• Journal of Electrochemical Science and Technology
• /
• v.6 no.4
• /
• pp.116-120
• /
• 2015

Lithium diffusivity of fluorine-free and -doped tin-nickel (Sn-Ni) film model electrodes with improved interfacial (solid electrolyte interphase (SEI)) stability has been determined, utilizing variable rate cyclic voltammetry (CV). The method for interfacial stabilization comprises fluorine-doping on the electrode together with the use of electrolyte including fluorinated ethylene carbonate (FEC) solvent and trimethyl phosphite additive. It is found that lithium diffusivity of Sn is largely dependent on the fluorine-doping on the Sn-Ni electrode and interfacial stability. Lithium diffusivity of fluorine-doped electrode is one order higher than that of fluorine-free electrode, which is ascribed to the enhanced electrical conductivity and interfacial stabilization effect.

• Elastomers and Composites
• /
• v.52 no.4
• /
• pp.257-265
• /
• 2017

In this work, CR (Chloroprene Rubber) was emulsified by phase-inversion emulsification with nonionic surfactants (NP-1025, LE-1017, and OP-1019) and an anionic surfactant (SDBS; sodium dodecylbenzenesulfonate), and its stabilization was investigated through a study of its adsorption characteristics, zeta potential, and flow behavior. As the amount of the mixed surfactant increased, the droplet size decreased, resulting in the increase of viscosity. In particular, a CR emulsion with a lower absorbance in the UV spectrum exhibited the highest zeta potential. The results of this experiment showed that the CR emulsion prepared using (LE-1017) and SDBS was the most stable. In this study, calcium hydroxide and aluminum hydroxide were added to enhance the mechanical properties of the CR emulsion, and the relationship between tensile strength, tear strength and surface free energy were investigated. The tensile and tear strengths of the CR emulsion incresed as the amount of calcium hydroxide and aluminum hydroxide increased. The highest tensile and tear strengths and surface free energy were observed for additions of 1.0% calcium hydroxide and 0.80% aluminum hydroxide, respectively. It was concluded that the interfacial bonding strength was improved by the even dispersion of calcium hydroxide and aluminum hydroxide in the CR emulsion.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.3
• /
• pp.134-142
• /
• 1995

We discovered that each distinct shape of the roof-shaped peaks of (111) facets, which are generated on (110) cross-section of the directly bonded (100) silicon wafer pairs after KOH etching, can be mapped to one of three conditions of the interfacial oxide existing at the bonding interface as follows. That is, thick solid line can be mapped to stabilization, thin solid line to disintegration, and thin broken line to spheroidization. also we confirmed that most of the interfacial oxides of a well-aligned wafer pairs were disintegrated and spheroidized through high-temperature annealing process above 900$^{\circ}$C while the oxide was stabilized persistently when two wafers are bonded rotationally around their common axis perpendicular to the wafer planes.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.3
• /
• pp.154-159
• /
• 2012

Structural volume change occurring on the Si-based anode battery materials during alloying/dealloying with lithium is noticed to be a major drawback responsible for a limited cycle life. Silicon monoxide has been reported to show relatively improved cycling performance compared to Si-containing materials for rechargeable lithium batteries, due to the structural buffering role of in-situ formed $Li_2O$ and lithium silicate during the reaction of silicon monoxide and lithium. Here we report improved cycling ability of interfacially stabilized Si-$SiO_2$-graphite composite anode using silane-based electrolyte additive for rechargeable lithium batteries, which includes low cost silicon dioxide for structural stabilization and graphite for enhanced conductivity.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.1
• /
• pp.32-38
• /
• 1999

A biosurfactant produced by Tsukamurella sp. 26A was purified by procedures including acid precipitation, ethylacetate extraction, and adsorption chromatography. The purified biosurfactant reduced the surface tension of water from 72 mN/m to 30 mN/m at a concentration of 250 mg/l, whereas the minimum interfacial tension against n-hexadecane was lowered to 1.5 mN/m at a concentration of 40 mg/i. The compound stabilized oil-in-water emulsions with a variety of commercial oils and had strong emulsification and stabilization activities when compared to those of commercial emulsifiers and stabilizers. Surface tension was stable over a broad range of pH (2-12) and temperature ($100^{\circ}C$, 3h). The biosurfactant was identified as glycolipid having a hydrophilic moiety of trehalose.

• Journal of the Korean Ceramic Society
• /
• v.27 no.5
• /
• pp.684-692
• /
• 1990

Ultrafine magnetite powder for the ferromagnetic fluid was prepared by an addition of alkaline solution to the solution containing Fe2+ and Fe3+ ions at 6$0^{\circ}C$. The optimum condition of the magnetite synthesis was delineated by examining such various physico-chemical properties as Fe2+/Fe+3 ratio in the powder, phase characteristics, MHC and $\sigma$max. A new scheme for the steric stabilization of colloidal dispersion was proposed using the concept of the buffer group action for the increased interfacial density of the stabilizing moieties at colloid particle/dispersion medium interface. The proposed concept was successfully applied to the preparation of the kinetically stable kerosinebased ferrofluid using Tween and Span as dispersants. In the dispersion of magnetite particles in a kerosine, Tween(polyoxyethylene sorbitan oleate) acts as a primary stabilizer which provides an anchor group, whereas Span(sorbitan oleate) can be classified as a secondary stabilizer which adsorbs on the surface of magnetite particle through the action of the buffer group. Dispersion studies using various quantities of Tween and Span supported the concept of the buffer group action for increased dispersion characteristics of the kerosine based ferromagnetic fluid.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.89-89
• /
• 2010

The atomic structure of Sb/Si(5 5 12)-$2{\times}1$ surface, deposited at room temperature (RT) and post-annealed, has been identified by scanning tunneling microscopy and the corresponding interface has been studied by synchrotron core-level photoemission spectroscopy. With 0.3-nm Sb deposition at RT and postannealing at $600^{\circ}C$, the surface has been facetted to (225)-$2{\times}1$ and (112)-$1{\times}1$, and its Si 2p has shown that all the Si 2p surface components have disappeared, while the single Sb-Si interfacial component has appeared. Such results indicate that all of surface Si atoms are replaced by Sb atoms and the charge is transferred from Si to passivating Sb-atoms at the top layer. With subsequent postannealing up to $700^{\circ}C$, the surface has been facetted to (113)-$2{\times}2$ and (335)-$4{\times}2$, still having Sb-Si interfacial component and partially re-exposed Si surface components. From the present study, the role of surfactant atom, Sb, as well as the thermal-stabilization of Sb-passivated high-index Si surface will be exposed. Especially, the key role of the Sb/Si(113)-$2{\times}2$, composed of Rebonded-Dimer-Rebonded atom 1D structures, for stabilization will be discussed.

• Elastomers and Composites
• /
• v.54 no.4
• /
• pp.335-344
• /
• 2019

In this work, styrene butadiene rubber (SBR) and styrene butadiene styrene (SBS) were used to modify asphalt, resulting in SBR- and SBS-modified asphalt, respectively. The two modified asphalts were emulsified with a nonionic emulsifier (Span 60) and cationic emulsifiers (ID, DDA) and their phase stabilization was investigated via particle size, Zeta potential, and flow behavior analysis. With increasing amount of the mixed emulsifier, the particle size decreased, leading to an increase in viscosity. The shear thinning behaviors and Zeta potential values ranging from 35-65 mV were determined and remained considerably stable. In addition, the adhesion strength and compression strength of the SBR-and SBS-modified asphalt emulsion were evaluated via surface free energy examination. The remarkable adhesion and compression strengths were estimated when 5 phr ID and 6 phr DDA were added to the emulsified asphalt modified with SBR and SBS. Therefore ID and DDA, the two cationic surfactants, played significant roles in improving the dispersion and interfacial adhesion strength, resulting in the improved adhesion and compression strength of the emulsified asphalts modified with SBR and SBS.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.8
• /
• pp.2005-2014
• /
• 2009

There are several methods to fabricate Polymer Dispersed Liquid Crystal(PDLC) films. One of them, so-called Nematic Curvilinear Aligned Phase(NCAP) film, is based on emulsion technology. To produce NCAP systems various water soluble polymers, such as partially hydrolyzed polyvinylalcohol(PVA) and polyvinyl pyrrolidone(PVP), which can form stable emulsion of liquid crystal(LC) without any stabilizers were used. In this work, we studied the dependence of emulsion stability on nature and composition of copolymers composed of water-soluble and water-insoluble moiety. We found that interfacial surface tension depends on the composition of comonomer, the copolymer concentration in the water, and the nature of hydrophobic chain. The Acrylamide -styrene(AA-ST) copolymer showed the lowest interfacial surface tension among the tested copolymers at the same concentration. Since the interfacial surface tension decreases with increasing the compatibility of copolymer with LC phase the AA-ST copolymer has the best compatibility with LC molecules. It is believed that molecules adsorbing easily on the surface of LC droplets allows the LC emulsion system to be more stable.

• Elastomers and Composites
• /
• v.36 no.4
• /
• pp.246-254
• /
• 2001

In this work, the stabilization of chlorosulfonated polyethylene (CSM) rubber emulsion with surfactants, i.e., nonionic (Span 60) or anionic (Sodium laurylsulfate, SLS) surfactants, was investigated. The phase inversion emulsification by interfacial chemical characteristics was used to emulsify the CSM rubber. As a result, the emulsion phase separation was observed in the case of any single surfactant. However, there was no phase separation in the mixture of Span 60 and SLS in the context of emulsion droplet size tests and rheological behaviors. The droplet size decreases by increasing the surfactant mixture, resulting in increasing the viscosity. The viscosity and shear stress determined from shear rate show a shear thinning and yield behaviors. It was then found that the emulsion stabilization can be improved using the phase inversion emulsification method and surfactant mixture.