• Korean Journal of Optics and Photonics
• /
• v.34 no.6
• /
• pp.241-247
• /
• 2023

We examine the spectral characteristics of laser-induced periodic surface structures (LIPSSs) formed on an amorphous silicon film irradiated by a 355-nm nanosecond laser. A Gaussian beam with a diameter of 196 ㎛ is used to perform a two-dimensional raster scan. The laser's pulse number is varied from 190 to 280, and its intensity is adjusted within 100-130 mJ/cm². LIPSSs with a periodicity of approximately 330 nm form on the surface of the Si film, aligned perpendicular to the laser's polarization. Transmission spectra of the samples show dips around 700 nm for transverse electric polarization and around 500 nm for transverse magnetic polarization. The features are investigated with a one-dimensional-grating model using a rigorous coupled-wave analysis. Simulations confirm that the observed dips are due to the resonant modes, depending on the polarization.

• Resources Recycling
• /
• v.15 no.3 s.71
• /
• pp.38-45
• /
• 2006

The thermal filter press dewatering(TFPD) technology to improve the dewaterability through increasing the inner vapor pressure, lowering the filtration viscosity and forming the porosity easily within cake as applying the heat at the sludge layer was developed in this study. The hot water with temperature of $95^{\circ}C$ and pressure of $1.2kg_f/cm^2$ was supplied to the heating plate equipped between filter plates with plate size of $470{\times}470mm$ and material of polypropylene. Sludge was dewaterd by supplying pressure of $5kg_f/cm^2$ and then by squeezing pressure of $15kg_f/cm^2$. As a results of estimating the characteristics of thermal dewatering to consider the initial water content and organic content to be influenced by a period of water shortage and rainwater, the dewatered cake water content was about 35 wt% and dewatering velocity was $4DSkg/m^2{\cdot}hr$ under the rainwater period, and the dewatered cake water content was about 50 wt% and dewatering velocity was $1.5DSkg/m^2{\cdot}hr$ in the case of sludge of water shortage season. These results was superior to the mechanical dewatering performance with water content of 70wt% and dewatering velocity of $0.9DSkg/m^2{\cdot}hr$. On the base of the results of TFPD, energy consumpted to deal with DS(Dry Solid) of 1kg was estimated by 300 kJ. It was analyzed that the energy consumption of TFPD was decreased about one third with comparison to the dryer system. Dewatering velocity of this technology was faster than the one of mechanical dewatering equipment and it was easier to product low water content cake. Therefore, this technology was recognized that dewaterability was predominant because of the fast of dewatering velocity and production of low water content cake, and also this known as economical efficiency was excellent because of low energy consumption in comparison with dryer.

• Journal of the Korean Vacuum Society
• /
• v.16 no.6
• /
• pp.483-488
• /
• 2007

Current feeder system (CFS) for Korea superconducting tokamak advanced research(KSTAR) project plays a role to interconnect magnet power supply (MPS) and superconducting (SC) magnets through the normal bus-bar at the room temperature(300 K) environment and the SC bus-line at the low temperature (4.5 K) environment. It is divided by two systems, i.e., toroidal field system which operates at 35 kA DC currents and poloidal field system wherein 20$\sim$26 kA pulsed currents are applied during 350 s transient time. Aside from the vacuum system of main cryostat, an independent vacuum system was constructed for the CFS in which a roughing system is consisted by a rotary and a mechanical booster pump and a high vacuum system is developed by four cryo-pumps with one dry pump as a backing pump. A self interlock and its control system, and a supervisory interlock and its control system are also established for the operational reliability as well. The entire CFS was completely tested including the reliability of local/supervisory control/interlock, helium gas leakage, vacuum pressure, and so on.

• Korean Journal of Occupational Health Nursing
• /
• v.8 no.1
• /
• pp.22-41
• /
• 1999

This study intended to analyze the health promoting behaviors, compare their factors according to the shift pattern of duties of women workers who were working in the industrial workplace and present basic data in planning systematic and effective programs of health promotion for three-shift system and day-duty. Using Quota Sampling, 219 women workers were selected as subjects from 5 workshops which had 50 settled workers up to 300 and 10 factories which had more than 300 located in Taegu and Kyung-Book Province. Data were collected by means of questionnaire from September 12 to September 30, 1998. As the instruments of the study were used Health Promotion Lifestyle Profile(HPLP) which was adapted and adjusted by Seo, Y. O. for health promoting behavior, the one developed by Moon, J. S. (1990) for health-belief, the one developed by Sherer et al.(1982) and then adapted by Oh, H. S. for self-efficacy, and the one developed by Park, J. W. (1985) for social support. The analysis of data were performed with Cronbach's ${\chi}^2$-test, t-test, ANCOVA, Kendal tau, Pearson correlation, Stepwise Multiple Regression test using SPSS program. The results of the study are as follows : 1. There was a significant difference in age(${\chi}^2=32.46$, p=0.000), career (${\chi}^2=18.47$, p=0.000), working day(t=-3.18, p=0.000) by the shift pattern of duties in terms of socio-demographic characteristics. 2. There was a statistically significant difference between the two groups on the health promoting behaviors (t=2,52, p=0.012). The score of three-shift group on health promoting behaviors was 2.27, showing that it was lower by .13 than that of day-duty group(2.40). 3. ANCOVA involving age, career and working day as covariables, which had revealed significant difference before, showed that health promoting behaviors by the shift patterns of duties was significantly different(F=4.88, p=0.028). 4. In consideration of variables that have an influence on health promoting behavior by the shift pattern of duties, social support occupied 19.4% of health promoting behavior in the three-shift group and 22.5% including the sense of self-efficacy. In the day-duty group, social support occupied 34.4% of health promoting behavior. 5. The score of three-shift group(2.94) was significantly lower than that of day-duty group(3.12) in the perceived benefit of health-belief(t= -3.29, p=0.001), while the score of three-shift group (2.48) was significantly higher than that of day-duty group(2.24) in the perceived barrier (t=4.22, p=0.000). In the sense of self-efficacy(t=-4.20, p=0.000), the score of three-shift group(3.24) was significantly lower than that of day-duty group(3.53) while in social support(t=-4.56, p=0.000) the one of three-shift group(2.64) was significantly lower than that of day-duty group(2.88). The suggestions are as follows on the basis of the results of this study : 1. It is required to develop health promoting program that takes the shift pattern of duties of women workers into consideration. In addition, there are special demands on developing nursing strategies for health promoting behavior of three-shift workers. 2. It is required to develop specific strategies for social support which is the most significant factor to the health promoting behavior for women workers. 3. It is necessary to develop some programs for improving the sense of self-efficacy, social support, and health-belief of three-shift workers. To achieve these tasks, industrial nurses should play an active role and improve the ability of self-health care of women workers.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.10 no.4
• /
• pp.235-243
• /
• 2007

In order to understand the water mass properties in the southern location of the East Sea in the Korean coasts, the vertical distributions (down to 2,000 m deep) of water temperature, salinity, and dissolved inorganic nutrients were determined in April of 2005. The water mass of the surveyed location showed distinct vertical layers; highly saline surface, surface mixing layer, and thermocline of low temperature and salinity. The water layer below 300 m was characterized by water temperature lower than $1^{\circ}C$ and salinity 34.06, showing a representative water mass of the East Sea. The inorganic nutrients rapidly increased from 200m in the northern and southern parts around Ulleung Basin. A marked environmental difference was found between two layers separated by thermocline. The upper layer of the thermocline was oligotrophic and the vertical distribution of nutrient was very stable. In the water layer between 100 and 200m the nutrients slightly increased but remained still stable. From southern coasts to northeastern Ulleung, the water mass properties were site specific; the thickness of the surface mixed layer and nutricline showed a trend diminishing toward the northern locations probably due to diminished influence of Tsushima water. Redfield ratio (N:P=16:1) based on the ratio of chemical composition in organism revealed that nitrogen value continuously decreased to less than 16 with the water depth down to loom from the thermocline. The value in the water layer deeper than 100 to 200 m, thereafter, showed an increasing trend (over 16). This result was further supported by the finding of lower chlrophyll a content in the layer.

• Korean Journal of Heritage: History & Science
• /
• v.44 no.4
• /
• pp.142-153
• /
• 2011

'Silla Monument Stone in Jungseong-ri, Pohang' was discovered in Pohang City, Gyeongsangbuk Province of Korea in 2009. The monument stone with irregular shape has dimensions of maximum height of 105cm, width of 47.6~49.6cm, thickness of 13.8~14.7cm and weight of 115kg. The results of monument stone was found to be granitite. Conservation treatment procedure was carried out in the order of production of Weathering map, cleaning of surface pollutants, consolidation using ethyl silicate. Black pollutant(crust) that covered more than 60% of the surface was analyzed first in order to remove the pollutants on the surface of the monumental stone by cleaning of surface pollutants using laser. The purpose on analysis was not only to verify the pollutants on the stone but also to carry out preliminary cleaning by securing rocks with same pollutant as the monumental stone. As the results of analysis using p-XRF(PMI. INNOV-X, USA) on the site, high level of Mn and Fe were detected, and the analysis of small section that had been fallen off with SEM/EDX for the purpose of quantitative analysis also detected high level of Mn. The Similar contaminants on Stone secured in the manner described above were made into 10 samples ($5cm{\times}5cm$) and was subjected to preliminary cleaning by Nd-YAG Laser(Laser&Physics, Korea). The results of surface observation through portable microscope during cleaning revealed that the power of 460mJ, wavelength of 1064nm and irradiation frequency of 1,800~2,300 per $25cm^2$ were most effective. Evaluation on the preservative treatment was made through confirmation of the extent of removal through color-difference meter measurement and component analysis prior to and following removal of the pollutants. As the result of color-difference meter measurement increase in the brightness was evidenced by the increase in the brightness ($L^*$)value from 33 to 49, and it was possible to ascertain the reduction in the pollutants as the content of Mn was reduced by about 80% from $50,000{\pm}5,000ppm$ to $10,000{\pm}2,000pmm$ from the result of component analysis.

• Journal of the Korean Society of Radiology
• /
• v.16 no.1
• /
• pp.67-75
• /
• 2022

The aim of this study is to establish a new QC method that can simultaneously evaluate the resolution of the x/y plane and the z-axis by producing a phantom that can reflect exposure and reconstruction parameter of MDCT system. It was used with Aquilion ONE(Cannon Medical System, Otawara, Japan), and the examination was scanned using of 120 kV, 260 mA, and the D-FOV of 300 mm². It produced new SSP phantom modules in which two aluminum plates inclined at 45° to a vertical axis and a transverse axis to evaluate high contrast resolution of x/y plane and z axis. And it changed factors such as the algorithm, distance from gantry iso-center. All images were reconstructed in five steps from 0.6 mm to 10.0 mm slice thickness to measure resolution of x/y plane and z-axis. The image data measured FWHM and FWTM using Profile tool of Aquarius iNtusion Edition ver. 4.4.13 P6 software(Terarecon, California, USA), and analysed SPQI and signal intensity by ImageJ program(v1.53n, National Institutes of Health, USA). It decreased by 4.09~11.99%, 4.12~35.52%, and 4.70~37.64% in slice thickness of 2.5 mm, 5.0 mm, and 10.0 mm for evaluating the high contrast resolution of x/y plane according to distance from gantry iso-center. Therefore, the high contrast resolution of the x/y plane decreased when the distance from the iso-center increased or the slice thickness increased. Additionally, the slice thicknesses of 2.5 mm, 5.0 mm, and 10.0 mm with a high algorithm increased 74.83, 15.18 and 81.25%. The FWHM was almost constant on the measured SSP graph for evaluating the accuracy of slice thickness which represents the resolution of x/y plane and z-axis, but it was measured to be higher than the nominal slice thickness set by user. The FWHM and FWTM of z-axis with axial scan mode tended to increase significantly as the distance increased from gantry iso-center than the helical mode. Particularly, the thinner slice thickness that increased error range compare with the nominal slice thickness. The SPQI increased with thick slice thickness, and that was closer to 90% in the helical scan than the axial scan. In conclusion, by producing a phantom suitable for MDCT detectors and capable of quantitative resolution evaluation, it can be used as a specific method in the management of research quality and management of outdated equipment. Thus, it is expected to contribute greatly to the discrimination of lesions in the field of CT imaging.

• Reproductive and Developmental Biology
• /
• v.29 no.3
• /
• pp.169-174
• /
• 2005

This study was comducted to examine the effects of culture medium, and the osmolarity and osmotic change of the culture medium on in vitro maturation of porcine oocytes and developement of porcine parthenogenetic embryos. In Experiment 1, cumulus-oocyte complexes were matured in NCSU-23, mWM and mKRB, respectively, There was no difference in maturation rate($62.1\~71.3\%$) among groups. In Experiment 2, matured oocytes in each medium were activated and cultured for 6 days in the same media. Blastocyst formation rate was higher in NCSU-23($22.9\%$) than those of others($0\~0.6\%$, P<0.05). In Experiment 3, parthenogenetic embryos were cultured for 6 days in NCSU-23 with different osmolarity(300, 280 and 256 mOsmols) adjusted by NaCl. There were no differences in development rates to the blastocyst stage($11.0\~14.4\%$) among groups. In Experiment 4, activated oocytes were cultured for 2 days in NCSU-23 with 300, 280 and 256 mOsmols and then transferred to increased or decreased osmotic condition. Blastocyst formation rate was higher in a group which was transferred from the higher osmotic condition to the lowe. osmotic condition($21.0\%$) than a contrary group( $11.8\%$, (P<0.05). This result shows that the culture medium and the osmolarity of the culture medium affect the development of porcine parthenogenetic embryos, and the change of osmolarity from the higher condition to the lower condition at a certain developmental stage can enhance the development of porcine parthenogenetic embryos.

• Korean Journal of Poultry Science
• /
• v.32 no.3
• /
• pp.149-156
• /
• 2005

Two experiments were conducted to examine the effects of betaine intake on blood and yolk cholesterol, abdominal fat, liver fat, tissue triglyceride(TG) and liver HMG-CoA reductase In laying hens. In Expt. 1, a total of 72 ISA-brown laying hens were individually assigned into four treatments from 18 to 21 weeks old. Com-soybean meal based diet were fed with the addition of 0, 300, 600 and 1,200ppm. In Expt. 2, 72 ISA-brown laying hens were housed into individual cage to evaluate the effect of dietary betaine(0, 600ppm) and energy(ME, 2,800, 2,900kca/kg) from 70 to 74 weeks. Serum total cholesterol, LDL and HDL-cholesterol and TG concentration in blood of hens fed betaine tended to increase compared to those of the control, but were not significantly different. However, betaine supplementation showed a statistically significant decrease in yolk cholesterol(P<0.05). There was no significant difference in abdominal fat among the treatments. Liver fats and 7c of birds 130 betaine was decreased compared with control. Serum total cholesterol, LDL-cholesterol and triglyceride concentration were significantly inc.eased by ffeding a diet containing 600ppm betaine in Expt. 2(P<0.05), but were not influenced by the dietary energy levels. Yolk cholesterol, abdominal fat and HMG-CoA reductase activity were affected neither by dietary energy nor betaine level.

• Journal of Periodontal and Implant Science
• /
• v.26 no.4
• /
• pp.989-1002
• /
• 1996

The purpose of this study was to determine the effect of a pulsed Nd:YAG laser irradiation on human gingival tissues. The patients, who were planned to be treated by clinical crown lengthening procedure and gingivectomy, were selected. All the patients received oral hygiene instruction, scaling and root planing at preoperation. The crest of gingival tissue on upper and lower anterior teeth was irradiated by a pulsed Nd:YAG laser(El. EN. EN060, Italy) with a fiber optic of 300 m in contact mode for 20 seconds. Gingival tissues were divided into 4 groups according to the laser power of 1.0W(10Hz, 100mJ), 2.0W(20Hz, 100mJ), 3.0W(30Hz, 100mJ) and 4.0W(40Hz, 100mJ). Immediately after the laser irradiation, the specimens were excised, fixed 10% neutral formalin, sectioned $4-6{\mu}m$ thick, stained by Hematoxylin-Eosin and Periodic Acid Schiff stain and observed under light microscope. The removed tissue depth and the coagulated layer depth due to a laser irradiation by a laser irradiation were measured on the microphotographs. The difference of measurements according to the different laser power was statistical1y analyzed by Kruskal Wallis Test with SAS program. The results were as follows : 1. In histologic findings of irradiated gingival tissues; a. In the irradiated gingival specimen with 1.0W laser power, some vesicles were observed in limited superficial layer of gingival epithelium. b. In the irradiated gingival specimen with 2.0W and 3.0W laser power, the epithelium was almost removed except for the traces of viable basal cell remnants at ret peg, and coagulation necrosis related with the thermal effect of laser was noted. c. In the irradiated gingival specimen with 4.0W laser power, complete removal of epithelium, partial removal of underlying connective tissue, and the coagulation necrosis of subjacent gingival tissue were shown. 2. The removed tissue depth was deeper in the irradiated specimens with higher power. There was a statistical significance in the difference of removed tissue depth between 1.0W group ($44.54{\pm}6.99um$) and 3.0W group ($99.75{\pm}6.64{\mu}m$), and between 1.0W group($44.54{\pm}6.99{\mu}m$) and 4.0W group($111.36{\pm}4.50{\mu}m$), and between 2.0W group($98.01{\pm}4.53{\mu}m$) and 4.0W group($111.36{\pm}4.50{\mu}m$)(P<0.05). 3. The coagulated layer depth was deeper in the irradiated specimens with higher power. There was a statistical significance in the difference of coagulated layer depth between 1.0W group($31.82{\pm}8.99{\mu}m$) and 3.0W group($55.99{\pm}20.94{\mu}m$), and between 1.0W group($31.82{\pm}8.99{\mu}m$) and 4.0W group($83.68{\pm}10.34{\mu}m$)(P<0.05). From this study, the results demonstrated that the effects of a pulsed Nd:YAG laser irradiation on gingival tissues seemed to depend on the laser power and that the irradiation with high power could be harmful to adjacent healthy tissue.