• 한국전자통신학회논문지
• /
• 제7권6호
• /
• pp.1429-1435
• /
• 2012

태양광 시스템이나 연료전지 시스템 그리고 전기자동차에 많이 사용되는 DC-DC 컨버터는 부스트 컨버터이다. 이러한 부스트 컨버터를 병렬로 연결하고 위상차를 두고 동작하여 입출력 전류리플을 줄이는 인터리브드 부스트 컨버터가 최근에 많이 사용되고 있다. 이 회로는 입출력 전류 리플이 작기 때문에 입출력 커패시터의 크기를 줄일 수 있다. 따라서 기존의 전해 커패시터를 신뢰성이 우수한 필름 커패시터로 교체할 수 있고 이는 전체 시스템의 수명 및 신뢰성을 향상시킬 수 있다. 본 논문에서는 다단 인터리브드 부스트 컨버터에 사용되는 출력 커패시터의 전류리플 수식을 유도하고 듀티에 따른 특성을 알아본다. 이를 확인하기 위해서 PSIM 툴을 이용하여 계산된 값과 비교를 할 것이다.

• 전기학회논문지
• /
• 제59권1호
• /
• pp.88-95
• /
• 2010

In this paper, the variation of phase current and input current ripple of interleaved boost converter at DCM for fuel cell applications are theoretically analyzed. Also, based on the detailed analysis, numerical formula of input current ripple expressed in rising and falling slope magnitude, D, and $D_A$ is proposed. In order to verify proposed formulas, simulation and experimental results are compared with theoretical data and validity of proposed theory is established.

• 전기학회논문지P
• /
• 제65권4호
• /
• pp.303-308
• /
• 2016

A light-emitting diode (LED) has been increasingly applied to various industrial fields and general lightings because of its high efficiency, low power consumption, environment-friendly characteristic and long lifetime. To drive this LED lighting, various types of power converters have been applied. Also, power factor correction (PFC) techniques play an important role in the power supply technology. In this paper, design and control of a DCM interleaved boost PFC converter is discussed. The proposed converter can reduce current ripples at input and output side by cancelling an each phase of inductor currents. Since the IC does not require the auxiliary winding of inductor for current detection, simple PFC circuit is achieved. Therefore, it contributes to increase efficiency and downsize the whole system volume, cost. Also, the performance of the proposed system is demonstrated through experiments.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2006년도 전력전자학술대회 논문집
• /
• pp.19-21
• /
• 2006

In contrast with DC source, Fell cell has non linear characteristics that has lange voltage fluctuation due to load variation, and slow dynamic characteristics. when the loads are increase, the ripples of input and output voltage, also power densities, of inductor, capacitor, and switching devices, are bulky. This paper presents Interleaved boost converter using Fuel cell stacks, proposed converter has merits to promote power densities without increasing loss. Because each converter has same switching frequency and constant phase difference. In this paper, Interleaved boost converter was design for 1[kW], it's validity was proved by simulation and experiments.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.785-787
• /
• 2005

This paper addresses the small-signal analysis of the multi-phase interleaved boost converter with the coupled inductors operated in the continuous inductor current mode. The generalized and analytical expressions for the transfer functions of interest are derived for various inductor couplings. The dynamic characteristics are analyzed according to the inductor couplings and verified experimentally. The proposed frequency models will be very useful to design the dynamic controllers of the multi-phase interleaved boost converters.

• Journal of Electrical Engineering and Technology
• /
• 제5권2호
• /
• pp.319-328
• /
• 2010

In this paper, an optimal selection methodology for the number of phases will be proposed for an interleaved boost converter (IBC). Also, the analysis of the input current ripple according to CCM and DCM is carried out. The proposed design methodology will be theoretically analyzed, and its validity verified by simulation as well as with experimental results. Moreover, a comparison of cost and efficiency based on a 600W laboratory prototype using the Ballard NEXA 1.2kW PEMFC system is demonstrated.

• Journal of Power Electronics
• /
• 제15권4호
• /
• pp.1035-1046
• /
• 2015

This study presents a practical implementation of a multi-mode two-phase interleaved boost converter for fuel cell electric vehicle application. The main operating modes, which include two continuous conducting modes and four discontinuous conducting modes, are discussed. The boundaries and transitions among these modes are analyzed with consideration of the inductor parasitic resistance. The safe operational area is analyzed through a comparison of the different operating modes. The output voltage and power characteristics with open-loop or closed-loop operation are also discussed. Key performance parameters, including the DC voltage gain, input ripple current, output ripple voltage, and switch stresses, are presented and supported by simulation and experimental results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2012년도 전력전자학술대회 논문집
• /
• pp.195-196
• /
• 2012

In recent years, in an effort to improve the efficiency and the power density of the front-end power factor correction(PFC), the interleaving of multiple converter is employed. The conventional interleaved continuous conduction mode(CCM) boost PFC converter requires input and output voltage sensing and three current sensing to obtain current balancing between modules. In this paper, the interleaved CCM PFC converter based on modulated carrier control is proposed. With the proposed method, two phase interleaved PFC can be realized simply without line voltage sensing resistor and can achieve current balancing without additional current sensing resistor on common return path. The simulation studies are carried out to verify the effectiveness of the proposed control scheme.

• Journal of Power Electronics
• /
• 제17권1호
• /
• pp.41-55
• /
• 2017

This study proposes a novel zero voltage transition (ZVT) pulse width modulation (PWM) DC-DC interleaved boost converter with an active snubber cell. All the semiconductor devices in the converter turn on and off with soft switching to reduce the switching power losses and improve the overall efficiency. Through the interleaved approach, the current stresses of the main devices and the ripple of the output voltage and input current are reduced. The main switches turn on with ZVT and turn off with zero voltage switching (ZVS). The auxiliary switch turns on with zero current switching (ZCS) and turns off with ZVS. In addition, the snubber cell does not create additional current or voltage stress on the main switches and main diodes. The proposed converter can smoothly achieve soft switching characteristics even under light load conditions. The theoretical analysis and operating stages of the proposed converter are made for the D > 50% and D < 50% modes. Finally, a prototype of the proposed converter is implemented, and the experimental results are given in detail for 500 W and 50 kHz. The overall efficiency of the proposed converter reached 95.5% at nominal output power.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권7호
• /
• pp.343-351
• /
• 2003

In this paper, interleaved boost converter is applied as a first-stage converter in switch mode power supply. The first-stage converter plays a role to improve power factor. Interleaved Boost Power Factor Corrector(IBPFC) can reduce input current ripple as a single voltage control loop only without inner current loop, because input current is divided each 50% by two switching devices. Each converter cell is also operated in discontinuous current mode and inductor current of each converter is discontinuous. Total input current which is composed by each converter cell is continuous current. Thus, IBPFC is able to improve input current ripple. IBPFC operating in discontinuous current mode can be classified as six modes from switching state and be carried out state space averaging small signal modeling. A control transfer function is obtained according to the modeling. Not only steady-state characteristics but also dynamic characteristics is considered. Single voltage control loop is also constructed by the control transfer function. From experimental result, improvement of power factor and input current ripple are verified.