• Journal of Korean Association for Spatial Structures
• /
• v.17 no.3
• /
• pp.65-73
• /
• 2017

Recently, the trend is emerging a variety of irregular tall buildings. It is important to design the building for lateral load according to this trend. Fluid Structure Interaction(FSI) simulation can be performed to understand the vibrations of the structure against dynamic wind loads. In order to make the physical characteristics of the actual structure and the analytical model the same, we studied core inserting equivalent stiffness modeling method. As a result of this analysis, the stiffness of the structure can be set similar to that of the two axes of the structure, and turbulence can be reproduced through the acceleration tendency.

• Journal of Korean Association for Spatial Structures
• /
• v.17 no.3
• /
• pp.75-82
• /
• 2017

The Kingery-Bulmash equation is the most common equation to calculate blast load. However, the Kingery-Bulmash equation is complicated. In this paper, a modified equation for surface blast load is proposed. The equation is based on Kingery-Bulmash equation. The proposed equation requires a brief calculation process, and the number of coefficients is reduced under 5. As a result, each parameter obtained by using the modified equation has less than 1% of error range comparing with the result by using Kingery-Bulmash equation. The modified equation may replace the original equation with brief process to calculate.

• Proceeding of KASS Symposium
• /
• 2006.05a
• /
• pp.214-223
• /
• 2006

Membrane structures, a kind of lightweight soft structural system, are used for spatial structures. The material property of the membrane has strong axial stiffness, but little bending stiffness. The design procedure of membrane structures are needed to do shape finding, stress-deformation analysis and cutting pattern generation. In shape finding, membrane structures are unstable structures initially. These soft structures need to be introduced initial stresses because of its initial unstable state, and happen large deformation phenomenon. Therefore, in this study, to find the structural shape after large deformation caused by initial stress, we need the shape analysis considering geometric nonlinear term. And we investigate the evaluation of shape analysis technique's convergence and efficiency according to the control method

• Proceeding of KASS Symposium
• /
• 2006.05a
• /
• pp.205-213
• /
• 2006

Membrane structures, a kind of lightweight soft structural system, are used for spatial structures. The design procedure of membrane structures are needed to do shape finding, stress-deformation analysis and cutting pattern generation, because the material property has strong axial stiffness, but little bending stiffness. The problem of cutting pattern is highly varied in their size, curvature and material stiffness. So, the approximation inherent in cooing pattern generation methods is quite different. Therefore the ordinary computer software of structural analysis & design is not suitable for membrane structures. In this study, we develop the program for cutting pattern generation using geodesic line, and investigate the result of example's cutting pattern in detail.

• Journal of Korean Association for Spatial Structures
• /
• v.21 no.1
• /
• pp.51-59
• /
• 2021

In this paper, the effect of the turbulence intensity in across-wind direction on the wind load in CFD(Computational fluid dynamics) simulation was analyzed. 'Ansys fluent' software was used for CFD simulation. And the fluctuating wind speed applied to the simulation was generated according to Korean Design Standard and Von Karman wind turbulence model. The turbulence intensity in across-wind direction for simulation was applied from 0 to 100% of the turbulence intensity in along-wind direction. The analysis results showed that the turbulence intensity in across-wind direction had a particularly great effect on the wind load in across-wind direction.

• Child Health Nursing Research
• /
• v.23 no.3
• /
• pp.319-328
• /
• 2017

Purpose: This study was conducted to identify factors affecting health promotion behaviors of upper grade elementary students. Methods: A descriptive study was carried out with 282 fifth or sixth elementary school students from two cities, Korea. Data were collected using self-administrative questionnaires containing items on health knowledge, attitudes, subjective norms, perceived behavior control and health promotion behavior, and analyzed using descriptive statistics, t-test, ANOVA, Cronbach's ${\alpha}$, Pearson Correlation Coefficients, and multiple regression analysis with the SPSS/WIN 21.0 program. Results: There were significant positive correlations between health promotion behavior and health knowledge (r=.36, p<.001), attitudes (r=.41, p<.001), subjective norms (r=.36, p<.001), perceived behavior control (r=.49, p<.001). Perceived behavior control (${\beta}=.38$, p<.001), health knowledge (${\beta}=.26$, p<.001), perceived health status - good (${\beta}=.15$, p=.005) were significant factors affecting health promotion behavior and explained 31%(F=43.29, p<.001) of variance. Conclusion: Results indicate that level of health promotion behavior is appropriate and perceived behavior control is the most important factor for health promotion behavior among the predictors. These findings also suggest that it is necessary to promote perceived behavior control and health knowledge in developing health promotion intervention programs for these students, as well as a need to strengthen education on sex behavior and health, accident prevention and first aid.

• Journal of Korean Association for Spatial Structures
• /
• v.19 no.4
• /
• pp.95-102
• /
• 2019

In this study, the reliability of the analysis is evaluated by comparing the average wind pressure coefficient, RMS wind pressure coefficient and wind pressure spectrum with same condition of wind tunnel test which are calculated in the high-Reynolds number range of 1.2×10⁶, 2.0×10⁶ each for the typical curved shape dome structure. And it is examined by the reliability of analysis through Improved delayed detached Eddy Simulation(IDDES), which is one of the hybrid RANS/LES techniques that can analyze the realistic calculation range of high Reynolds number. As a result of the study, it was found that IDDES can be predicted very similar to the wind tunnel test. The distribution pattern of the wind pressure coefficient and wind pressure spectrum showed a similar compared with wind tunnel test.

• Journal of the Korean Institute of Educational Facilities
• /
• v.23 no.1
• /
• pp.13-22
• /
• 2016

Recently, Korea has been established and operated International Schools manifesting to improve the nation's capacity of the foreign languages skill and to cultivate internationally trained professional manpower. In order to achieve the vision of a world-class educational organization, it has to be designed for the facility standards to meet the international accreditation standards. Therefore, the main purpose of this study is to research about basic resources through comparison of facility conditions between public schools in Korea and international accredited schools. By comparing those two different plan drawings are found the following things. First, Schools which established with International Accreditation Standard are prepared detailed criteria for the facility, Furthermore information about the furnishings included, in addition to specific equipments for classes are stated to be prepared. Secondly, it is more effective when special classrooms such as music and science are equipped with various spatial elements, enough educational equipment storage, teacher's study rooms, practical training rooms and student's activity rooms to support various teaching programs and learning efficiently. Lastly, there was a clear tendency that not only hardware but also software standards for the audiovisual room and library have been more enhanced to enable multidisciplinary educational approaches with the recent education training trend.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.5
• /
• pp.104-108
• /
• 2009

In this paper, we investigate the performance of ARQ-aided downlink Time Switched Transmit Diversity (TSTD) in the WCDMA LCR-TDD system. Proposed TSTD system applies the ARQ scheme in which the receiver sends the response signal (ACK or NACK signal) to the transmitter and predicts the channel condition based on response signal after receiver checks the error, then it re-sends data. Simulation results demonstrate that the proposed TSTD scheme yields about 5.5dB performance gain, compared with the conventional TSTD in term of the frame error rate(FER) for a mobile speed of 3km/h and an FER value of 1%. In addition, 7% of throughput gain is shown when Eb/N0=7dB.

• Journal of Korean Association for Spatial Structures
• /
• v.16 no.4
• /
• pp.59-66
• /
• 2016

Recently damage of structures and loss of life by terrorism are internationally increasing. Among these terror that have a possibility to can happen in korea and that can caused lot of human life loss is the vehicle terror. To prevent the vehicle terror, the anti-ram barriers are needed. But domestic standard about anti-ram barriers are not clear. So, in this study, we will utilize and analyze the vehicle impact to evaluate the efficiency of the domestic bollard and suggest the installation standard of those. In Korea, granite, elastic, steel and stainless bollard are used. The performance of those bollard is not available. Elastic bollard couldn't stop the vehicle, and the others just could stop the vehicle only at the speed under 10kph. Therefore, set the variable to reinforce, and evaluate the defence efficiency of bollard. As a result, granite and elastic bollard was not suitable for the anti-ram barriers. Performance of steel bollard increased as thickness grew. So steel bollard should must be thicker than 10T. And the concrete compressive strength effected insignificantly on the defence efficiency, so more than 24MPa compressive concrete be used. Performance of stainless bollard increased as thickness grew. So stainless bollard should must be thicker than 13T.