• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.93-96
• /
• 2002

It is said that the verification effort occupies about 50-70 percent of the total effort of a System-On-A-Chip. This paper aims to develop a test bench automation tool based on the abstraction of the interface protocols. This tool will allow designers to describe their test benches in a high level language such as C rather than VHDL or Verilog. It helps designers to save their verification time and effort.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.357-361
• /
• 1997

In this work surface damage of head and disk of head disk drive was analysed using an Atomic Force Microscpoe. The initial damage of the disk occurred by generation of extermely small wear particles. Also it was show that wear particles tend to pile up near the front side of the slider. The surface damage mechanism of drag test and contact-start-stop test was found to be quite similar.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.37-38
• /
• 2008

• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.08a
• /
• pp.158-158
• /
• 2008

• Bulletin of the Korean Space Science Society
• /
• 2004.10b
• /
• pp.60-60
• /
• 2004

• Proceedings of the Korean Society of Disaster Information Conference
• /
• 2015.11a
• /
• pp.246-249
• /
• 2015

본 연구에서는 해운대 해수욕장 연안정비사업 전후의 지형변화에 따른 이안류 발생 변화에 대해 분석하였다. 본 연구에서는 Matlab GUI (Graphical User Interface)로 개발한 HAECUM (HAE(海) Current Model)을 통하여 해운대 해수욕장의 해빈류를 모의 하였다. 분석에 사용된 데이터는 이상적인 경우와 실제 이안류가 발생한 상황에 대해 각각 적용하였으며, 상호비교의 효율성을 위하여 해빈류 장미도를 통해 비교 분석 하였다. 본 연구를 통해 해운대 해수욕장의 연안정비사업에 따른 해빈류 및 이안류에 대한 상관성 도출하였다.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.54 no.3
• /
• pp.107-116
• /
• 2005

The paper addresses modeling and analysis of a grid-connected photovoltaic generation system (PV system). PSCAD/EMTDC, an industry standard simulation tool for studying the transient behavior of electric power system and apparatus, is used to conduct all aspects of model implementation and to carry out extensive simulation study. This paper is aimed at sharing with the PSCAD/EMTDC user community our user-defined model for PV system applications, which is not yet available as a standard model within PSCAD/EMTDC. An equivalent circuit model of a solar cell has been used for modeling solar array. A series of parameters required for array modeling have been estimated from general specification data of a solar module. A PWM voltage source inverter (VSI) and its current control scheme have been implemented. A maximum power point tracking (MPPT) technique is employed for drawing the maximum available energy from the PV array. Comprehensive simulation results are presented to examine PV array behaviors and PV system control performance in response to irradiation changes. In addition, dynamic responses of PV array and system to network fault conditions are simulated and analysed.

• Journal of Environmental Science International
• /
• v.29 no.1
• /
• pp.95-108
• /
• 2020

Silver nanoparticles were loaded onto g-C₃N₄ (CN) with a nanoroll-type morphology (Ag/CN) synthesized using a co-polymerization method for highly selective conversion of toxic nitrobenzene to industrially-valuable aminobenzene. Scanning electron microscopy and high-resolution transmission electron microscopy (HRTEM) images of Ag/CN revealed the generation of the nanoroll-type morphology of CN. Additionally, HRTEM analysis provided direct evidence of the generation of a Schottky barrier between Ag and CN in the Ag/CN nanohybrid. Photoluminescence analysis and photocurrent measurements suggested that the introduction of Ag into CN could minimize charge recombination rates, enhancing the mobility of electrons and holes to the surface of the photocatalyst. Compared to pristine CN, Ag/CN displayed much higher ability in the photocatalytic reduction of nitrobenzene to aminobenzene, underscoring the importance of Ag deposition on CN. The enhanced photocatalytic performance and photocurrent generation were primarily ascribed to the Schottky junction formed at the Ag/CN interface, greater visible-light absorption efficiency, and improved charge separation associated with the nanoroll morphology of CN. Ag would act as an electron sink/trapping center, enhancing the charge separation, and also serve as a good co-catalyst. Overall, the synergistic effects of these features of Ag/CN improved the photocatalytic conversion of nitrobenzene to aminobenzene.

• Proceedings of the KIEE Conference
• /
• 2003.10b
• /
• pp.42-44
• /
• 2003

As the industry is developed, uses of various electric motor are increasing from general home to various fields of industry, and the kind becomes various daily. For these reasons, it is required to study the remote control and a package management about change of a speed drive system, the supervision of administration appliance by real time, and the collection and process data together using internet prevailed on industry whole. This paper deals with the development of a Web-Based remote control system for permanent magnet synchronous motor drives. The client/server system using TCP/IP protocols and DSP controller for remote control through internet and the Web interface that users can confirm data and state of PMSM(Permanent Magnet Synchronous Motor) is developed. This system is available for driving, braking, variable speed control and monitoring for PMSM in real time through administration program of Web-Based.

• The KSFM Journal of Fluid Machinery
• /
• v.1 no.1 s.1
• /
• pp.7-16
• /
• 1998

An interactive mode of grid generation system has been developed for a Navier-Stokes design procedure of axial flow compressors. The present grid generator adopts the multiblock H-grid structure, which simplifies the creation of computational grids about complex turbomachinery geometries and facilitate the manipulation of multiple grid blocks for multirow flow fields. The numerical algorithm adopts the combination of the algebraic and elliptic method to create the internal grids efficiently and quickly. The system consists of four separated modules, which are linked together with a common graphical user interface. The system input is made of the results of the preliminary design. The final grids generated from each module of the system are used as the preprocessor for the performance prediction of the two-or three-dimensional flow simulation inside the blade passage. Application to the blade design of the LP compressor was demonstrated to be very reliable and practical in support of design activities. This customized system are coupled strongly with the design procedure of the turbomachinery cascades using the Navier-Stokes technique.