• Journal of Advanced Marine Engineering and Technology
• /
• 제39권8호
• /
• pp.849-855
• /
• 2015

A better flow condition for the intake of pump is provided by the sump pump that connects the forebay to the intake of the pump station. If the suction sump is improperly shaped or sized, air-entraining vortices or submerged vortices may develop. These phenomena may greatly affect pump operation if vortices become sufficiently large. Moreover, any remaining vortices in the pump flow passage may result in an increase in the noise and vibration of the pump. Therefore, the vortices in the pump flow passage must be reduced to achieve good pump sump station performance. In this study, the effect of suction pipe leaning angle on the pump sump's internal flow is investigated. Additionally, a pipe type with an elbow shape is investigated. The results show that the air entraining vortices occur under the condition of a water level ratio H/D = 1.31 for each suction pipe type.

• 한국가시화정보학회지
• /
• 제9권3호
• /
• pp.59-64
• /
• 2011

In this study the change of free surface vortex is expressed through the time volume fraction using multiphase unsteady condition in sump, because in previous studies of the pump sump did not represent the behavior of the free surface vortex exactly due to the reason it was calculated using single phase and steady condition. The reliability of the computational analysis is verified through comparing experimental results with that of present numerical analysis. Homogeneous free surface model is used to apply interactions of air and water. The results show that the free surface vortex can be identified on the isotropic surface at air volume fraction 1%~5%. The vortices make an air column from the free surface to the sump intake and are created and destroyed repeatedly. The behavior of free surface vortex at numerical analysis is quite similar to experimental test. The result of vortex motion according to time, works on a cycle.

• 한국분무공학회지
• /
• 제5권3호
• /
• pp.9-16
• /
• 2000

In a SI engine, three-way catalyst converter has the best efficiency when A/F ratio is near the stoichiometry. The feedback control using oxygen sensors in the commercial engine has limits caused by the system delays. So it is necessary to control fuel quantity in accordance with intake air amount in order to reduce exhaust emission and improve the specific fuel consumption. Precise A/F ratio control requires measurement of air amount with respect to the cylinder and injection fuel according to the air amount In this paper, we applied nonlinear fuel injection model and developed the algorithm of A/F ratio control. This algorithm includes the methods of measurement of transient air mass flowing into each cylinder, of calculation of injection pulse width for measured air mass, and the method of feedback and engine control by using lambda sensor. Also we developed control program for IBM-PC by using C++ Builder, and tested it in the commercial engine.

• 한국자동차공학회논문집
• /
• 제6권6호
• /
• pp.252-258
• /
• 1998

In a SI engine, it is necessary to control fuel quantity in accordance with intake air amount in order to reduce exhaust emission and improve the specific fuel consumption. Generally the map data is used for the vehicles with a SI engine. For the precise control of air-fuel ratio, the real time control method is recommended rather than the control method using map data. In this paper, we developed real time control system using microprocessor and IBM-PC, and applied it to the commercial SI engine. We got good results for air-fuel ratio under the idle condition.

• 대한기계학회논문집B
• /
• 제39권1호
• /
• pp.45-51
• /
• 2015

최근 강화되는 연료소비율과 배기 규제에 대응하기 위해 자동차용 엔진에 다양한 신기술들이 적용되고 있다. 직접분사식 희박연소 엔진은 안정적인 성층혼합기 연소를 통해 연료소비율 및 배출가스 개선이 가능하지만 과잉공기 조건에서 상대적으로 높은 수준은 질소산화물의 배출은 해결되어야 할 과제이다. 본 연구에서는 직접분사식 희박연소 LPG 엔진에서 가변 밸브 기구를 이용한 흡기 및 배기밸브 시기의 변경이 엔진의 성능 및 배출가스에 미치는 영향을 파악하고자 하였다. 스로틀링을 하지 않은 부분부하 운전 조건에서 흡기밸브 열림 시기의 진각은 공기과잉률의 증가에 의한 질소산화물 배출 증가에 원인으로 작용하였다. 배기밸브 열림 시기를 진각할 경우 팽창일 감소와 펌핑손실 증가에 의해 연료 소비율이 악화되었다.

• 대한기계학회논문집B
• /
• 제28권1호
• /
• pp.59-65
• /
• 2004

The configuration of intake port and piston is a dominant factor of inlet air flow and mixture formation in an engine cylinder, resepectively. This study has analyzed intake port and piston characteristics for swirl flow of a heavy-duty LPG engine. As an available technology to optimize intake port, the steady flow rig test has been applied for measuring swirl ratio and mean flow coefficient. And we measured the mean velocity and turbulence intensity of swirl flow under motoring condition in transparent engine cylinder by backward scattering LDV system. From these results, the piston and cylinder head with a good evaluated swirl flow characteristics were developed and adapted fur a 11L heavy-duty engine using the liquid phase LPG injection (LPLI) system. The obtained results are expected to be a fundamental data for developing intake port and piston.

• 한국가스학회지
• /
• 제25권5호
• /
• pp.11-18
• /
• 2021

수소는 동일한 공연비(AF ratio, Air-to-fuel ratio)에서 가솔린에 비해 점화에너지가 현격히 낮기 때문에, 희박한 혼합기 조건에서도 안정적으로 연소할 수 있는 장점을 가지고 있어 연소를 기반으로하는 내연기관에도 적용이 가능하다. 그러나 일부 연소조건에서 역화(Back-fire) 혹은 조기 점화(Pre-ignition)와 같은 이상 연소가 발생하기 쉬운 문제를 가지고 있다. 따라서 본 연구에서는 엔진의 흡기(Intake gas mixture)를 구성하는 신기(Fresh air)와 수소 연료를 각각 냉각하여 공급함으로써, 역화를 최소화하여 최고 출력을 향상하는 연구를 진행하였다. 2.4 L급 전기점화(SI, Spark-ignition)엔진이 사용되었으며 수소는 포트분사 방식(PFI, Port Fuel Injection)으로 공급하였다. 신기의 온도는 터보차저가 장착된 상황에서 인터쿨러(Intercooler)를 이용하여 제어하였으며, 수소의 냉각은 칠러의 냉매와 열교환기를 통하여 직접 냉각 후 공급하였다. 그 결과 신기의 온도를 10~20 ℃가량 냉각시킬 경우 최고출력이 약 6.5~8.6 % 가량 향상되는 것을 확인할 수 있었으며, 수소를 -6 ℃까지 냉각하여 공급할 경우 마찬가지로 약 7.7 % 가량의 최고 출력을 향상할 수 있었다.

• 대한전기학회논문지
• /
• 제38권9호
• /
• pp.724-732
• /
• 1989

The structure of engine and its interaction are investigated and the construction of mathematical model for the performance evaluation is presented and then simulated. The total system is classified as air-fuel inlet element, intake manifold, combustion, and engine dynamics and their control function are schematically evaluated. Because of the model structure with general engine function and computer simulation of the chosen engine, physical characteristics of the corresponding engine and the engine data of normal operation state are used. According to the study, it is possible to predict the mixture rate by by the difference in the mass of fuel and air into cylinder and to evaluate and trace dynamic characteristic of operation state under various operating condition. The model characteristic under the transient operating condition makes it possible to effectively evaluate the operation of actual engine through the result of simulation.

• International Journal of Automotive Technology
• /
• 제8권4호
• /
• pp.437-444
• /
• 2007

This paper experimentally investigates the effects of oxygen-enriched air (OEA) on the running behaviors of an LPG SI engine during both start/warm-up (SW) and hot idling (HI) stages. The experiments were performed on an air-cooled, single-cylinder, 4-stroke, LPG SI engine with an electronic fuel injection system and an electrically-heated oxygen sensor. OEA containing 23% and 25% oxygen (by volume) was supplied for the experiments. The throttle position was fixed at that of idle condition. A fueling strategy was used as following: the fuel injection pulse width (FIPW) in the first cycle of injection was set 5.05 ms, and 2.6 ms in the subsequent cycles till the achieving of closed-loop control. In closed-loop mode, the FIPW was adjusted by the ECU in terms of the oxygen sensor feedback. Instantaneous engine speed, cylinder pressure, engine-out time-resolved HC, CO and NOx emissions and excess air coefficient (EAC) were measured and compared to the intake air baseline (ambient air, 21% oxygen). The results show that during SW stage, with the increase in the oxygen concentration in the intake air, the EAC of the mixture is much closer to the stoichiometric one and more oxygen is made available for oxidation, which results in evidently-improved combustion. The ignition in the first firing cycle starts earlier and peak pressure and maximum heat release rate both notably increase. The maximum engine speed is elevated and HC and CO emissions are reduced considerably. The percent reductions in HC emissions are about 48% and 68% in CO emissions about 52% and 78%; with 23% and 25% OEA, respectively, compared to ambient air. During HI stage, with OEA, the fuel amount per cycle increases due to closed-loop control, the engine speed rises, and speed stability is improved. The HC emissions notably decrease: about 60% and 80% with 23% and 25% OEA, respectively, compared to ambient air. The CO emissions remain at the same low level as with ambient air. During both SW and HI stages, intake air oxygen enrichment causes the delay of spark timing and the increased NOx emissions.

• 수산해양기술연구
• /
• 제46권4호
• /
• pp.487-494
• /
• 2010

In order to test the applicability of bunker-A in a diesel engine for small-fishing boat, the investigation of the engine performance and the exhaust emission was performed under various conditions of fuel property, intake air pressure and fuel temperature. It was also performed based on IMO NOx Technical code. At high load, the energy consumption rate of bunker-A was lower than that of diesel oil, and the characteristics of exhaust emission of bunker-A were similar to those, and NOx emission rates of both fuels satisfied the IMO NOx emission regulation limits. The energy consumption rate and characteristics of exhaust emission were improved as the intake air pressure was increased, but these were not improved remarkably as the temperature of bunker-A was heated. However, at low load the energy consumption rate, CO emission rate and HC emission rate of bunker-A were higher than those of diesel oil, but NOx emission rates of the fuels were about the same. In addition, at low load the energy consumption rate and CO emission rate of bunker-A were increased as the intake air pressure and the temperature were higher than normal conditions. Accordingly, it is thought that the use of bunker-A in a kind of test engine is possible at high load. On the other hand, it is thought that more research is needed to improve the combustion efficiency under low temperature and low load condition.