• Progress in Superconductivity and Cryogenics
• /
• v.14 no.4
• /
• pp.50-53
• /
• 2012

This paper describes experimental study on GM-type pulse tube refrigerator (PTR). In a PTR, the pulse tube is only filled with working gas and there exists secondary flow due to a large temperature difference between cold-end and warm-end. The stability of secondary flow is affected by orientation of cold-head and thus, the cooling performance is deteriorated by gas mixing due to secondary flow. In this study, a single stage GM-type pulse tube refrigerator is fabricated and tested. The cooing performance of the fabricated PTR is measured as varying cold-head orientation angle and the results are used as reference data. Then, we divided interior space of pulse tube into three segments, and fixed the various size of screen mesh at interface of each segment to suppress the performance degradation due to secondary flow. For various configuration of pulse tube, no-load test and heat load test are carried out with the fixed experimental condition of charging pressure, operating frequency and orifice valve turns. From experimental results, the fine screen mesh shows the effective suppression of performance degradation for the large orientation angle, but the use of screen mesh cause the loss of cooling capacity rather than the case of no insertion into pulse tube. It should be compromised whether the use of screen mesh in consideration of the installation limitation of a GM-type pulse tube refrigerator.

• Journal of Korean Institute of Fire Investigation
• /
• v.10 no.1
• /
• pp.59-75
• /
• 2007

The causes of the fire casualties were the heat burns, contacted by flame, before the period of industrialization. According to the economic has been developed drastically since 1990, residing space has been become bigger and sophistication and interior finishing materials have been diversified. Therefore, the suffocation casualties, caused by inspiration of toxic combustion gases, have been more increased than the flame casualties in recently. Also, the arson casualties have been increasing with the increasing of insurance crime to take the Insurance money. According to National Emergency Management Agency announcement, 31,778 fires was occurred nationwide in 2006 and the total casualties were 2,180 occurred. 446 persons were died among them. Because the exact investigation of fire, occurred the death, is very especially important that civil and criminal cases will be happened. Therefore, we studied about the cause of fire, the place of origin, and the group of casualties age on the axies of fires, which were occurred recently. And the identification method of fire casualties, the human behavior characteristic, the flame casualties and the suffocation casualties at fire scene.

• Journal of the Korea Furniture Society
• /
• v.17 no.4
• /
• pp.1-13
• /
• 2006

This study attempted to identify the characteristics of chair design from furniture company, $K{\ddot{a}}llemo$, the furniture manufacturer in Sweden manufacturing mostly the limited edition of art furniture on the basis of the unique management philosophy. There are 12 artists manufactured chairs for $K{\ddot{a}}llemo$. Of them, this study selected 4 artists-Sigurdur Gustafsson, John Kandell, Komplot Design, Mats Theselius-who designed at least more than three chairs. Total 25 chairs were analyzed; 6 from Sigurdur Gustafsson, 8 from John Kandell, 3 from Komplot Design and 8 from Mats Theselius. The chair structure was divided into three parts, seat, back and structure and analyzed by material, color, type of legs and finishing. The following results were derived from the study. First, $K{\ddot{a}}llemo$ secured the regular customers who want to possess the chairs as the artistic works by continuing the small quantity mass-production system insisting that the maximum quantity of production is 360 pieces and the minimum quantity is 33 pieces. Second, the sufficient time and cost were invested in the initial phase of design. This approach seems to be deviated from the traditional business system that has to create the revenue at a glance, but ultimately induces the commercial success by exponentially increasing the revenue through the creation of various product lines. Third, $K{\ddot{a}}llemo$ provides the space that the artists who work for $K{\ddot{a}}llemo$ can sufficiently enjoy the mental composure and luxury required for the designers by strictly selecting the artists and providing the best environment for enabling the creative activities that look like the pure art area. This study enables the further analysis and research on other collections of $K{\ddot{a}}llemo$ that mass-produces the chairs on the basis of the unique philosophy in the world as well as in Sweden using more various kinds of analysis frameworks.

• Journal of The Korea Institute of Healthcare Architecture
• /
• v.23 no.1
• /
• pp.15-24
• /
• 2017

Purpose: Korea is expected to enter an aged society in 2018 and then a super-aged society in early 2025. The country's aging is progressing faster than any other country in the world. However, the foundation of the elderly friendly industry is weak, and measures at the government level are urgently needed. Especially, housing problems of the elderly are one of the most urgent measures to be taken. Korea does not have the minimum residential area standard for the elderly, and the current general minimum residential area standard is based on the survey of the housing situation without scientific evidence. Therefore, both standards need to be revised as soon as possible based on scientific evidence. Methods: The minimum residential area standard has been calculated following Karl H. E. Kroemer's Min or Max design also being called as-single cut and dual cut theory- as the maximum population value and minimum population value theory of Ernest J. McCormick. Therefore there is a need for a formula made using a few key factors, such as corresponding dimension, practical dimension, clearance, spare dimension, integrated dimension. These elements can be defined and used as formulas to calculate minimum residential area standards. Results: Assuming the results of the spatial variability in this study showed that it is possible to raise the standard of living in a terms of sustainable minimum size for the young, old and all residents. Implications: The government should set a minimum residential area standard with scientific grounds and set up a policy improving the life of people who live in an needy residential environment.

• Fire Science and Engineering
• /
• v.18 no.1
• /
• pp.42-48
• /
• 2004

The deterministic modeling techniques like Zone model and Field model are mainly used for thermal distribution and smoke flow at fire case in multi use facilities. While Zone model analyse fire simulation by dividing spaces by 2 section, the Field model dividing many cells. However, the difficultly follows to prove efficiency between the two models when it applys. Therefore new modeling development is required which in closes to real situation by verify number algorithm and related data for fire modeling. The paper analyses the efficiency of two different fire modeling at interior spaces of multiplex cinema theater. It is found that the zone model for average distribution and the field model for detail space phenomenon are relevant to apply. Also, Filed model is useful to the result that fire analysis and position of detector and review for smoke control system.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.10a
• /
• pp.357-359
• /
• 2010

In monocular images that are used to determine the depth of the vanishing point, the buildings, roads and buildings, such as outdoor video or hallway with room inside for the interior structure, such as the vanishing point in the video is a very strong depth cue. Depth map using the vanishing point in the three-dimensional space, the two-dimensional imaging is used to restore the structure. But if there is a vanishing point vanishing point in the video also depends on the location of the relative depth of different ways to express that need. In this paper we present images of a vanishing point with respect to the improved depth-map was created. Proposed an area where the loss of seven points and areas defined as areas along the proposed direction of different depth.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.10
• /
• pp.44-49
• /
• 2021

Seats in autonomous vehicles must be able to rotate to fully utilize the interior space. Generally, ultra-high strength steel is used for the rotation module because it should have high strength and high rigidity. In addition, the rotating parts are difficult to form because they have complex shapes. In this study, the upper plate of the rotating module, whose complex shape makes it difficult to form, was formed by applying the hot stamping method. The drawing method and the form-drawing method, which are generally used to form components of complex shapes, were compared. We showed that the form-drawing method increased the degree of freedom of the material flow to improve the formability, thus enabling the forming of the plate. In addition, the die and blank shapes were found to be important factors in determining the success of the hot stamping. The validity of the analysis results was confirmed through forming analysis and experiments.

• Journal of the Korea Convergence Society
• /
• v.12 no.9
• /
• pp.137-151
• /
• 2021

Revitalized alley-type urban commercial streets have recently received a lot of attention as a preferred place for people. The purpose of this study is to present implications in the planning and design methods for the making of alley-type urban commercial street. For that, theoretical review and case analysis were conducted on the street spatial characteristics of 'Jeonridan-gil' and 'Mangmidan-gil' in Busan, about site overview, street spatial composition, building use, streetscape and street furniture. The implications through the study are as follows. (1) Street environment should be created to improve the pedestrian space and environment. (2) The existing main use and the newly introduced use need to be coexisted. (3) The identity of the street must be maintained through adaptive reuse, etc. (4) The voluntary formation of the private sector and the planned making of the public need to be cooperated.

• Journal of Fashion Business
• /
• v.23 no.1
• /
• pp.49-63
• /
• 2019

The purpose of this study is to examine the characteristics of modular design observed in Korean traditional clothing. Modular design, which is one of the noticeable characteristics of modern fashion design emerged in the 20th century. This study analyzed the Korean traditional culture to investigate the characteristics that show similarities to the modular system in design. A traditional Korean house is composed of small structures called 'chae'. A traditional Korean building is composed of a basic unit space called 'kan', and the rooms are divided and recombined. Korean traditional interior design shows furniture, bedding and art works that could be used, folded then stored. Korean cuisine is served in combination with small dishes. Korean letters are combined in square shaped form to make writing and printing easy. Korean traditional clothing has a way of washing where clothing are disassembled, washed and then re-stitched. The pattern pieces are made to be rectangular shaped so that the fabric pieces can be kept in shape during washing. The rectangular shaped pattern pieces can be replaced and reused after washing. Tops and bottoms could be interchanged for color-coordination, because the shapes of the clothing were standardized. These features exhibit modular system in Korean traditional clothing design. Modular system design has common characteristics which have basic modules, pursue practical purpose, have interchangeability adapted to circumstances, and could be disassembled and re-combined. Korean traditional clothing illustrates different ways of practicing modular system, but has some common features to contemporary modular fashion design.

• Journal of the Architectural Institute of Korea Planning & Design
• /
• v.34 no.11
• /
• pp.75-84
• /
• 2018

This study analyzed users' acceptance and intention to use in addition to needs and preferences of smart home technologies, and identified the differences in technology preference and acceptance by different factors. The subjects were residents in the 40s and 60s residing in the Seoul or suburbs of Seoul, and questionnaires were conducted in the 40s while interviews with questionnaires were conducted in the 60s. A total of 105 questionnaires were used as data, and frequency, mean, crossover, independent sample t test, one-way ANOVA and multiple regression analysis were performaed using SPSS23. The results of this study are as follows. First, hypertension, hyperlipidemia and hypercholesterolemia were the most common diseases among respondents and if there was no discomfort, they would like to continue living in the homes of the current residence. Therefore, the direction of smart home development should support the daily living and health care so that residents can live a healthy life for a long time in their living space. Second, the technologies that residents most need were a control technology of residential environments and a monitoring technology of residents' health and physiological changes. The most preferred sensor types are motion sensors and speech recognition while video cameras have a very low preference. Third, technology anxiety was the most significant factor influencing intention to accept smart home technology. The greater the technology anxiety is, the weaker the acceptance of technology. Fourth, when applying smart residential technology in homes, various resident characteristics should be considered. Age and technology intimacy were the most influential variables, and accordingly there were differences in technology preference and acceptance. Therefore, a user-friendly smart home plan should be done in the consideration of the results.