• Membrane and Water Treatment
• /
• v.7 no.4
• /
• pp.277-296
• /
• 2016

The aim of this research was to investigate the ability of nanofiltration (NF) and ultrafiltration (UF) membranes as a filtration unit for groundwater treatment for drinking water resources. Commercial membranes denoted as TS40, TFC-SR3 and GHSP were used to study the performance based on rejections and fluxes. The investigation has been conducted using natural groundwater obtained from a deep tube well with initial concentration of iron (Fe) and manganese (Mn) at 7.15 mg/L and 0.87 mg/L, respectively. Experimental results showed that NF membranes exhibited higher fluxes than UF membrane with pure water permeability at 4.68, 3.99 and $3.15L.m^{-2}.h^{-1}.bar^{-1}$, respectively. For metal rejection, these membranes have performed higher removal on Fe with TS40, TFC-SR3 and GHSP membranes having more than 82%, 92% and 86% respectively. Whereas, removal on Mn only achieved up to 60%, 80% and 30%, for TS40, TFC-SR3 and GHSP membranes respectively. In order to achieve drinking water standard, the membranes were efficient in removing Fe ion at 1 and 2 bar in contrast with Mn ion at 4 and 5 bar. Higher rejection of Fe and Mn were achieved when pH of feed solution was increased to more than 7 as TFC-SR3 membrane was negatively charged in basic solution. This effect could be attributed to the electrostatic effect interaction between membrane material and rejected ions. In conclusion, this study proved that NF membrane especially the TFC-SR3 membrane successfully treated local groundwater sources for public drinking water supply in line with the WHO standard.

• 보존과학연구
• /
• s.26
• /
• pp.41-56
• /
• 2005

A set of horse bit from the Eonnam-ri site consists of three parts, pyo , ham , andinsu , and each part takes a shape of a piece of bar. According to current typological study, the pyo is S type, the insu is two-braided line type, and the outer rim of the ham is double rim type, respectively. According to X-ray test, inlaid design seems to have been decorated on the whole surface of the iron bit, originally. However, inlaid pattern partially remained. While the part of bit stopper is designed with flame pattern, the part of rein joint is designed with cloud pattern. According to XRF and XGT analysis of inlaid material, the content of silver is not more than 50%. The line inlay method making grooves on the surface of iron, then in laying a silver thread into them, and grinding the surface in a direction was adoptedin the manufacture of the iron bit.

• Journal of Korean Elementary Science Education
• /
• v.26 no.4
• /
• pp.440-448
• /
• 2007

The purpose of this study is to examine elementary students' conceptions of magnetic fields around various magnets by drawing tasks. A total of 105 elementary students from the 3rd and 6th grade levels were asked to draw how iron filings would arrange around magnets. We classified their drawings of magnetic field lines with some criteria to identify conceptions of magnetic forces and checked them through interviewing about their representative drawing. Through analyzing drawings, we discovered that 40% of elementary students drew the correct arrangement of iron filings around a bar magnet. In the case of two bar magnets in opposite directions, 33% of them drew correct patterns of iron dust and around two magnets in the same direction only 20% did well. Only 2.9% and 7.6% of students presented the correct drawings of magnetic fields near a disc and a horseshoe magnet. While 3rd grade students were supposed to be poor in drawings of magnetic fields around a loose and a dense coil which was not learned about, only 31% and 23% of 6th grade students who have just studied electromagnetism properly drew patterns of iron dust. This shows that only one quarter of students understood the magnetic filed lines even after instruction of electromagnetism. Many of 6th grade students learned a solenoid becomes just as a permanent magnet, but very few of them correctly drew a magnetic field line could distinguish between the iron dust around a loose and dense coil. After interviewing students, it is found that students consider magnetic forces to be existed only in parts of magnet because many of them drew magnetic field line of a specific areas around magnets. Students had misconceptions that magnetic forces exist only on the poles not in the middle around a horseshoe magnet. Also the disc-shape magnet made students to reveal various types of misconceptions: N- and S-poles are mixed in a whole magnet and right part of a disc-shape magnet is N-pole, left part is S-pole. Students who had not studied magnetic fields of around a magnet and electromagnets could not draw the correct patterns of iron dust suggest that it is indispensable for students to teach how patterns of iron filings would represent a visual image of magnetic fields in order to understand magnetic fields.

• Journal of Conservation Science
• /
• v.35 no.6
• /
• pp.631-640
• /
• 2019

The purpose of this study was to compare analytical results of sand iron bars reproduced by the traditional iron-making method through a destructive analysis and a non-destructive analysis. For these studies, we produced two types of samples. One was sample(SI-A), a part of the sand iron bar for destructive analysis. The other was SI-B(9 ㎠) for non-destructive analysis. A metallurgical microscope and scanning electron microscope were used for the destructive analysis, and neutron imaging analysis with the Hokkaido University Neutron Source (HUNS) at Hokkaido University, Japan, was used for the non-destructive analysis. The results obtained by destructive analysis showed that there was ferrite and pearlite of fine crystallite size, and some of these showed Widmanstätten ferrite microstructure grown within the pearlite and coarse ferrite at the edge of the specimen. The results from the neutron imaging analysis showed that there was also ferrite and pearlite with 3 ㎛ α-Fe of BCC structure. Based on these results, neutron imaging analysis is capable of identifying material characteristics without destroying the object and obtaining optimal research results when applying it to objects of cultural heritage.

• Journal of Korea Foundry Society
• /
• v.8 no.3
• /
• pp.310-321
• /
• 1988

This study is aimed to investigate the effects of the multi-phase(ferrite-bainite-martensite) on the strengthening and toughening in ductile cast iron. All the specimen were austenitized at eutectoid transformation temperature range(${\alpha}+{\gamma}$) for 1hr and austempered at $300^{\circ}C$ and $400^{\circ}C$ for various holding time, and then quenched in iced water for multi - phase (${\alpha}-B-M$). When the volume fraction of martensite is below 15%, excellent maximum fracture load can be obtained due to strengthening by the fine martensite, but, with increasing of volume fraction over 15%, it was decreased drastically. The martensite size became finer and the shape of it changed from bar to spherical type with increasing of austempering holding time. The higher the austenitizing temperature is, the more preferential is the formation of austenite phase around the graphite nodules improving strength and toughness of austempered ductile cast iron.

• Proceedings of the KIEE Conference
• /
• 1997.07a
• /
• pp.41-43
• /
• 1997

This paper represents the comparison of harmonic loss characteristics of the inverter-driven 3-phase squirrel cage induction motor with slit and U-iron bridge slots of rotor. Two-dimensional time-stepped finite element method is used for electromagenetic field analysis. And spectrums of bar current, phase current, and torque are compared in each case.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.12 no.6
• /
• pp.180-192
• /
• 2008

The purpose of this research is to evaluate the structural performance of mortar-filled ductile cast iron sleeve splice developed for SD500 high-strength reinforcing bar under cyclic loading. The test variables adopted in this study are the development length of bar, compressive strength of mortar, bar size, sleeve types and others. In this research, it is showed that the mortar-filled sleeve splice for SD500 high-strength bar satisfied the structural performance required in ACI, AIJ code as well as domestic code. Also the results of experimental research presented in this paper provided basic engineering data for developing a reasonable design method of mortar-filled sleeve splice for SD500 high-strength reinforcing bar.

• Journal of Korea Foundry Society
• /
• v.10 no.4
• /
• pp.299-308
• /
• 1990

Ductile cast iron has a good ductility and ductility and toughness than those of gray cast iron, because the shape of graphite is spheroidal. It has been reported that the strengthening and toughening of the ductile cast iron was resulted from the good modification of various matrix structures obtained by the heat treatment or addition of alloying elements. This study aims to investigate the effect of various special heat treatment(Cyclic Heat Treatment, Intermediate Heat Treatment, Step Quenching), austempering and alloying element(Ni) on the strength and toughness of ductile cast iron. The results obtained from this study are summarized as follows. 1) With addition of Ni, the amount of pearlite or bainite were increased and the morphologies of pearlite or bainite became finer by special heat treatments. 2) As the Ni added and not added ductile cast iron were treated by austenitizing at $900^{\circ}C$ and $840^{\circ}C$, in the latter the austenite was mostly formed in the vicinity of eutectic cell boundary, but in the former on the whole matrix. 3) In cyclic heat treatment, the volume fraction of pearlite was increased and the shape of pearlite was fined with increase of the number of cycle. 4) The shape of pearlite was mostly bar type in the intermediate heat treatment, but spheroidal type in step quenching. 5) The mechanical properties of ductile cast iron containing 1.5%Ni austempered at $400^{\circ}C$ for 25min. after austenitizing at $900^{\circ}C$ for 15min. were a good value of hardness 105(HRB), impact energy 12.5(kg.m), tensile strength 112($kg/mm^2$) and elongation 6.8(%).

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.4
• /
• pp.287-293
• /
• 2002

The unexpected failure of the induction motor makes the downtime of production, and the cost of the process cessation enormous. To reduce the downtime and increase the reliability of the motor, the vibration measurements for the fault detection have been used previously. Recently motor current signature analysis(MCSA) has been adapted for the fault detection and diagnosis of the motors. MCSA provides a powerful analysis tool for detecting the presence of mechanical and electrical faults in both the motor and driven equipment. In this paper, the fault severity of the rotor bar has been derived in terms of the resistance change which is calculated from the equivalent circuit model. Results show that the fault of the rotor can be easily detected and the measured value of the resistance change is verified by the detected fault from on-site tests using MCSA for the induction motors in an iron foundry.

• Journal of Magnetics
• /
• v.21 no.2
• /
• pp.209-214
• /
• 2016

This paper analyzes the magnetic property according to the machined shape of steel material with non-oriented silicon steel (50PN470/50A470), that is most commonly used in the design of electrical equipment. Toward this end, specimens were produced and divided into Bar-Specimen (Epstein Frame Tester) and Ring-Specimen (Toroidal Ring Tester). The characteristics of the electrical Silicon steel were measured using the instruments solely dedicated to measuring each specimen. The core loss of the Bar-Specimen, which is commonly used, was found to be less than that of the Ring-Specimen. This is a very important design factor in achieving the objectives of improving the product efficiency and predicting the performance of electrical equipment. It serves as a critical point of view in order to reduce the error between design value and product value. A comparative analysis was conducted regarding various characteristics (Hysteresis, B-H characteristic, Iron loss, Minor loop, Coercive force, Residual magnetic flux density, etc.) of the electrical silicon steel considered in the design of the electrical equipment according to the specimen.