• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.494-497
• /
• 2002

Conducted electromagnetic interference (EMI) from switch mode power supplies (SMPS) has become a major problem due to the proliferation of these devices employing dc-dc converters using standard pulse width modulation (PWM). In this paper, we proposed the sigma-delta modulation $({\sum}{\Delta}M)$ as an alternative switching technique to reduce the conducted EMI in SMPS. A comparative investigation on conducted EMI generated by PWM and ${\sum}{\Delta}M$ techniques are experimentally performed on a 300W Boost converter.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.498-501
• /
• 2002

In the conventional PWM converter, high-frequency switching techniques was used for high-density of energy, but occurred a lot of problems such as switching losses, switching voltage/current stresses, EMI(Electromgnetic Interference) and so on. To overcome these problems, various soft switching techniques have been presented. However these techniques are focused on reducing switching losses and voltage/current stresses . The simulation and experimental results are shown that the active clamp ZVS flyback converter with the proposed RPWM(Random Pulse Width Modulation) technique reduces the conducted noise.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.793-797
• /
• 2003

Switching PFC converters are widely used not only to comply the power quality specification but also for maximum efficiency. However switching PFC converters generate serious electromagnetic interference (EMI). In this paper to solve this problem, we applied the APW(Anti Phase Winding) and RPWM(Ran-dom PWM) technique to PFC boost converter and obtained satisfactory results. Simulation and experimental results show the improved harmonic and reduced EMI effect in air-conditioner system.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.5-9
• /
• 1998

In the high speed rail system, the distortion of the voltage and the current waveform of the input power line increases the power loss and make a several electro-magnetic problems such as EMI or the interference of the communication line. In this paper, the control scheme of the PWM converter to make a good power factor and to regulated the output voltage as well as to reduce the harmonic component of the input current is proposed. Also a control schem of the PWM converter in the parallel operation to reduce the harmonics of the input current is proposed

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.625-629
• /
• 1998

So far a single-axis controlled repulsive type magnetic bearing system have been designed and fabricated in our laboratory employing the repulsive forces operating between the stator and rotor permanent magnet for levitation. The radial axis is uncontrolled passive one. The higher speed of operation is limited due to the vibration along the uncontrolled axis and the increase of control current due to eddy current interference. This paper will discuss a detailed modeling of the repulsive type magnetic bearing system for five axis control including the eddy current effect and the method of reduction of eddy current effect. Simulation results using Matlab will be presented.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12B
• /
• pp.1741-1746
• /
• 2001

This paper proposes the OFDM system that uses circularly polarized waves for improving the system performance. The circular polarization has the characteristic that it cannot receive the waves which are reflected by odd times. Using this characteristic, a modified OFDM system that uses the cross-handed circular polarization(XCP-OFDM) is newly proposed. By using the characteristic of circular polarization, it is clearly seen that the system performance of XCP-OFDM can be improved to a great extent. This is due to a reduction of the interferences caused by reflected waves and inter-channel interference. Both theoretical analysis and system simulation results are described.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.211-214
• /
• 2002

In this paper, We have investigated the EMI (electro magnetic interference) characteristics of electrodeless fluorescent lamp ballast as a ground connection and have measured various waveforms, which can be expressed the disturbance voltages and radiated electromagnetic disturbances. induced the measuring instrument and found that effect of ground connection is the one of the important elements on EMI reduction.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.11
• /
• pp.435-438
• /
• 1997

One of the main techniques or diagnosing heart disease is by examining the electrocardiogram(ECG). Many studies on detecting the QRS complex, P, and T waves have been performed because meaningful information is contained in these parameters. However, the earlier detecting techniques can not effectively extract those parameters from the ECG that is severely contaminated by noise source such 60Hz powerline interference, motion artifact and baseline drift. in this paper, we performed the extracting parameters from and recovering the ECG signal using wavelet transform that has recently been applying to various fields.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.955-956
• /
• 2014

Active noise control is noise reduction method by generate anti-phase control signal for destructive interference of through control speaker. purpose of this paper is create a virtual control source at a using the DBAP(Distance Based Amplitude Panning) algorithm which is one of the three-dimensional sound reproduction method, and verified through the experimentally for noise control method through the virtual control source. We compared active noise method by using one control speaker with active noise control method by using DBAP algorithm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.4
• /
• pp.336-342
• /
• 2003

In this paper, a new differential detector is introduced, in which a solar cell is used to reduce the low frequency interference from environmental optical noise. The solar cell also supplies electrical power to the detector circuit using the optical noise power. The DC voltage from the solar cell is used as a power supply to the detector, and the AC voltage is used to reduce the optical noise in a photodiode with the differential detection method. The signal to noise ratio was improved by about 20 dB.