• Journal of Korea Multimedia Society
• /
• v.9 no.3
• /
• pp.360-368
• /
• 2006

Recently, performance of the mobile phone has increased dramatically. Due to this, it is possible to integrate various biotechnology. There are many ventures to integrate biotechnology with mobile phone, because of increasement interest of peoples well-being. The transcutaneous electrical nerve stimulation can Improve the circulation of blood and suppress a pain. To integrate the transcutaneous electrical nerve stimulation with mobile phone, it is necessity to make small, low power, and safe module. In this paper, the transcutaneous electrical nerve stimulation module is designed and implemented by small boost convertor. The value of tank capacitor, which is the total stimulus energy to human, can be chosen to insure safe condition. The confirm the of operation of designed module, a small micro-controller is used to make system and test the module. The implemented system is small and consumes a low enough power to be integrated with mobile phone.

• Journal of the Institute of Convergence Signal Processing
• /
• v.19 no.1
• /
• pp.28-34
• /
• 2018

This paper is composed of a passenger management system using a temperature sensing module, a PIR sensor module for detecting movement inside a room, and a smart breath sensing module for determining a sleeping state. An embedded sensor module and a communication system integrated the sensing part and the algorithm driving part. As the aging society is accelerating and becoming more upgraded, the social cost of Silver Care increases, and in order to protect privacy, it is necessary to reduce costs by developing efficient smart silver care devices. The proposed non - image human body detection IOT sensor system is implemented by hardware and software and has superior performance compared with conventional image monitoring method.

• Journal of Satellite, Information and Communications
• /
• v.5 no.2
• /
• pp.82-86
• /
• 2010

In this paper, a power amplifier module for WCDMA base-station applications is designed and implemented using GaN field-effect transistors (FETs), which uses an envelope tracking bias system. The designed module consists of an high gain MMIC amplifier, a driver amplifier, a power amplifier, and bias circuits for envelope tracking applications. Especially, a FET bias sequencing circuit and two isolators are integrated for stable RF operations. All circuits are assembled within a single housing, so its dimension is just $17.8{\times}9.8{\times}2.0\;cm3$. Measured results show that the developed power amplifier module has good envelope tracking capability: the power-added efficiency of 35% at the output power range from 30dBm to 40dBm over a wide range of drain bias.

• The Research Journal of the Costume Culture
• /
• v.20 no.2
• /
• pp.222-237
• /
• 2012

Air-containing fashion, which can offer diverse functions through the inflow and outflow of air, is highly relevant in today's mobile society, where people are experiencing a wider range of environments. This study attempts to suggest the possibility of air-containing multi-functional fashion that could continuously be utilized by developing a design for an air-containing jacket using modular systems. In this research, the modular systems in architecture and furniture design were referenced through a review of the literature for the purpose of establishing modular systems in fashion. Functions relevant to the mobility of today's society are derived from the results of advanced research and applied to the design of modules of the jacket. The modules are integrated through the modular systems. The folding and unfolding structure in architecture and furniture is applied as a folding system in fashion, the vertical accumulation structure as a layering system, and the horizontal integration structure as a combining system, and in addition, the containing system has emerged in fashion. Each module is designed to fulfill certain functions, such as cushioning, heat insulation, and portability. The folding system is utilized in designing the cushion module to support the neck and back of a wearer by making its hood and hem fold in the back. The application of a layering system was suggested by making the vest, combined with the neck cushion and back cushion via the combining system, layered with its insulation module. By applying the combining system, the hood that includes the neck cushion, the skirt that includes the back cushion, the body that includes the insulation module, and the sleeves can be connected and separated by a zipper. The applicability of this concept was proven by applying a developed design to an actual item.

• Current Photovoltaic Research
• /
• v.3 no.4
• /
• pp.121-125
• /
• 2015

BIPV system is one of the best ways to harness PV module. The BIPV system not only produces electricity, but also acts as a building envelope. Thus, it has the strong point of increasing the economical efficiency by applying the PV modules to the buildings. Bifacial solar cells can convert solar energy to electrical energy from both sides of the module. In addition, it is designed as 3 busbar layout which is the same with ordinary mono-facial soalr cells. Therefore, many of the module manufacturers can easily produce the bifacial solar cells without changing their manufacturing equipment. Moreover, bifacial BIPV system has much potential in building application by utilizing glass to glass structure. However, the performance of bifacial solar cells depends on a variety of factors, ranging from the back surface to surrounding conditions. Therefore, in order to apply bifacial solar cells to buildings, an analysis of bifacial PV module performance should be carried out that includes a consideration of various design elements, and reflects a wide range of installation conditions. As a result it found that the white insulation reflector type can improve the performance of the bifacial BIPV system by 16%, compared to the black insulation reflector type. The performance of the bifacial BIPV was also shown to be influenced by inclination angle, due to changes in both the amount of radiation captured on the front face and the radiation transmitted to the rear face through the transparent space. In this study is limited design condition and installation condition. Accordingly follow-up researches in this part need to be conducted.

• Journal of Advanced Navigation Technology
• /
• v.8 no.2
• /
• pp.105-111
• /
• 2004

This paper describes the design of navigation system for an unmanned target drone which is operated by Korean army as for anti-air gun shooting training. Current target drone is operated by pilot control of on-board servo motor via remote control system. Automatic flight control system for the target drone greatly reduces work load of ground pilot and can increase application area of the drone. Most UAVs being operated nowdays use high-priced sensors as AHRS and IMU to measure the attitude, but those are costly. This paper introduces the development of low-cost automatic flight control system with low-cost sensors. The integrated automatic flight control system has been developed by integrating combining power module, switching module, monitoring module and RC receiver as an one module. The performance of navigation for low cost unmanned aerial vehicle, unmanned target drone as our test bed in this paper is verified by both Hardware in the loop simulation(HILS) to test performance of GPS as GPS output frequency high and results of flight test.

• Smart Media Journal
• /
• v.7 no.4
• /
• pp.9-16
• /
• 2018

In order to improve the economics and flexibility of cloud computing, tendency to automate the operation and management of cloud resources has become complicated. However, while automation for cloud storage depends on the manufacturer's storage hardware, it cannot flexibly support the storage type in accordance with users' needs. In this paper, we propose an automatic configuration module that supports block/file/object storages suitable for user environment. In order to automatically install ceph, a cloud storage, we propose an automatic installation and configuration module based on the Chef configuration management tool. In addition to that, we also propose an automatic configuration module based on a shell programming in pursuit of enabling users to use ceph storage of block/file/object. The proposed method can automatically set up and manage shared file, block, and object storages in a virtual or physical user environment with no hardware dependencies.

• Convergence Security Journal
• /
• v.19 no.2
• /
• pp.83-89
• /
• 2019

In accordance with information security compliance and security regulations, there is a need to develop regular and real-time concepts for cyber-infringement attacks against network system vulnerabilities in branch and periodic forms. Vulnerability Analysis Analysis It is judged that it will be a countermeasure against new hacking attack in case of concept validation by interworking with TOOL. Vulnerability check module is standardized in event attribute management and ease of operation. Opening in terms of global sharing of vulnerability data, owasp zap / Angry ip Etc. were investigated in the SIEM system with interlocking design implementation method. As a result, it was proved that the inspection events were monitored and transmitted to the SIEM console by the vulnerability module of web and network target. In consideration of this, ESM And SIEM system In this paper, we propose a new vulnerability analysis method based on the existing information security consultation and the results of applying this study. Refer to the integrated interrelationship analysis and reference Vulnerability target Goal Hacking It is judged to be a new active concept against invasion attack.

• Fashion & Textile Research Journal
• /
• v.18 no.3
• /
• pp.363-373
• /
• 2016

This study aims to develop an all-fabric integrated smart jacket in order to create a temperature-regulating system based on a user experience design. For this research, previous research technologies of a textile switch interface and a temperature-regulating system were utilized and a unifying technology for the all-fabric integrated smart jacket was developed which can provide the appropriate temperature environments to the human body. A self-heating textile was applied at the areas of the back and hood in the final tested jacket, and an embroidery circuit was developed in the form of a rectangle in the back and in both ears of the hood, taking into account the pattern of the jacket part where it was be applied and the embroidery production method. The textile switch interface was designed in a three-layer structure: an embroidery circuit line in a conductive yarn, an interval material, and a conductive sensing material, and it was made to work with the input and output sensors through the multiple input method. After the all-fabric integrated smart jacket was produced according to the pattern, all of the textile band lines for transmission were gathered and connected with a miniature module for controlling temperature and then integrated into the inside of the left chest pocket of the jacket. After the users put on this jacket, they were asked to assess the wearing satisfaction. Most of them reported a very low level of irritation and discomfort and said that the jacket was as comfortable as everyday clothing.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.26 no.6
• /
• pp.571-581
• /
• 2008

With the advent of u-City(ubiquitous city) concept, the importance of urban management has been increased. GIS is a foundation for the efficient urban management and an essential technology for the development of u-City. u-City, which aims for convenient, safe, healthy, and comfortable life, provides diverse services based on advanced information technologies, and it will offer more services in the future. u-City integrated management platform enables the ease of service development, guarantees the quality of services for the resident, and provides organic information sharing. Moreover, the platform by integrating GIS and other common management functions, makes possible efficient urban management. In this paper, required functions of u-City integrated management platform for u-City service were analyzed. As a result, GIS module for management of street lights and supervision of fire was developed and the application usability of u-City integrated management platform was verified by service simulation.