• Journal of Radiation Industry
• /
• v.6 no.2
• /
• pp.171-176
• /
• 2012

In this study, a crosslinked poly(styrene-butadiene-styrene) [SBS] block copolymers were prepared by using gamma ray irradiation method. The effects of various radiation doses on the degree of crosslinking, thermo property, and morphology of crosslinked SBS block copolymer were investigated. The degree of crosslinking of crosslinked SBS block copolymers were measured by gel-fraction and FT-IR. It was found that the degree of crosslinking of crosslinked SBS block copolymers increases with increase of the irradiation dose while the TGA result shows that the initial degradation temperature of irradiated SBS block copolymer was shifted to lower temperature with increasing irradiation dose. These results indicate that degradation reaction also occurs when SBS block copolymer is exposed to gamma ray irradiation for crosslinking reaction. The SAXS and FE-SEM results indicate that the phase separation of the styrene block and butadiene block was reduced with increasing irradiation dose.

• Nuclear Engineering and Technology
• /
• v.54 no.7
• /
• pp.2359-2366
• /
• 2022

Selecting graphite grades with superior irradiation characteristics is important task for designers of graphite moderation reactors. To provide reference information and data for graphite selection, the effects of irradiation on three fine-grained, iso-molded nuclear grade graphites, ETU-10, IG-110, and NBG-25, were compared based on irradiation-induced changes in volume, thermal conductivity, dynamic Young's modulus, and coefficient of thermal expansion. Data employed in this study were obtained from reported irradiation test results in the high flux isotope reactor (HFIR)(ORNL) (ETU-10, IG-110) and high flux reactor (HFR)(NRL) (IG-110, NBG-25). Comparisons were made based on the irradiation dose and irradiation temperature. Overall, the three grades showed similar irradiation-induced property change behaviors, which followed the historic data. More or less grade-sensitive behaviors were observed for the changes in volume and thermal conductivity, and, in contrast, grade-insensitive behaviors were observed for dynamic Young's modulus and coefficient of thermal expansion changes. The ETU-10 of the smallest grain size appeared to show a relatively smaller VC to IG-110 and NBG-25. Drastic decrease in the difference in thermal conductivity was observed for ETU-10 and IG-110 after irradiation. The similar irradiation-induced properties changing behaviors observed in this study especially in the DYM and CTE may be attributed to the assumed similar microstructures that evolved from the similar size coke particles and the same forming method.

• Proceedings of the KIEE Conference
• /
• 2009.04a
• /
• pp.183-185
• /
• 2009

In this thesis, output voltage, current and power of solar module were classified by irradiation and module temperature from data of overall operating characteristics collected for one year in order to manage efficient photovoltaic generation system and deliver maximum power. In addition, from these data, correlations between irradiation, module temperature of photovoltaic cell and amount of power given by photovoltaic cell was quantitatively examined to deduce optimization of the design and construction of photovoltaic generation system. The results of this thesis can be summarized as follows. As I-Y characteristics according to a temperature range of 10$\sim$50[], the area of I-V characteristics were increased with an increase in temperature. Since this area corresponds to the power, output power is thought to have increased with temperature.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.405-412
• /
• 2004

During the irradiation tests of material and fuel rod, all components of the cylindrical structure with multiple holes act like heat sources due to high gamma heat and fission heat. The objective of this study is to formulate the general solution for the temperature distribution to estimate the thermal integrity of structure during irradiation tests. For the temperature distribution analysis, the two-dimensional heat conduction theory is used. The unmerical analysis is performed by the commercial finite element analysis code, ANSYS 6.1. If the cylindrical structure with hole number would not exceed three holes, the analysis results and finite element results are good agreement together. For the structure with four holes, the discrepancy between FE results and analysis results of the structural temperature distribution is increased.

• Corrosion Science and Technology
• /
• v.7 no.2
• /
• pp.77-84
• /
• 2008

Based upon the good compatibility to neutron irradiation and high temperature water environment, austenitic stainless steels are widely used for core internal structural materials of light water reactors. But, recently, intergranular cracking was detected in the stainless steels for the core applications in some commercial PWR plants. Authors studied on the root cause of the intergranular cracking and developed the countermeasure including the alternative materials for these core applications. The intergranular cracking in these core applications are defined as an irradiation assisted mechanical cracking and irradiation assisted stress corrosion cracking. In this paper, the root cause of the intergranular cracking and its countermeasure are summarized and discussed.

• Korean Membrane Journal
• /
• v.7 no.1
• /
• pp.19-27
• /
• 2005

PP hollow fiber membrane was hydrophilized by EVOH dip coating followed by low temperature plasma treatment and UV irradiation. EVOH coating attained high water flux without any prewetting but its stability did not guaranteed at high water permeation rate. At high water permeation rate, water flux declined gradually due to swelling and delamination of the EVOH coating layer causing pore blocking effect. However, plasma treatment reduces the swelling, which suppress delamination of the EVOH coating layer from PP support result in relieving the flux decline. Also, UV irradiation helped the crosslinking of the EVOH coating layer to enhance the performance at low water permeation rate. FT-IR and ESCA analyses reveal that EVOH dip coating performed homogeneously through not only membrane surface but also matrix. Thermogram of EVOH film modified plasma treatment and W irradiation show that crosslinking density of EVOH layer increased. Chemical modification by plasma treatment and UV irradiation stabilized the hydrophilic coating layer to increase the critical flux of the submerged membrane.

• Preventive Nutrition and Food Science
• /
• v.2 no.1
• /
• pp.23-28
• /
• 1997

Physicohemical properties of corn starches isolated from non-glutinous and corn grains fol-lowing γ-irradiation up to 10kGy were investigated. Blue value, water binding capacity and swelling power decreased, while alkali number ad solubility increased by γ-irradiation , which was more pronounced in glu-tinous corn starch than in non-glutinous corn starch. The optical transmittance increased with an increment of heating temperature and applied irradiation doses. No significant difference was observed in Hunter's color value between both starches isolated from non- irradiated and irradiated and irradiated corn grains. Amylograph viscosities decreased remarkably as dose levels increased. The overall effects of γ-irradiation was more distinguished in glutinous starch than in non-glutinous starch.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.27 no.1
• /
• pp.63-68
• /
• 1998

Irradiation can be utilized to inhibit sprouting of onions and garlic. Thermoluminescence(TL) is a potential method to detect post-irradiation of onions and garlic because they are irradiated with soil or dusts on them, from which minerals can be isolated for TL analysis. This study was to determine whether TL can be applied for the detection of post-irradiation of onions and garlic. Onions and garlic produced in Korea were irradiated in the range of 0.01~0.6kGy. Minerals isolated from the samples using sodium polytrungstate solution were used for TL analysis. The onions and garlic irradiated at 0.15kGy or higher could be detected with little errors. Minimum dose for the 2nd glow could be applied since the dose for the 2nd glow did not affect the results. The TL intensities of the temperature ranges of 229~295$^{\circ}C$ and 229~361$^{\circ}C$ and the maximum intensity provided more accurate information for the determination of the post-irradiation of onions and garlic.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.220-220
• /
• 2009

In case of favourable irradiation conditions, the ratio of irradiation to the total irradiation went up and then the irradiation increased in the area with high angle of inclination. The study showed that on a clear day with the irradiation of more than $800[W/m^2]$, the pattern of alternating current power change in the fixed system was similar with that in the single-axis tracker. On the contrary, in case of unfavourable irradiation conditions, the ratio of diffuse irradiation to the total irradiation went up and then the horizontal irradiation increased. In the demo system, the fixed system, the single-axis tracker and the dual-axis tracker all had low generation power and similar generation pattern with each other. The study showed the generation power varied with the irradiation in the fixed system, while in the single-axis tracker and the dual-axis tracker, the amount of the generation power variation was much more than the irradiation variation. The demo system was operated from 11:00 AM to 2:00 PM for generating power, during which time, 46[%] to 56[%] of the total generation power was produced. In this study. the generation power was increased by 147[%] in the fixed system, by 136[%] in the single-axis tracker, and by 164[%] in the dual-axis tracker, and the pattern of generation power was similar with the generation power variation in the situation where the irradiation increased by 140[%] in the spring with plenty of insolation. The alternating current power was more sensitive to variation of the irradiation than to that of the surface temperature of a module. The variation of the irradiation had a more positive effect on the generation power than the type of array.

• Nuclear Engineering and Technology
• /
• v.52 no.6
• /
• pp.1213-1221
• /
• 2020

Chromium-nickel alloy 42XNM (XHM-1, Bochvalloy) is considered as a promising material for future generations of nuclear reactors, primarily as a material for the fuel elements shells in the development of accident tolerant fuel. However, as with most nickel-based alloys, 42ХNМ is characterized by a sharp decrease in plastic properties in the temperature range of (500-900)℃. This effect is enhanced by neutron irradiation. Preliminary tests of ring samples of 42XNM alloy (after irradiation as a part of the VVER-1000 control system) in the temperature range of ductility failure showed that the standard technique for processing tensile diagrams does not allow to evaluate the plastic properties correctly at low strains. Therefore, in this work, the alternative method for testing ring samples from materials with low plastic characteristics was developed. It was shown that the minimum value of the permanent strain of the irradiated 42XNM alloy in the temperature range of (500-1100)℃, determined by the alternative method, was ~1.6% at 750 ℃.