• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.1258-1261
• /
• 2004

ACSR전력선의 송전용량 증가를 위해 개발된 증용량저이도 송전선인 STACBUAW(Super Thermal-resistant Aluminum alloy Conductors, aluminum-clad Invar-Reinforced)전선은 초내열 Al도체 및 인바강선의 사용으로 비교적 고온에서의 안정적 운전이 가능하다. 그러나 고온 환경에서 장시간 노출된 STACIR/AW전선의 안정적 관리를 위해서는, 열화 된 STACIR/AW 전선의 인장강도, 각 구성소재의 탄성 계수, 비틀림 계수 둥과 같은 기계적 물성이 장기 운전 모의를 위해 설정된 열화온도, 열화시간 등에 대해 종합적으로 평가될 필요가 있다. 또한 크립 등과 같이 고온응력 부하상태에서의 변형거동과 탄성계수 및 선 팽창계수의 온도의존성 등은 전선의 이도관리와 예측을 위해서도 명확히 규명되어야할 중요한 관리 인자이다. 그러나 현재까지는 이들에 대해 수행한 어떠한 연구결과들도 보고 되어 있지 않은 실정이다. 본 연구에서는 STACIR/AW $410mm^2$ 송전선을 장시간 운전의 모의를 위해 가속열화 시키고 가속열화에 따른 STACIR/AW전선 및 그 구성소재의 강도, 비틀림 특성의 변화를 조사하여 장시간 운전에 따른 STACIR/AW전선의 안정성을 평가하여 보고하고자 하였다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.1053-1055
• /
• 2002

Recently CRT is getting large-sized, Flatness and High Fine Pitched in the meantime the raw material for shadow mask is in rapid progress of thinness, Low Thermal Expansion and high strength.Until now we have used AK(Aluminum Killed) & Invar(Fe-Ni alloy) materials for main raw material of shadow mask component. However recently Nb and Co addition and Nb+Co addition, which has advantage of Low Thermal Expansion and High Strength. has been developed as well as applying in mass production as CRT's trend has become more flat and fine pitch. Among of them, Co addition has been mass production as forming type (Flat CRT) with the beneficial effect of low thermal expansion & high strength for the first time. Since then Nb+Co addition has been used in mass production by the request of much higher strength of shadow mask component. In case of Nb addition, It's thermal expansion coefficient is a little lower than normal Invar and a little higher than Co addition, meanwhile Its Mechanical property is almost similar to Co Addition. The used samples of this experiment are 36%Ni + Fe, 32%Ni + 5%Co + Fe, 32%Ni + 5%Co + 0.3%Nb + Fe, 32%Ni + 0.3%Nb + Fe with heat treatment temperature of 600$^{\circ}C$, 650$^{\circ}C$, 700$^{\circ}C$, 750$^{\circ}C$, 800$^{\circ}C$, 850$^{\circ}C$, 900$^{\circ}C$ respectively under the condition of 15min holding time. After heat treatment, we have observed the change of mechanical property with addition of small elements through mechanical property investigation and metal structure observation as well as transition of thermal expansion coefficient by measuring of thermal expansion coefficient at 850$^{\circ}C$. In conclusion, 5%Co addition indicates that its thermal expansion coefficient is very similar under the condition of at 850$^{\circ}C$ for 15min 's heat treatment. From the experimental result it is suggested that Co addition is mostly suitable for Doming property and Nb addition is mostly suitable for Drop property.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.05b
• /
• pp.69-73
• /
• 2005

ACSR전력선의 송전용량 증가를 위해 개발된 중용량저이도 송전선인 STACIR/AW(Super Thermal-resistant Aluminum alloy Conductors, aluminum-clad Invar-Reinforced)전선은 초내열 Al도체 및 인바강선의 사용으로 비교적 고온에서의 안정적 운전이 가능하다. 그러나 고온 환경에서 장시간 노출된 STAClR/AW전선의 안정적 관리를 위해서는, 열화 된 STACIR/AW 전선의 인장강도, 각 구성소재의 탄성계수, 비틀림 계수 등과 같은 기계적 물성이 장기 운전 모의를 위해 선정된 열화온도, 열화시간 등에 대해 종합적으로 평가될 필요가 있다. 또한 크립 등과 같이 고온응력 부하상태에서의 변형거동과 탄성계수 및 선팽창계수의 온도의존성 등은 전선의 이도관리와 예측을 위해서도 명확히 규명되어야할 중요한 관리 인자이다. 그러나 현재까지는 이들에 대해 수행한 어떠한 연구결과들도 보고 되어 있지 않은 실정이다. 본 연구에서는 STACIR/AW $410mm^2$ 송전선을 장시간 운전의 모의를 위해 가속열화 시키고 가속열화에 따른 STACIR/AW 전선 및 그 구성소재의 강도, 비틀림 특성의 변화를 조사하여 장시간 운전에 따른 STACIR/AW전선의 안정성을 평가하여 보고하고자 하였다.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.355-356
• /
• 2009

The change of thermal expansion and mechanical behaviors by cold working has been investigated in Fe-29%Ni-17%Co low thermal expansion Kovar alloy. Fe-29%Ni-17%Co alloy was cold rolled gradually and prepared to plates having reduction ratio of 0%, 20%, 40%, 60%, and 80%. Annealing effect on the properties was also studied. Thermal expansion was measured from $25^{\circ}C$ to $600^{\circ}C$ with a heating rate of $5^{\circ}C$/min by using vacuum differential dilatometer. It was found that thermal expansion coefficient ($\alpha_{30{\sim}400}$) slightly decreased (reduction ration of 20%) and then remarkably increased (above reduction ration of 40%) with increasing reduction ratio of cold rolling. Thermal expansion coefficient ($\alpha_{30{\sim}400}$) was sharply decreased after annealing heat-treatment. Yield and tensile strengths were continuously increased and elongation was decreased by cold roiling. Microstructural observation and X-ray diffraction analysis results showed that the $\alpha$ phase significantly increased as the reduction ratio increased. The slight decrease of thermal expansion coefficient bellow reduction ration of 20% could be explained by the destroying short-range ordering and the decreasing of grain size. The significant increase of thermal expansion coefficient with cold rolling mainly attributed to the appearance of $\alpha$ phase. The correlation between the microstructural cause and invar phenomena for the low thermal expansion behavior was also discussed.

• Journal of the Korean Vacuum Society
• /
• v.20 no.6
• /
• pp.436-441
• /
• 2011

Metal coating with several nanometer thickness was applied on the carbon nanotubes (CNTs) in order to improve electron emission characteristics and emission reliability for the potential applications in the area of various electron sources and displays. CNTs were grown on the 2-nm thick Invar (52% Fe, 42% Ni, 6% Co alloy)-catalized Si substrate by using plasma-enhanced chemical vapor deposition at $450^{\circ}C$. In order to reduce the spatial density of densely packed CNTs, as-grown CNTs were partly etched back by $N_2$ plasma and subsequently coated with 5~150 nm thick Ti by a sputtering method. 5 nm thick Ti-coated CNTs produced four times higher emission current density at the electric field of 6 V/${\mu}m$ and much lower emission current fluctuation, compared with the as-grown CNTs. These improved emission properties are mainly due to not only the work function of Ti (4.3 eV) lower than that of pristine CNTs (5 eV), but also lower contact resistance and better adhesion between CNT emitters and substrate accomplished by Ti coating.

• Clean Technology
• /
• v.13 no.4
• /
• pp.274-280
• /
• 2007

A liquid-liquid solvent extraction process was developed in this study to recover Fe and Ni from heavily concentrated aqueous ferric chloride solution, in an effort to substitute the conventional iron reduction method. Solvent composition and extraction conditions were first developed from the laboratory experiments, and the pilot system was designed and built for commercialization. Stage numbers for extraction and stripping were determined from pilot plant runs, and other operation data were obtained for mass production.

• Journal of the Society of Naval Architects of Korea
• /
• v.48 no.3
• /
• pp.200-206
• /
• 2011

The mechanical properties of the most widely used cryogenic materials, i.e. austenitic stainless steel (ASS), aluminum alloy and invar steel, strongly depend on temperatures and strain rates. These phenomena show very complicated non-linear behaviors and cannot be expressed by general constitutive equation. In this study, an unified constitutive equation was proposed to represent the effect of temperature and strain rate on the materials. The proposed constitutive equation has been based on Tomita/Iwamoto and Bodner/Partom model for the expression of 2nd hardening due to martensite phase transformation of ASS. To simulate ductile fracture, modified Bodner/Chan damage model was additionally applied to the model and the model validity was verified by comparison of experimental and simulation results.

• Journal of the Korean Magnetics Society
• /
• v.12 no.6
• /
• pp.218-223
• /
• 2002

We investigated the magnetic properties of High Flux-type $Ni_{x}Fe_{100-x}$(x=40∼50, wt.％) permalloy powders and dust cores. The powder was prepared by conventional gas atomization in mass production scale. At the composition of $Ni_{x}Fe_{55}$, saturation magnetization was maximum. In case of lower Ni content than X=45, the $M_{s}$, decreased largely with the decrease in Ni content, which is due to the invar effect. The permeability of compressed powder cores increased with the decrease in Ni content, which was considered to be due to the decrease in the magnetostriction. In addition, the dust core with Ni=45％ showed the lowest core loss because of the increase in electrical resistivity leading to the low eddy current loss. From the better frequency dependence of permeability, larger Q value and superior DC bias characteristics of Ni=45％ than those of Ni=50％ core, it was confirmed that the 45％Ni-55％Fe powder alloy was better material for the dust core than commercial High Flux core materials.