• 한국전기전자재료학회논문지
• /
• 제36권5호
• /
• pp.482-487
• /
• 2023

A carbon-based hybrid resistor was fabricated using carbon nanotube (CNT) paste as an adhesive layer to establish electrically continuous ohmic contacts between CNT sheets and different CNT sheet or copper based metal alloy plates, and its electrical properties were evaluated. CNT sheets were fabricated using vacuum filtration with a CNT solution dispersed in isopropyl alcohol (IPA) solvent. The electrical characteristics of these carbon-based hybrid resistors were investigated. The CNT paste fulfilled the requirements for forming ohmic contacts between CNT sheets and metal alloy plates, which was attributed to the lowest work function difference and excellent wettability at the interface.

• 펄프종이기술
• /
• 제39권2호
• /
• pp.31-37
• /
• 2007

Lithography like off-set printing is processed using the repellent properties between water and oil, so all inks for off-printing must work with dampening solution(water). The dampening water may cause the emulsification of ink by the printing pressure in the printing nip. This study aimed to investigate the effect of emulsified inks on print mottle. The cyan ink was emulsified artificially with the different IPA(isopropyl alcohol) content in this study. We evaluated the print mottle by densitometer and image analysis method. The print mottle phenomenon was directly affected by IPA content. The emulsification of inks also had an influence on flow properties of inks and it increased ink transfer rate. It, however, caused low ink density. Moreover the emulsified inks were spreaded to around dots and cause the thinning density on the non-printing area like print mottle. The trial printing showed that the emulsified inks also cause scumming on the printing result with little mistake of adjusting dampening solution and mostly decreasing dot reproduction. We could, therefore, find out the obvious effect of emulsified inks on print mottle.

• 청정기술
• /
• 제14권3호
• /
• pp.184-192
• /
• 2008

불소계 화합물인 삼불화에탄올(2,2,2-trifluoroethanol, TFEA)와 수소화불화에테르(hydrofluoroether, HFE)는 성층권의 오존층을 파괴하지 않으며, 수소화불화탄소(hydrofluorocarbon, HFC) 및 수소화염화불화 탄소(hydrochlorofluorocarbon, HCFC)계 세정제에 비하여 지구온난화 영향력도 낮다. 특히, 인화점이 없는 HFE계 세정제는 낮은 인화점을 갖는 탄화수소계 세정제보다 취급에 안전하고 침투력이 우수하여 차세대 염화불화탄소(chlorofluorocarbon, CFC) 대체세정제로 주목받고 있다. 본 연구에서는 불소계 세정제인 TFEL HFE-7100, HFE-7200, HFE-476mec, HFE-449mec-f, AE-3000, AE-3100E와 실리콘계 세정제인 트리플 루로에톡시트리메틸실란(trifluoroetoxytrimethylsilane, TFES)와 헥사메틸디실라잔 (hexamethyldisilazane, HMDS)의 물성과 세정력을 오존파괴 물질인 CFC-113, 삼염화에탄(1,1,1-trichloroethane)와 유해물질인 이염화탄소(methylene chloride, MC) 등의 염소계 세정제, 그리고 현재 대체세정제로 많이 사용하고 있는 이소프로필알코올(isopropyl alcohol, IPA) 등과 비교 평가하였다. 그 결과 TFEA와 HFEs는 일반적으로 발생하는 다양한 오염물질들에 대하여 염소계 세정제에 비하여 낮은 세정능력을 보여주었지만, 불소를 함유한 불소계 오염물의 제거에는 우수한 세정력을 보였다. 그리고 실리콘계 세정제인 TFES와 HMDS도 실리콘계 오염물에 대한 세정력이 우수함을 보여주었다.

• 청정기술
• /
• 제16권3호
• /
• pp.172-181
• /
• 2010

CFC 세정제의 제3 세대 대체세정제로 평가되는 수소불화에테르(hydrofluoroether; HFE)는 불소분자를 함유하고 있어 표면장력이 낮고 습윤지수가 커서 미세입자제거와 불소계 오염물 제거에 우수하고 인화점이 없고 건조성이 뛰어난 물성을 가지고 있지만, 유기물의 용해력은 떨어져 유기 오염물 제거에는 효율적이지 못하다. 본 연구에서는 $C_5$계 HFE인 HFE-7100 [$CF_3CF_2CF_2CF_2OCH_3$]와 HFE-mec-f[$CF_3CHF=CF_2OCH_2CF_3$]에 유기물질의 용해력이 비교적으로 뛰어난 isopropyl alcohol (IPA), ethyleneglycol monoether (EG), propyleneglycol monoethylether (PM)를 인화점이 나타나지 않는 최대량을 각각 첨가하여 $C_5$계 HFE 기반의 배합세정제를 제조하여 물성과 여러 종류의 플럭스, 비수용성 절삭유, 불소계 오일에 대한 세정성 평가를 수행하였다. 실험 결과 $C_5$계 기반의 배합세정제는 단일 불소계 세정제의 여러 가지 물리적 성질의 장점을 가지는 것으로 나타났다. 그리고 $C_5$계 기반의 배합세정제는 첨가된 용제에 따라 약간의 차이는 있지만 대체적으로 플럭스, 비수용성 절삭유, 불소계 오일에 우수한 세정력을 나타내어 여러 산업세정 분야에 적용가능성을 보여주었다.

• 한국작물학회지
• /
• 제66권4호
• /
• pp.326-338
• /
• 2021

맥주보리 품종의 C-hordeins 분석을 위해 70% EtOH와 55% IPA가 추출용매로 이용되었으며, B-hordeins의 추출은 알코올성 용매에 1% DTT를 추가하여 수행되었다. D-hordeins은 보리 호데인 단백질 중 가장 분자량이 큰 단백질로 약산 혹은 약염기에서 용해가 이루어진다고 알려져 있으며, 본 연구에서는 pH 8.0의 약염기 용매가 추출용매로 이용되었다. 알코올성 용매 종류에 따른 C-hordeins의 구성과 양의 차이는 확인되지 않았으며 1% DTT가 첨가된 알코올성 용매에 B-hordeins과 C-hordeins이 모두 추출됨이 확인되었다. D-hordeins 추출 조건에서는 B-, C-, D-hordeins 이 모두 분석되었지만 B-hordeins의 머무름 시간은 1% DTT가 함유된 알코올 추출과 차이가 있었다. 국내 육성된 맥주보리 26품종들의 C-hordeins 분석을 통해 머무름 시간 16분에서 18분 사이의 피크 유사성을 가지고 7개의 그룹으로 분류할 수 있었다. 또한 맥주보리 육성 품종 중 사천6호와 두산29호, 진광보리와 제주보리, 호품과 다품보리를 제외한 20개 품종들은 마이너 피크들의 분석을 통해 품종의 구분이 가능하였다.

• Toxicological Research
• /
• 제32권4호
• /
• pp.337-343
• /
• 2016

We determined the toxicity of mixtures of ethyl acetate (EA), isopropyl alcohol (IPA), methyl ethyl ketone (MEK), toluene (TOL) and xylene (XYL) with half-maximal effective concentration ($EC_{50}$) values obtained using human hepatocytes cells. According to these data, quantitative property-activity relationships (QPAR) models were successfully proposed to predict the toxicity of mixtures by multiple linear regressions (MLR). The leave-one-out cross validation method was used to find the best subsets of descriptors in the learning methods. Significant differences in physico-chemical properties such as boiling point (BP), specific gravity (SG), Reid vapor pressure (rVP) and flash point (FP) were observed between the single substances and the mixtures. The $EC_{50}$ of the mixture of EA and IPA was significantly lower than that of contained TOL and XYL. The mixture toxicity was related to the mixing ratio of MEK, TOL and XYL (MLR equation $EC_{50}=3.3081-2.5018{\times}TOL-3.2595{\times}XYL-12.6596{\times}MEK{\times}XYL$), as well as to BP, SG, VP and FP (MLR equation $EC_{50}=1.3424+6.2250{\times}FP-7.1198{\times}SG{\times}FP-0.03013{\times}rVP{\times}FP$). These results suggest that QPAR-based models could accurately predict the toxicity of polar and nonpolar mixtures used in rotogravure printing industries.

• 한국재료학회지
• /
• 제23권2호
• /
• pp.116-122
• /
• 2013

For fabricating silicon solar cells with high conversion efficiency, texturing is one of the most effective techniques to increase short circuit current by enhancing light trapping. In this study, four different types of textures, large V-groove, large U-groove, small V-groove, and small U-groove, were prepared by a wet etching process. Silicon substrates with V-grooves were fabricated by an anisotropic etching process using a KOH solution mixed with isopropyl alcohol (IPA), and the size of the V-grooves was controlled by varying the concentration of IPA. The isotropic etching process following anisotropic etching resulted in U-grooves and the isotropic etching time was determined to obtain U-grooves with an opening angle of approximately $60^{\circ}$. The results indicated that U-grooves had a larger diffuse reflectance than V-grooves and the reflectances of small grooves was slightly higher than those of large grooves depending on the size of the grooves. Then amorphous Si:H thin film solar cells were fabricated on textured substrates to investigate the light trapping effect of textures with different shapes and sizes. Among the textures fabricated in this work, the solar cells on the substrate with small U-grooves had the largest short circuit current, 19.20 mA/$cm^2$. External quantum efficiency data also demonstrated that the small, U-shape textures are more effective for light trapping than large, V-shape textures.

• 한국기계가공학회지
• /
• 제10권5호
• /
• pp.131-136
• /
• 2011

Many researchers are recently studying about Electroactive polymer(EAP). But it has a physical limitation, because of property of material. Carbon nanotube(CNT) is known as the promising material which has excellent electro-mechanical characteristics and is mostly defect-free. It is expected that a successful synthesis of CNT and Nafion known as a primary material for IPMC would make a great improvement on its electro-mechanic feature. This study focuses on the method of synthesis of CNT with Nafion which improves electro-mechanical characteristic. To come up with mechanical dispersion with Nafion and Isopropyl Alcohol(IPA), we dispersed Single-walled carbon nanotubes(SWCNTs). For a uniformly layer of CNT, we used a spray gun on a hot plate by a simplified method. We fabricated a disperse SWCNT/Nafion composite uniformly. Through the use of the E-beam evaporator to form an uniform electrode layer, we consummated the IPMC actuator. This result shows improving 1.5 times mechanical properties about driving force in IPMC.

• 한국가시화정보학회지
• /
• 제10권3호
• /
• pp.21-24
• /
• 2012

Although the motion of the three-phase contact line on a solid substrate has been extensively studied thus far, the understanding of the dynamics of the contact line of liquid/liquid/gas phases is far from complete. Here we deposit a drop of isopropyl alcohol (IPA) on water and HFE-7100 whose free surfaces are exposed to air to observe the flow field around the contact line. By combining the shadowgraph and high-speed imaging techniques, we find that vortices are spontaneously generated at the contact line, which grow in size with time. The flow is attributed to the Marangoni stress that pulls a liquid of lower-surface tension toward a liquid surface having a higher surface tension. However, it is not still clear why the entrained lower-surface-tension liquid should whirl rapidly beneath the contact line. We also visualize the flow by the particle image velocimetry (PIV) to find out that the rotational velocity reaches the order of 1 mm/s near the free surface.

• 한국물환경학회지
• /
• 제31권1호
• /
• pp.42-48
• /
• 2015

This study focused on effective decomposition methods for low concentrated organic compounds from the reuse of industrial wastewater, and confirmed the possibility through photocatalyst media. Photocatalyst immobilized media was developed to carry on this experiment which confirmed the removal possibility of low concentrated organic compounds. Considering the stability and efficiency of photocatalyst immobilization, inorganic support, hollow bead, and $TiO_2$ nano powder were used. As a result of the removal experiment, the removal efficiencies of acetonitrile, ethanol, IPA(Isopropyl alcohol), methanol were above 75% after 15 minutes while those of acetone, acetaldehyde, urea were 10%, 45%, 20%, respectively after 60 minutes. If further studies were made to increase the surface area of the photocatalyst immobilized media, the efficiency of the removal of low concentrated organic compounds can be improved and this solution can also be used in an actual treatment process.