• Resources Recycling
• /
• v.31 no.6
• /
• pp.25-35
• /
• 2022

The adsorption/desorption behavior and separation conditions of vanadium and tungsten ions were investigated using a gel-type anion-exchange resin. In the adsorption experiment with the initial acidity of the solution, the adsorption rate of vanadium was remarkably low in strong acids and bases. Additionally, the adsorption rate of tungsten was low in a strong base. An increase in the reaction temperature increased the adsorption reaction rate and maximum adsorption. The effect of tungsten on the maximum adsorption was minimal. The adsorption isotherms of vanadium and tungsten on the ion-exchange resin were suitable for the Langmuir adsorption isotherms of both the ions. For tungsten, the adsorption isotherms of vanadium and tungsten were polyoxometalate. Both ion-exchange resins were simulated using similar quadratic reaction rate models. Vanadium was desorbed in the aqueous solutions of HCl or NaOH, the desorption characteristics of vanadium and tungsten depended on the desorption solution, and tungsten was desorbed in the aqueous solution of NaOH. It was possible to separate the two ions using the desorption process. The desorption reaction reached equilibrium within 30 min, and more than 90% recovery was possible.

• Korean Chemical Engineering Research
• /
• v.45 no.2
• /
• pp.160-165
• /
• 2007

The synthesis and the characterization of Low Silica X (LSX) zeolite for nitrogen adsorption have been studied. The performance of LSX zeolite for nitrogen adsorption was compared to that of the commercial zeolite. The $Na_2O/(Na_2O+K_2O)$ ratio in the gel and the crystallization time were fixed as the synthetic factor. The LSX zeolite was formed at the $Na_2O/(Na_2O+K_2O)$ ratio of 0.75. The formation of LSX zeolite was confirmed by XRD and SEM. The Si/Al ratio was investigated by using XRF and FT-IR. The synthesized LSX zeolite showed a lower Si/Al ratio than the NaY and NaX zeolites although they have a same faujasite structure. The Si/Al ratio of the LSX zeolite converged close to 1. 1A (Li, Na, K) and 2A (Mg, Ca, Ba) group elements were ion-exchanged to the LSX zeolite. As the charge density of cation rises, the amount of nitrogen adsorbed increased. $Li^+$ ion-exchanged LSX zeolite showed the highest nitrogen adsorption weight. When the Li/Al ratio was over 0.65, nitrogen adsorption increased remarkably. $Li^+$ ions located on the supercage (site III, III') in the LSX zeolite played a role as nitrogen adsorption sites. When the $Ca^{2+}$ ions were added to the LiLSX zeolite by ion-exchange method, the performance for nitrogen adsorption increased more. The performance for the nitrogen adsorption was the highest at the Ca/Al ratio of 0.26. Nitrogen adsorption capacity of LiCaLSX (Ca/Al=0.26) zeolite was superior to the commercial NaX zeolite.

• Macromolecular Research
• /
• v.12 no.6
• /
• pp.573-580
• /
• 2004

To prepare chitosan-based polymeric amphiphiles that can form nanosized core-shell structures (nanopar­ticles) in aqueous milieu, chitosan oligosaccharides (COSs) were modified chemically with hydrophobic cholesterol groups. The physicochemical properties of the hydrophobized COSs (COSCs) were investigated by using dynamic light scattering and fluorescence spectroscopy. The feasibility of applying the COSCs to biomedical applications was investigated by introducing them into a gene delivery system. The COSCs formed nanosized self-aggregates in aqueous environments. Furthermore, the physicochemical properties of the COSC nanoparticles were closely related to the molecular weights of the COSs and the number of hydrophobic groups per COS chain. The critical aggregation concentration values decreased upon increasing the hydrophobicity of the COSCs. The COSCs effi­ciently condensed plasmid DNA into nanosized ion-complexes, in contrast to the effect of the unmodified COSs. An investigation of gene condensation, performed using a gel retardation assay, revealed that $COS6(M_n=6,040 Da)$ containing $5\%$ of cholesteryl chloroformate (COS6C5) formed a stable DNA complex at a COS6C5/DNA weight ratio of 2. In contrast, COS6, the unmodified COS, failed to form a stable COS/DNA complex even at an elevated weight ratio of 8. Furthermore, the COS6C5/DNA complex enhanced the in vitro transfection efficiency on Human embryonic kidney 293 cells by over 100 and 3 times those of COS6 and poly(L-lysine), respectively. Therefore, hydrophobized chitosan oligosaccharide can be considered as an efficient gene carrier for gene delivery systems.

• Korean Journal of Materials Research
• /
• v.22 no.2
• /
• pp.66-70
• /
• 2012

Ti-Ni alloys are widely used in numerous biomedical applications (e.g., orthodontics, cardiovascular science, orthopaedics) due to their distinctive thermomechanical and mechanical properties, such as the shape memory effect, superelasticity and low elastic modulus. In order to increase the biocompatibility of Ti-Ni alloys, many surface modification techniques, such as the sol-gel technique, plasma immersion ion implantation (PIII), laser surface melting, plasma spraying, and chemical vapor deposition, have been employed. In this study, a Ti-49.5Ni (at%) alloy was electrochemically etched in 1M $H_2SO_4$+ X (1.5, 2.0, 2.5) wt% HF electrolytes to modify the surface morphology. The morphology, element distribution, crystal structure, roughness and energy of the surface were investigated by scanning electron microscopy (SEM), energy-dispersive Xray spectrometry (EDS), X-ray diffractometry (XRD), atomic force microscopy (AFM) and contact angle analysis. Micro-sized pores were formed on the Ti-49.5Ni (at%) alloy surface by electrochemical etching with 1M $H_2SO_4$+ X (1.5, 2.0, 2.5) wt% HF. The volume fractions of the pores were increased by increasing the concentration of the HF electrolytes. Depending on the HF concentration, different pore sizes, heights, surface roughness levels, and surface energy levels were obtained. To investigate the osteoblast adhesion of the electrochemically etched Ti-49.5Ni (at%) alloy, a MTT test was performed. The degree of osteoblast adhesion was increased at a high concentration of HF-treated surface structures.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.402.1-402.1
• /
• 2016

The performance of solid oxide fuel cells (SOFCs) is directly related to the electrocatalytic activity of composite electrodes in which triple phase boundaries (TPBs) of metallic catalyst, oxygen ion conducting support, and gas should be three-dimensionally maximized. The distribution morphology of catalytic nanoparticle dispersed on external surfaces is of key importance for maximized TPBs. Herein in situ grown nickel nanoparticle onto the surface of fluorite oxide is demonstrated employing gadolium-nickel co-doped ceria ($Gd0.2-xNixCe0.8O2-{\delta}$, GNDC) by reductive annealing. GNDC powders were synthesized via a Pechini-type sol-gel process while maximum doping ratio of Ni into the cerium oxide was defined by X-ray diffraction. Subsequently, NiO-GNDC composite were screen printed on the both sides of yttrium-stabilized zirconia (YSZ) pellet to fabricate the symmetrical half cells. Electrochemical impedance spectroscopy (EIS) showed that the polarization resistance was decreased when it was compared to conventional Ni-GDC anode and this effect became greater at lower temperature. Ex situ microstructural analysis using scanning electron microscopy after the reductive annealing exhibited the exsolution of Ni nanoparticles on the fluorite phases. The influence of Ni contents in GNDC on polarization characteristics of anodes were examined by EIS under H2/H2O atmosphere. Finally, the addition of optimized GNDC into the anode functional layer (AFL) dramatically enhanced cell performance of anode-supported coin cells.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.237.1-237.1
• /
• 2016

Electrical properties of graphene-based field effect transistors (G-FETs) can be degraded in ambient conditions owing to physisorbed oxygen or water molecules on the graphene surface. Passivation technique is one of a fascinating strategy for fabrication of G-FETs, which allows to sustain electrical properties of graphene in the long term without disrupting its inherent properties: transparency, flexibility and thinness. Ironically, despite its importance in producing high performance graphene devices, this method has been much less studied compared to patterning or device fabrication processes. Here we report a novel surface passivation method by using atomically thin self-assembled alkane layers such as C18- NH2, C18-Br and C36 to prevent unintentional doping effects that can suppress the degradation of electrical properties. In each passivated device, we observe a shift in charge neutral point to near zero gate voltage and it maintains the device performance for 1 year. In addition, the fabricated PG-FETs on a plastic substrate with ion-gel gate dielectrics exhibit not only mechanical flexibility but also long-term stability in ambient conditions. Therefore, we believe that these highly transparent and ultra-thin passivation layers can become a promising candidate in a wide range of graphene based electronic applications.

• Applied Chemistry for Engineering
• /
• v.10 no.5
• /
• pp.666-671
• /
• 1999

In this work, sulfonated poly(phenylene sulfide) (SPPS) was prepared by demethylation with aqueous NaOH solution after poly[methyl[4-(phenylthio)phenyl]sulfonium trifluoromethanesulfonate](PPST) was sulfonated with fumic sulfonic acid(10% $SO_{3}-H_{2}SO_{4}$). PPST soluble in organic solvents was synthesiszed by self-condensation polymerization of methyl-(phenylthio)phenyl sulfoxide(MPPSO). SPPS showed IR bands of asymmetric O=S=O stretching at $1200cm^{-1}$ and S-O stretching at $621cm^{-1}$ from $-SO_{3}H$ group. From the result, it could be known that sulfonic acid groups were introduced to poly(phenylene sulfide). when PPST was sulfonated for 12hr at $150^{\circ}C$, 1.48 sulfonic acid groups were introduced per repeat unit. The weight average molecular weight(Mw) of PPST and SPPS determined by high temperature GPC were 118323 and 131204, respectively. The SPPS exhibited adsorption capacity of ammonia gas $9.67mmol\;NH_{3}/g$ and it was much higher than that of active carbon or silica gel.

• Journal of Microbiology and Biotechnology
• /
• v.4 no.2
• /
• pp.113-118
• /
• 1994

A bacterial strain NS-83 isolated from soil was able to produce an extracellular thermostable protease. The strain was identified as Pseudomonas aeruginosa based on its morphological and physiological characteristics. A thermostable protease from this strain has been purified to homogeneity as judged by SDS-PAGE and isoelectric focusing. The purification procedures included hydrophobic interaction, ion exchange, and gel filtration chromatography. The $M_r$ and the pl of the enzyme were 32,000 and 5.9, respectively. The optimal pH at 55$^{\circ}C$ and the optimal temperature at pH 7.0 were 8.0 and 60$^{\circ}C$, respectively. The D-values of the enzyme at 60, 65, and 70$^{\circ}C$ were 22, 2.1, and 0.75 hrs, respectively. The enzyme activity was significantly inhibited in the presence of 1 mM o-phenanthroline or EDTA, suggesting that the enzyme is metalloprotease. The $K_m$, and $V_{max}$ for Hammarsten casein were found to be 3.2 mg/ml and 0.918 unit/ml, respectively. These enzymatic properties were similar to those of elastase produced from P. aeruginosa IFO 3455, but the enzyme was clearly different from the reported elastase, in respect to $Ca^{++}$ effects on enzyme-thermostability. This property, together with amino acid composition analysis, confirmed that the enzyme differs from the known P. aeruginosa elastase.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2009.11a
• /
• pp.39.1-39.1
• /
• 2009

NiTi alloy is widely used innumerous biomedical applications (orthodontics, cardiovascular, orthopaedics, etc.) for its distinctive thermomechanical and mechanical properties such as shape memory effect, super elasticity, low elastic modulus and high damping capacity. However, NiTi alloy is still a controversial biomaterial because of its high Ni content which can trigger the risk of allergy and adverse reactions when Ni ion releases into the human body. In order to improve the corrosion resistance of the TiNi alloy and suppress the release of Ni ions, many surface modification techniques have been employed in previous literature such as thermal oxidation, laser surface treatment, sol-gel method, anodic oxidation and electrochemical methods. In this paper, the NiTi was electrochemically etched in various electrolytes to modify surface. The microstructure, element distribution, phase composition and roughness of the surface were investigatedby scanning electron microscopy (SEM), energy-dispersive X-ray spectrometry(EDS), X-ray diffractometry (XRD) and atomic force microscopy (AFM). Systematic controlling of nano and submicron surface features was achieved by altered density of hydro fluidic acid in etchant solution. Nanoscale surface topography, such as, pore density, pore width, pore height, surface roughness and surface tension were extensively analyzed as systematical variables.Importantly, bone forming cell, osteoblast adhesion was increased in high density of hydro fluidic treated surface structures, i.e., in greater nanoscale surface roughness and in high surface areas through increasing pore densities.All results delineate the importance of surface topography parameter (pores) inNiTi to increase the biocompatibility of NiTi in identical chemistry which is crucial factor for determining biomaterials.

• Microbiology and Biotechnology Letters
• /
• v.37 no.2
• /
• pp.147-152
• /
• 2009

A xylanase was purified from the culture supernatant of Bacillus sp. A-6 by using ultrafiltration and ion exchange chromatography on the column of SP-Sepharose using 5 mM acetate buffer, pH 5.0. The xylanase was eluted from the column at the concentration less than 0.05 M NaCl. The eluted xylanase was shown to be a single protein band in SDS-PAGE. Zymogram analysis indicated that the protein band in SDS-PAGE had the enzyme activity to hydrolyze oat spelt xylan. The molecular weights of the xylanase were 15,000 based on SDS-PAGE and 14,100 based on gel filtration chromatography. Thin layer chromatography showed that the xylanase hydrolyzed oat spelt xylan into xylobiose and high-molecular-weight xylooligosaccharides. The relative activities of the heated xylanase decreased to 80% at $40^{\circ}C$ after 7 hr and less than 40% at $60^{\circ}C$ after 1 hr.