• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.399-407
• /
• 2010

SC-FDMA system uses DFT-spreading method for reducing the PAPR of OFDM signal, which improves the power efficiency. Block type pilot is used in SC-FDMA system. However, there are ICI due to the inevitable phase noise and frequency offset that can be generated from the Doppler frequency and inaccuracy between the transceiver oscillators. This ICI definitely degrades the BER performance. To overcome this problem and estimate the channel efficiently, we like to propose ICI compensation algorithm for the SC-FDMA system with comb type pilot. SLM method is additionally included for the PAPR reduction when pilot is assigned in comb type. Finally, it is confirmed that the ICI due to the phase noise and frequency offset is efficiently compensated by the suggested algorithm.

• Progress in Superconductivity and Cryogenics
• /
• v.15 no.2
• /
• pp.20-23
• /
• 2013

For sensitive measurements of micro-Tesla nuclear magnetic resonance (${\mu}T$-NMR) signal, a low-noise superconducting quantum interference device (SQUID) system is needed. We have fabricated a liquid He dewar for an SQUID having a large diameter for the pickup coil. The initial test of the SQUID system showed much higher low-frequency magnetic noise caused by the thermal magnetic noise of the aluminum plates used for the vapor-cooled thermal shield material. The frequency dependence of the noise spectrum showed that the noise increases with the decrease of frequency. This behavior could be explained from a two-layer model; one generating the thermal noise and the other one shielding the thermal noise by eddy-current shielding. And the eddy-current shielding effect is strongly dependent on the frequency through the skin-depth. To minimize the loop size for the fluctuating thermal noise current, we changed the thermal shield material into insulated thin Cu mesh. The magnetic noise of the SQUID system became flat down to 0.1 Hz with a white noise of 0.3 $fT/{\surd}Hz$, including the other noise contributions such as SQUID electronics and magnetically shielded room, etc, which is acceptable for low-noise ${\mu}T$-NMR experiments.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.8
• /
• pp.1165-1171
• /
• 2010

The OFDM system has better characteristics in transmission rate, power efficiency, bandwidth efficiency, impulse-noise immunity, and narrow band interference immunity etc. in comparison with other conventional systems. However, high PAPR of an OFDM signals causes some serious non-linear processing of RF amplifier. And performance of the communication system gets worse. Therefore, various methods reducing PAPR of an OFDM skills such as the clipping method, block coding method, and phase rotation method etc. have been researched. In this paper, we propose a high-speed adaptive PTS method which eliminates high PAPR. And we compare the proposed method with other conventional methods. The proposed method has decreased quantity of calculation compare with an adaptive PTS method. Of course, The more its calculation amount is decreased, the more its BER characteristic is not better than an adaptive PTS method. However, keeping up satisfactory BER performance, we highly improved calculation amount of a PTS method.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.1
• /
• pp.27-38
• /
• 2002

The effects of Reynolds number on the non-nulling calibrations of a cone-type ave-type probe in low-speed flows have been investigated at Reynolds numbers of 2.04$\times$10$^3$, 4.09$\times$10$^3$and 6.13$\times$10$^3$. The calibration is conducted at the pitch and yaw angles in ranges between -35 degrees and 35 degrees with an angle interval of 5 degrees. In addition to the calibration coefficients, reduced pitch and yaw angles, static and total pressures, and velocity magnitude are obtained through a typical non-nulling reduction procedure. The result shows that each calibration coefficient, in general, is a function of both the pitch and yaw angles, so that the pre-existing calibration data in a nulling mode are not enough in accounting far the full non-nulling calibration characteristics. Due to interference of the probe stem, the calibration coefficient are more sensitive to Reynolds number at positive pitch angles than at negative ones. The calibration data reduced in this study may serve as a guide line in the estimation of uncertainty intervals resulted from the Reynolds number effects at low Reynolds numbers.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.3
• /
• pp.115-124
• /
• 2002

This paper presents an active auxiliary edge-resonant DC link snubber with a ringing surge damper and a three-phase voltage source type zero voltage soft-switching inverter with the resonat snubber treated here for the AC servo motor driver applications. The operation of the active auxiliary edge-resonant DC link snubber circuit with PWM voltage is described, together with the practical design method to select its circuit parameters. The three-phase voltage source type soft-switching inverter with a single edge-resonant DC link snubber treated here is evaluated and discussed for the small-scale permanent magnet (PM) type-AC servo motor driver from an experimental point of view. In addition to these, the AC motor stator current and its motor speed response for the proposed three-phase soft-switching inverter employing Intelligent Power Module(IPM) based on IGBTS are compared with those of the conventional three-phase hard-switching inverter using IPM. The practical effectiveness of the three-phase soft-switching inverter-fed permanent magnet type AC motor speed tracking servo driver is proven on the basis of the common mode current in a novel type three-phase soft-switching inverter-fed AC motor side and the conductive noise on the mains terminal interface voltage as compared with those of the conventional three-phase hard-switching inverter-fed permanent magnet type AC servo motor driver for the speed tracking applications.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.39 no.spc1
• /
• pp.142-150
• /
• 2006

We examined the effect of predation by observing the changes in macrobenthic communities in a tidal flat at Seonjae, Korea, following the exclusion of large predators such as birds, fishes and crustaceans using protective screens. We conducted two interference experiments in the field from April to November 2004: (1) Experiment 1 was conducted at a mid-tidal flat in the western part of Seonjae-do, Incheon, Korea, (2) Experiment 2 was set up at a low tidal flat in the eastern part of Seonjae-do. predator exclusion showed different effects in the two experiments. Both the number of species and density were reduced by 20% in Experiment 1. Whereas in Experiment 2, they increased by up to 13% and 69%, respectively. In Experiment 1, a high density of brachyuran crabs observed in the treatment may have caused the difference in community composition between the treatment and the control, and this probably resulted from active predation of macrofauna (e.g., small crabs) under protection from megafaunal predators such as birds and fishes. However, in Experiment 2, as typically observed in other predator exclusion experiments, a lower density of benthic predators and the subsequent reduction of over predation probably resulted in a more diverse and abundant benthic community in the treatment. We confirmed that predation was a contributing factor in the formation of the macrobenthic community. We also demonstrated relationships that exist among different trophic groups (large predators, macrobenthic predators and prey) and what effects and responses occur in each component of the tidal flats.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.3
• /
• pp.38-43
• /
• 2008

The hydroforming technology has been spreaded dramatically in automotive industry last 10 years. Itmay cause many advantages to automotive applications in terms of better structural integrity of the parts, lower cost from fewer part count, material saving, weight reduction, lower springback, improved strength and durability and design flexibility. In this study, the whole process of rear sub-frame parts development by tube hydroforming using steel material having tensile strength of 440MPa grade is presented. At the part design stage, it requires feasibility study and process design aided by CAE (Computer Aided Design) to confirm hydroformability in details. Effects of parameters such as internal pressure, axial feeding and geometry shape in automotive rear sub-frame by hydroforming process were carefully investigated. Overall possibility of hydroformable sub-frame parts could be examined by cross sectional analyses. Moreover, it is essential to ensure the formability of tube material on every forming step such as pre-bending, preforming and hydroforming. In addition, all the components of prototyping tool are designed and interference with press is examined from the point of geometry and thinning.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.17 no.6
• /
• pp.558-571
• /
• 1992

In this paper, we propose an improved method of state exploration called the extended circular exploration (ECE) for the efficiency of state exploration and the reduction of explosively growing state. The ECE does not need to explore all the reachable global states, and It can be applied to JV($\boxDr$$\geq$ 2) -party protocol with alternative routes, i.e., it is applicable to the protocol In which adaptiverouting mechanism can be performed. The ECE eliminates a restriction of topology of the conventional circular exploration(CE) by exploring only those global states which are reachable, provided that the participant processes of any group of transitions proceed at the same speed, and that they can be formed as a cycle. Thus the state space explored if not exhaustive. The algorithm presented can detect deadlock error and unspecified reception error It requires storage space and /or execution time much less than those of the conventional perturbation(CP) . It might be used for a solution of the N-process collision and the interference mechanism.

• Proceedings of the Microbiological Society of Korea Conference
• /
• 2008.05a
• /
• pp.62-64
• /
• 2008

A major hurdle to the development of RNA interference as therapy for HIV infection is the delivery of siRNA to T lymphocytes which are difficult cells to transfect even in vitro. We have employed a single chain antibody to the pan T cell surface antigen CD7 was conjugated to an oligo-9-arginine peptide (scFvCD7-9R) for T cell-specific siRNA delivery in NOD/SCIDIL2${\gamma}$-/- mice reconstituted with human peripheral blood lymphocytes (Hu-PBL). Using a novel delivery, we first show that scFvCD7-9R efficiently delivered CD4 siRNA into human T cells in vitro. In vivo administration to Hu-PBL mice resulted in reduced levels of surface CD4 expression on T cells. Mice infected with HIV-1 and treated on a weekly basis with scFvCD7-9R-siRNA complexes targeting a combination of viral genes and the host coreceptor molecule CCR5 successfully maintained CD4/CD3 T cell ratios up to 4 weeks after infection in contrast to control mice that displayed a marked reduction in CD4 T cell numbers. p24 antigen levels were undetectable in 3 of the 4 protected mice. scFvCD7-9R/antiviral siRNA treatment also helped maintain CD4 T cell numbers with reduced plasma viral loads in Hu-PBL mice reconstituted with PBMC from donors seropositive for HIV, indicating that this method can contain viral replication even in established HIV infections. Our results show that scFvCD7-9R could be further developed as a potential therapeutic for HIV-1 infection.

• Journal of Internet Computing and Services
• /
• v.16 no.2
• /
• pp.7-17
• /
• 2015

To provide scalability, wireless sensor network has cluster-based architecture. Wireless sensor network can be implemented based on the IEEE 802.15.4 which is exploited in 2.4GHz ISM frequency band. Since this frequency band is used for various data communication, network status of wireless sensor networks frequently changes according to wireless environment. Thus, wireless channel selection to avoid reduction of transmission efficiency is required. This paper estimates network status using the information that a cluster-head collects in a cluster. Through objective function with throughput, RSSI level and reliability as input parameters, this paper proposes proper wireless channel selection. Simulation results show that the proposed method maintains transmission efficiency even though network status changes.