• Elastomers and Composites
• /
• v.28 no.4
• /
• pp.283-292
• /
• 1993

The morphology and impact strength of alloys of high density polyethylene(HDPE) and nylon-6(PA) with modified $ethylene-{\alpha}-olefin$ copolymer(OCP) as compatibilizer and impact modifier were measured by the scanning electron microscope(SEM) and the notched Izod impact test(and the high rate impact test), respectively. HDPE is incompatible with PA and specimens obtained from simple mechanical mixing show the inferior properties. However, it was indicated that OCP played roles of not only impact modifier but also compatibilizer. High rate impact test results were different from those of the notched Izod impact test, but in both tests OCP was effective for HDPE/PA blends. From SEM observation, the size of the dispersed phase in alloys prepared with OCP is much smaller than that of alloys without OCP and the interfacial adhesion of alloys prepared with OCP is also better. Toughening mechanism of polymer blends was discussed by combining the morphology analysis with mechanical and thermal properties.

• Elastomers and Composites
• /
• v.48 no.2
• /
• pp.172-179
• /
• 2013

Impact modifier reinforced polymers are frequently used. In this study, Izod impact test has been simulated to analyze the mechanism of impact reinforcement of Nylon6 which contains impact modifier. The modeling of rubber particles added to Nylon6 as an impact modifier has been attempted. Based on the modeling, simulation of Izod impact test has been performed to observe the distribution and direction of stress at the cross-section of impact specimen. Three computer simulation models for Nylon6 were investigated. Those were without impact modifier, containing impact modifier without surface treatment, and containing impact modifier with surface treatment in the Nylon6. Simulation results showed that the stress which originated at the notch surface propergated to the inside of specimen round a impact modifier. In addition to that, impact modifier reinforced Nylon6 specimen showed low stress ditribution in the cross-section specially at notch surface. Principal stress in perpendicular direction to crack was also lowered in impact modifier reinforced Nylon6. These enhanced impact resistance reduced and crack propergations. Through this study it was realized that the computer simulation can be utilized to investigate the property enhacement of composite materials.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.3
• /
• pp.461-470
• /
• 2002

The present paper investigates the effect of hot isostatic pressing (HIPing) on mechanical properties, e.g., tensile strength, ductility and impact absorption energy of sand and die casted aluminum alloys. After HIPing at various temperatures and pressure conditions, uniaxial tensile test and Izod impact test of the samples were carried out. The experimental results showed improvements in uniaxial tensile strength, elongation and Izod impact toughness of sand casted aluminum alloy, while deterioration of a tensile strength fur die casted aluminum alloy. The effect of HIPing for microstructure of the cast aluminum alloy was also investigated.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.136-142
• /
• 2018

Additive manufacturing process technology, known as the 3D printing process, is expanding its utilization from simple model realization to commercialized part production based on continuous material development. Recently, research and development have been actively carried out to fabricate lightweight and high-strength parts using polymers, such as polyamide (polyamide), which is a high-strength engineering plastic material. In this study, the Izod impact characteristics were analyzed for polyamide 12 (PA12) materials. For the specimen production, selective laser sintering process technology, which has excellent mechanical properties of finished products, was applied. In addition, PA12 and glass bead reinforced PA12 materials were produced. The specimens were classified according to the production direction on the production platform, and each specimen was subjected to an Izod test at test temperatures of $-25^{\circ}C$, $25^{\circ}C$, and $60^{\circ}C$. As a result, the impact strength of PA12 and glass bead-reinforced PA12 of vertical direction specimens were 48.8% and 16.3% lower than those of the parallel specimens at a $25^{\circ}C$ test temperature and the impact strength of parallel specimens was improved by 46.5% and 20.4% at a test temperature of $60^{\circ}C$ compared to that at $-25^{\circ}C$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.7
• /
• pp.4653-4658
• /
• 2014

A study of the improvement in the impact strength is required to apply Nylon 66/silicate composites as an automobile material. Nylon 66/silicate composites were prepared using a twin screw extruder in case of a silicate treatment by ${\gamma}$-APS (S-silicate) and the addition of an octene ${\alpha}$ olefin grafted by maleic anhydride (PE-g-MAH). The chemical structure of the silane treated silicate was measured by Fourier transform infra-red (FT-IR) spectroscopy. The chemical reaction was confirmed by the decrease in the FT-IR intensity of the OH stretching vibration. The thermal properties, intercalation structure, and Izod impact strength were measured by DSC, TGA, XRD, and Izod impact tester. There was no significant effect on the degradation temperature of the Nylon66/silicate composite, but the crystallization temperature and crystallinity increased slightly in the case of the Nylon66/silicate composites. This suggests that the additives act as heterogeneous nuclei on the Nylon 66 matrix. The Izod impact test indicated that S-silicate enhanced the impact performance by up to 24%.

• Composites Research
• /
• v.26 no.5
• /
• pp.303-308
• /
• 2013

Carbon fiber (CF) reinforced polypropylene (PP) compositeis was increased to amount consumed. In this study, recycle of composites by recycle times. CF was containing 20%. Mechanical and interfacial propertis of CF/PP was evaluation for number of recycle time. Mechanical assessment of CF/PP was tension, bending, fatigue tension test and izod test method. Interfacial assessment of CF/PP was wettability test and FE-SEM of fracture surface method. Fiber and matrix was changed to recycle time. The more recycle of CF/PP, the more interfacial bonding was decreased. Because fiber and matrix was damaged to thermal damage. And then reinforced CF was shorter than original shape.

• Elastomers and Composites
• /
• v.45 no.2
• /
• pp.129-136
• /
• 2010

In this work, PLLA/EGMA blends were prepared by melt blending of biodegradable Poly-L-lactic acid(PLLA) with Poly(ethylene-co-glycidyl methacrylate)(EGMA) and Engage as impact modifiers by twin screw extruder. Blend compositions of PLLA/Impact modifier blends were 100/0, 75/25, 50/50, 25/75 and 0/100, respectively. Also, Talc was added to 3 PLLA rich phases on PLLA/EGMA blends. The morphology, viscoelastic/mechanical properties were characterized by FESEM, DMA, UTM and Izod impact tester. DMA and Izod impact test data showed that storage modulus at room temperature with increasing EGMA and Engage contents decreased, and impact strength increased. However, storage modulus at room temperature increased by adding talc. From FESEM image, we observed that domain phase was well dispersed into matrix. Although the tensile strength and flexural modulus were decreased with increasing the content of EGMA and Engage in them, they could be supplemented by adding talc.

• Journal of Power System Engineering
• /
• v.21 no.1
• /
• pp.11-17
• /
• 2017

This study is about the mechanical properties of epoxy composite reinforced with nano $TiO_2$ particle. Tensile strength, fracture toughness, vicker's hardness and Izod Impact test were carried out to investigate the effect of particle size and content of $TiO_2$ on the mechanical properties of $TiO_2$/epoxy composites. The results showed that the strength of the $TiO_2$/epoxy composites were higher than that of the pure epoxy. The best improvement of tensile strength was achieved in case of the particle size was 21 nanometer and the content was 3 weight percent. However, the Izod Impact value and the Vicker's hardness of $TiO_2$/epoxy composites showed no clear tendency.

• Composites Research
• /
• v.12 no.6
• /
• pp.8-14
• /
• 1999

This research is focused on the investigation of impact strength and the microscopic observation of material behavior of glass fiber reinforced polypropylene in solid phase forming. The fiber weight per-centage of the composite materials was 20%, 30% and 40%. The solid-phase formed specimens were pre-strained to 10%,20%. and 30% strain levels. The forming temperatures of specimens were $100^{\circ}C$, $125^{\circ}C$ and $150^{\circ}C$. Izod impact test was performed with unnotched specimens. With increasing the glass fiber content ; the impact strength was increased.

• Applied Chemistry for Engineering
• /
• v.29 no.2
• /
• pp.168-175
• /
• 2018

In order to investigate the effect of the chemical treatment of bamboo fiber on physical properties of polypropylene (PP)/bamboo fiber (BF) composites, silane coupling agents such as ${\gamma}$-aminopropyltriethoxysilane (APS), ${\gamma}$-glycidoxypropyl-trimethoxysilane (GPS) and ${\gamma}$-mercaptopropyltrimethoxysilane (MRPS) were applied to BF and alkaline treated BF. Morphological properties of the chemically treated BF were confirmed by optical microscope and SEM measurements, and chemical structure changes were confirmed by FT-IR and EDS. TGA results showed that the thermal stability of silane treated BF increased. Based on the analysis of a universal testing machine and an Izod impact test, the flexural and impact properties of PP/silane treated BF composites showed higher values than those of PP/BF composites. The enhancement of interfacial adhesion properties of the PP/BF composite was checked from SEM images of the fracture of specimens after the tensile test.