험에 관한 것이다. IGBT VVVF인버터는 1,650kVA급으로 개발되었다. 추진 인버터의 신뢰성과 성능을 확인하기 위하여 서울시 지하철 6호선에서 본선시험을 하였다. 시험 차량구성은 4M4T로 구성되었으며, 전장품은 4대의 VVVF인버터, 16대의 견인전동기 및 2대의 SIV로 구성하였다. 추진장치는 1C4M으로 구성하였다. 현차시험을 통하여 추진용 인버터의 우수한 가·감속 능력과 가가속도 특성 및 구배에서의 등판능력을 확인 할 수 있었다.

• 한국생산제조학회지
• /
• 제19권5호
• /
• pp.596-602
• /
• 2010

In this study, a fmite element model was developed for analysis of feeding a structure in open loop control The finite element analysis (FEA) can simulate dynamic behavior of the structure of a machine tool rapidly traveling with a screw feeding driving system. The feeding mechanism was implemented with screw element of the FEA tool used in this study. The procedure was developed for the dynamic transient FEA. First, motion parameters such as jerk and velocity were introduced for the structure to be fed in open loop control When its traveling distance was determined, set-points for the distance were generated based on the motion parameters. The set-points were applied to the FE model constructed for the traveling structure. The FEA was executed and evaluated. In this study, the FEA procedure was applied to the column of a machine tool and the dynamic behavior of the column was evaluated. The FEA helps in evaluation of the motion characteristics of a structure. The convergence time of the structure vibration posterior to feeding termination can be estimated and the stiffness of the flexible structure is also evaluated against jerk, and acceleration. It provides the feeding force which is helpful in selection of the feeding motor.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.25.3-25
• /
• 2001

This paper describes a control method of a robot cooperating with a human. A task in which a robot and a human move an object cooperatively is considered. To develop the force controller of the robot, the characteristics of human arm are investigated. The arm is forced to move along a trajectory in the experiment and the exerted force and the displacement are analyzed, It is found the force characteristics of the human arm is regarded as an optimal damper with minimizing a cost function. Then, the model is implemented to a robot and the cooperation of the robot and a human operator is examined. The effectiveness of the derived model is investigated and the experimental results show that the human moves the object supported by the robot with a minimum jerk trajectory.