• Applied Chemistry for Engineering
• /
• v.27 no.3
• /
• pp.291-298
• /
• 2016

In this study, zwitterionic surfactants were added to liposome systems at different pH conditions to understand the effect of surfactants on liposome characteristics. For this purpose, amine oxide surfactants having different hydrocarbon chain lengths were synthesized and the structure of the resulting product was elucidated by using $^1H$ NMR, $^{13}C$ NMR, and FT-IR. In addition, the physical properties of newly synthesized surfactants such as critical micelle concentration (CMC), surface tension and isoelectric point were measured. The stability characteristics of liposome systems including average particle sizes and zeta potentials were measured by varying pH and hydrocarbon chain lengths of an amine oxide surfactant. Effects of the pH and hydrocarbon chain length of an amine oxide surfactant on fluidity of a liposome membrane were also examined by measuring the deformability and the binding degree between the surfactant and liposome.

• Journal of Conservation Science
• /
• v.27 no.4
• /
• pp.403-414
• /
• 2011

This study is re-creational experiment of Goryeo gold-painted decoration based on the research of the gold remaining and gold painting technique on the two pieces of Goryeo gold-painted celadon and the three pieces of Chinese gold-painted porcelain on North Song period which ones have been owned by National Museum of Korea since 2007. For the observation of glue state and color developing ability, four kinds of agglutinative agent and gold powder were mixed over the porcelain sherds, then gradually fired from $100^{\circ}C$ to $1200^{\circ}C$. Visual effect and ideal temperature were measured. Among of them, oil and glue showed the best results in glue state and color developing ability. Through those results, the entire Goryeo engraved celadon were reproduced in modern facilities. Oil and glue were gold-painted over the glaze then it was fired at the ideal temperature 700 to $800^{\circ}C$. For observation the binding condition, the gold-painting cross section was looked by the scanning electron microscope (SEM). As the result, oil and glue did not make much difference in Agglutinative agent, but gold was good, the color developing ability, however, in the case of oil, the edge of gold is curled because of its interfacial tension, and it is not dried well at room temperature so the working property is not as good as the glue. Glue more effective in terms of work efficiency, but color developing ability to fall slightly in this experiment were able to see through.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.30 no.2
• /
• pp.102-111
• /
• 2014

Purpose: Surface damage and bonding strength difference after micromechanical treatment of zirconia surface are to be studied yet. The aim of this study was to evaluate the difference of fracture resistance and bonding strength between more surface-damaged group from higher air-blasting particle size and pressure, and less damaged group. Materials and Methods: Disk shape zirconia ($LAVA^{TM}$) was sintered and air-blasted with $30{\mu}m$ particle size (Cojet), under 2.8 bar for 15 seconds, $110{\mu}m$ particle size (Rocatec), under 2.8 bar for 15 seconds, and $110{\mu}m$ particle size (Rocatec), under 3.8 bar for 30 seconds respectively. Biaxial flexure test and bonding failure load test were performed serially (n = 10 per group). For bonding test, specimens were bonded on the base material having similar modulus of elasticity of dentin with $200{\mu}m$-thick resin cement for tension of surface damage. Failure load of bonding was detected with acoustic emission (AE) sensor. Results: There were no significant differences both in the biaxial flexure test and bonding failure load test between groups (P > 0.05). Sub-surface cracks were all radial cracks except for two specimens. Conclusion: Within the limitations of no aging under monotonic load test, surface damage from higher air-blasting particle size and pressure was not significant. Evaluations of failure load with bonded zirconia disks was clinically relevant modality for surface damage and bonding strength, simultaneously.

• Journal of Energy Engineering
• /
• v.24 no.1
• /
• pp.114-122
• /
• 2015

In the high convective gas flow condition, irregular shaped water waves from which droplet entrainment occurs are generated under horizontally stratified two-phase flow condition. KAERI proposed a new mechanistic droplet entrainment model based on the momentum balance equation consisting of the shear stress, surface tension, and gravity forces. However, this model requires correlation or experimental data of several physical parameters related to the wave characteristics. In the present study, we tried to measure the physical parameters such as wave slope, wave hypotenuse length, wave velocity, wave frequency, and wavelength experimentally. For this, an experiment was conducted in the horizontal rectangular channel of which width, height, and length are, respectively, 40 mm, 50 mm, and 4.2 m. In the present test, the working fluids are chosen as air and water. The PIV technique was applied not only to obtain images for phase interface waves but also to measure the velocity field of the water flow. Additionally, we developed the parallel wire conductance probe for the confirmation of wave height from PIV image. Finally, we measured the physical parameters to be used in the validation of new droplet entrainment model.

• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.21-28
• /
• 2006

This paper presents both experimental and analytical studies for the development of an ECC(Engineered Cementitious Composites) using ground granulated blast furnace slag(slag). This material has been focused on achieving moderately high composite strength while maintaining high ductility, represented by strain-hardening behavior in uniaxial tension. In the material development, micromechanics was adopted to properly select optimized range of the composition based on steady-state cracking theory and experimental studies on matrix, and interfacial properties. A single fiber pullout test and a wedge splitting test were employed to measure the bond properties of the fiber in a matrix and the fracture toughness of mortar matrix. The addition of the slag resulted in slight increases in the frictional bond strength and the fracture toughness. Subsequent direct tensile tests demonstrate that the fiber reinforced mortar exhibited high ductile uniaxial tension behavior with a maximum strain capacity of 3.6%. Both ductility and tensile strength(~5.3 MPa) of the composite produced with slag were measured to be significantly higher than those of the composite without slag. The slag particles contribute to improving matrix strength and fiber dispersion, which is incorporated with enhanced workability attributed to the oxidized grain surface. This result suggests that, within the limited slag dosage employed in the present study, the contribution of slag particles to the workability overwhelms the side-effect of decreased potential of saturated multiple cracking.

• The Korean Journal of Food And Nutrition
• /
• v.10 no.3
• /
• pp.302-308
• /
• 1997

The purpose of this study was to investigate the extraction yield and quality stability as to the oleoresin process with large amount of onion at one time. The first mixed-product is raw onion juice which was reduced the compression and concentrated by Brix 70% mixed together wit the residue which was extracted and concentrated by ethanol, the second product manufactured by the same method above after the autoclaving with onion, and the other product is made by grinding by 50mesh to freeze-dried onion. Each of yields were 7.3, 9.1 and 0.8% and each of total sugar content was 616.4, 712.3 and 150.3mg/g. Therefore the product extracted by ethanol from freeze-dried onion was very low in yield and total sugar content. By the index of the overall odor intensity, contents of total pyruvate were 1,733.7, 520.6, and 2,716.5$\mu\textrm{g}$/g for each product. As a result, oleoresin onion processing that desired to use raw onion was remarkable for odor recovery. For the homogenous mixture with concentrate of onion juice and ethanol extract were emulsified by the addition of 2% of PGDR(polyglycerol condensed ricinoleate) and agitation(10,000rpm, 30 minutes). At this time, interfacial tension was 1.9 dyne/cm and the formation of emulsion was for 96.2% when left over 24hours in 6$0^{\circ}C$. When it was to be centrifuged(2,000$\times$G, 80 minutes) after emulsification, the volume of emulsion level without seperation was 92.6%, and very high in emulsification stability. The induced heating-oxidize with soy bean oil and sesame oil added to 1% of onion oleoresin, induction-time extension effect appeared with antioxidant activity that was applicable for 80.8~82.2% as to the effect of addition of 0.02% BHA.