• 대한기계학회논문집A
• /
• 제27권7호
• /
• pp.1132-1137
• /
• 2003

This study dealt with the suppression of interfacial reaction between Nb and MoSi$_2$ for the fabrication of high toughness Nb/MoSi$_2$ laminate composites, based on the results of a thermodynamical estimation. Especially, the effect of ZrO$_2$ particle on the interfacial reaction of Nb/MoSi$_2$ bonding materials has been examined. Nb/MoSi$_2$ bonding materials have been successfully fabricated by alternatively stacking matrix mixtures and Nb sheets and hot pressing in the graphite mould. The addition of ZrO$_2$ particle to MoSi$_2$ matrix is obviously effective for promoting both the interfacial reaction suppression and the sintered density of Nb/MoSi$_2$ bonding materials, since it is caused by the formation of ZrSiO$_4$ in the MoSi$_2$-ZrO$_2$ matrix mixture. The interfacial shear strength of Nb/MoSi$_2$ bonding materials also decreases with the reduction of interfacial reaction layer associated with the content of ZrO$_2$ particle and the fabrication temperature.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.143-146
• /
• 2002

Unsized AS-4 carbon fibers were etched by RF plasma and then coated via plasma polymerization in order to enhance adhesion to vinyl ester resin. The gases utilized for the plasma etching were Ar, $N_2 and O_2$, while the monomers used for the plasma polymerization coating were acetylene, butadiene and acrylonitrile. The conditions for the plasma etching and the plasma polymerization were optimized by measuring interfacial adhesion with vinyl ester resin via micro-droplet tests. Among the treatment conditions, the combination of Ar plasma etching and acetylene plasma polymerization provided greatly improved interfacial shear strength (IFSS) of 69MPa compared to 43MPa with as-received carbon fiber. Based on the SEM analysis of failure surface and load-displacement curve, it was assume that the failure might be occurred at the carbon fiber and plasma polymer coating. The plasma etched and plasma polymer coated carbon fibers were subjected to analysis with SEM, XPS, FT-IR or Alpha-Step, and dynamic contact angles and tensile strengths were also evaluated. Plasma polymer coatings did not change tensile strength and surface roughness of fibers, but decreased water contact angle except butadiene plasma polymer coating, possibly owing to the functional groups introduced, as evidenced by FT-IR and XPS.

• 공업화학
• /
• 제23권3호
• /
• pp.313-319
• /
• 2012

본 연구에서는 Polyacrylonitrile (PAN)계 탄소섬유 표면에 구리도금 표면처리가 탄소섬유 강화 복합재료의 기계적 계면 특성에 미치는 영향에 관하여 관찰하였다. 탄소섬유 표면특성은 주사전자현미경, X-선 광전자 분광법, X-선 회절분석기, 접촉각 측정기로 측정하였고, 탄소섬유 강화 복합재료의 기계적 계면 물성은 층간전단강도(interlaminar shear strength, ILSS)와 파괴인성(critical stress intensity factor, $K_{IC}$)측정을 통하여 알아보았다. 실험결과로부터, 기계적 계면물성은 탄소섬유 표면에 COOH group과 도금된 구리함량이 증가됨에 따라 순차적으로 증가되는 것이 확인되었으나, 도금시간을 길게 하여 과량의 구리가 도입되었을 경우 기계적 계면 물성을 도리어 감소시키는 것으로 확인되었다. 결론적으로 구리함량이 탄소섬유 복합재료의 기계적 계면물성을 결정하는 중요 요소라 판단되나, 최적의 함량이상에서는 계면분리에 의한 물성저하의 원인이 될 수 있다.

• International Journal of Automotive Technology
• /
• 제8권4호
• /
• pp.483-491
• /
• 2007

A closed form solution of a composite mechanics system is performed for the investigation of elastic-plastic behavior in order to predict fiber stresses, fiber/matrix interfacial shear stresses, and matrix yielding behavior in short fiber reinforced metal matrix composites. The model is based on a theoretical development that considers the stress concentration between fiber ends and the propagation of matrix plasticity and is compared with the results of a conventional shear lag model as well as a modified shear lag model. For the region of matrix plasticity, slip mechanisms between the fiber and matrix which normally occur at the interface are taken into account for the derivation. Results of predicted stresses for the small-scale yielding as well as the large-scale yielding in the matrix are compared with other theories. The effects of fiber aspect ratio are also evaluated for the internal elastic-plastic stress field. It is found that the incorporation of strong fibers results in substantial improvements in composite strength relative to the fiber/matrix interfacial shear stresses, but can produce earlier matrix yielding because of intensified stress concentration effects. It is also found that the present model can be applied to investigate the stress transfer mechanism between the elastic fiber and the elastic-plastic matrix, such as in short fiber reinforced metal matrix composites.

• 접착 및 계면
• /
• 제3권2호
• /
• pp.17-29
• /
• 2002

Micromechanical 시험법과 표면 젖음성 측정을 이용한 implant용 생분해성 복합재료의 계면물성과 미세파괴 분해 메카니즘을 연구하였다. 분해시간이 경과함에 따라서 poly(ester-amide) (PEA)와 생활성 유리섬유의 인장강도와 탄성률 그리고 신율은 점차적으로 감소하는 경향을 보인 반면, chitosan 섬유는 거의 변화가 없었다. 생활성 유리섬유와 poly-L-lactide(PLLA) 사이의 계면전단강도는 PEA나 chitosan 섬유 시스템의 경우보다 더 큰 값을 보였으나, 계면전단강도 감소 속도는 가장 빨랐고 chitosan 섬유의 경우가 가장 느린 결과를 보였다. 접착일 ($W_a$)은 생활성 유리섬유와 PLLA 사이에서 가장 높은 값을 나타냈으며, 이러한 표면 젖음성 결과는 계면전단강도 결과와 잘 일치하였다. 계면물성과 미세파괴 분해 메카니즘은 생분해성 복합재료의 성능을 조절할 수 있는 가장 중요한 요인들이다.

• Geomechanics and Engineering
• /
• 제11권3호
• /
• pp.345-359
• /
• 2016

In order to investigate the influence of the interfacial angel on failure characteristics and mechanism of combined coal-rock mass, 35 uniaxial/biaxial compressive simulation tests with 5 different interfacial angels of combined coal-rock samples were conducted by PFC2D software. The following conclusions are drawn: (1) The compressive strength and cohesion decrease with the increase of interfacial angle, which is defined as the angle between structure plane and the exterior normal of maximum principal plane, while the changes of elastic modulus and internal friction angle are not obvious; (2) The impact energy index $K_E$ decreases with the increase of interfacial angle, and the slip failure of the interface can be predicted based on whether the number of acoustic emission (AE) hits has multiple peaks or not; (3) There are four typical failure patterns for combined coal-rock samples including I (V-shaped shear failure of coal), II (single-fracture shear failure of coal), III (shear failure of rock and coal), and IV (slip rupture of interface); and (4) A positive correlation between interfacial angle and interface effect is shown obviously, and the interfacial angle can be divided into weak-influencing scope ($0-15^{\circ}$), moderate-influencing scope ($15-45^{\circ}$), and strong-influencing scope (> $45^{\circ}$), respectively. However, the confining pressure has a certain constraint effect on the interface effect.

• Geomechanics and Engineering
• /
• 제14권3호
• /
• pp.233-240
• /
• 2018

Pullout tests are usually employed to determine the ultimate bearing capacity of reinforced soil, and the load-displacement curve can be obtained easily. This paper presents an analytical solution for predicting the full-range mechanical behavior of a buried planar reinforcement subjected to pullout based on a bi-linear bond-slip model. The full-range behavior consists of three consecutive stages: elastic stage, elastic-plastic stage and debonding stage. For each stage, closed-form solutions for the load-displacement relationship, the interfacial slip distribution, the interfacial shear stress distribution and the axial stress distribution along the planar reinforcement were derived. The ultimate load and the effective bond length were also obtained. Then the analytical model was calibrated and validated against three pullout experimental tests. The predicted load-displacement curves as well as the internal displacement distribution are in closed agreement with test results. Moreover, a parametric study on the effect of anchorage length, reinforcement axial stiffness, interfacial shear stiffness and interfacial shear strength is also presented, providing insights into the pullout behaviour of planar reinforcements of MSE structures.

• 대한치과기공학회지
• /
• 제29권2호
• /
• pp.141-150
• /
• 2007

The purpose of this study was to ascertain the bonding durability of self-etching dentin bonding agents to dentin by means of shear bonding strength. Several acid-etching dentin bonding system (ESPE Z100) and self-etching dentin bonding systems (DEN-FIL, GRADIA DIRET) were used. The occlusion surface of human molars were ground flat to expose dentin and treated with the etch bonding system according to manufactures instruction and followed by composite resin application. After 24hours of storage at 37$^{\circ}C$, the shear bonding strength of the specimens was measured in a universal testing machine with a 1mm/min crosshead speed. An one-way analysis of variance and the scheffe test were performed to identify significant differences (p<0.05). The bonded interfacial surfaces and treated dentin surfaces were examined using a SEM. Through the analysis of shear bond strength data and micro-structures of dentin-resin interfaces, following results are obtained. In dentin group, the shear bond strength of DEN-FIL showed statistical superiority in comparison to the other groups and followed by ESPE Z100 and GRADIA DIRECT (p<0.05).

• 한국안전학회지
• /
• 제30권6호
• /
• pp.7-11
• /
• 2015

The present study investigates the impact shear strength of thermal aged Sn-3Ag-0.5Cu lead-free solder joints at impact speeds ranging from 0.5 m/s to 2.5 m/s. The specimens were thermal aged for 24, 100, 250 and 1000 hours at $100^{\circ}C$. The experimental results demonstrate that the shear strength of the solder joint decreases with an increase in the load speed and aging time. The shear strength of the solder joint aged averagely decreased by 43% with an increase in the strain rate. For the as-reflowed specimens, the mode II stress intensity factor ($K_{II}$) of interfacial IMC between Sn-3.0Ag-0.5Cu and a copper substrate also was found to decrease from $1.63MPa.m^{0.5}$ to $0.97MPa.m^{0.5}$ in the speed range tested here. The degradations in the shear strength and fracture toughness of the aged solder joints are mainly caused by the growth of IMC layers at the solder/substrate interface.

• 마이크로전자및패키징학회지
• /
• 제12권1호
• /
• pp.87-93
• /
• 2005

Au 층의 두께를 $0.1{\~}0.7{\mu}m$로 변화시킨 $0.1{\mu}m$ Ti/3 ${\mu}m$ Cu/Au UBM 상에서 48Sn-52In 솔더를 $150-250^{\circ}C$의 온도 범위에서 리플로우시 UBM/솔더 반응에 의한 금속간화합물의 형성거동을 분석하였다. 또한 Ti/Cu/Au UBM의 Au 두께 및 리플로우 온도에 따른 볼 전단강도와 전단에너지를 분석하였다. $150^{\circ}C$와 $200^{\circ}C$에서 리플로우 시에는 UBM/솔더 계면에 $Cu_6(Sn,In)_5$와 $AuIn_2$ 금속간 화합물이 형성되어 있으나, $250^{\circ}C$에서 리플로우 시에는 솔더 반응이 크게 증가하여 UBM이 대부분 소모되었다. 볼 전단강도는 UBM/솔더 반응과 일치하지 않는 결과를 나타내었으나, 전단 에너지는 UBM/솔더 반응과 잘 일치하는 변화 거동을 나타내었다.