• 한국초전도ㆍ저온공학회논문지
• /
• 제9권2호
• /
• pp.27-30
• /
• 2007

The electrical insulation design and withstanding test of mini-model coils for 600 kJ class conduction cooled high temperature superconducting magnetic energy storage (HTS SMES) have been studied in this paper. The high voltage is generated to both ends of magnet of HTS SMES by quench or energy discharge. Therefore, the insulation design of the high voltage needs for commercialization, stability, reliability and so on. In this study, we analyzed the insulation composition of a HTS SMES, and investigated about the insulation characteristics of the materials such as Kapton, AIN and vacuum in cryogenic temperature. Base on these results, the insulation design for 600 kJ conduction cooled HTS SMES was performed. The mini-model was manufactured by the insulation design, and the insulation test was carried out using the mini-model.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2018년도 춘계 학술논문 발표대회
• /
• pp.277-278
• /
• 2018

Improvement of insulation performance of buildings is a major part. Adiabatic method The adiabatic method minimizes the heat loss of the building. External insulation uses insulation to prevent fire. Ambient air hazards are less prone to fire. When a fire occurs, a phenolic pattern is formed and bond strength with the wall increases. EPS insulation and phenol foam were used to compare external heat transfer and external heat transfer. The heat transfer properties of phenolic foam and styrofoam were evaluated as follows. In the mortar and styrofoam structure, the problem of styrofoam reaching the burning point occurred before the collapse of the mortar, and the phenol foam had a problem in that when the direct fire was continued on the phenol foam. The characteristics of continuous infiltration appeared. In the case of mortar and phenol foam + styrofoam, the heat penetrated into the interior due to the shrinkage due to the shrinkage of the carbon screen on the phenol foam. However, when reinforced with glass mesh on the outer surface, And to reduce infiltration.

• 센서학회지
• /
• 제33권2호
• /
• pp.93-97
• /
• 2024

With the development of promising future mobility and urban air mobility (UAM) technologies, the demand for LIDAR sensors has increased. The SWIR photodetector is a sensor that detects lasers for the 3D mapping of lidar sensor and is the most important technology of LIDAR sensor. An SWIR photodetector based on QDs in an eye-safe wavelength band of over 1400 nm has been reported. QDs-based SWIR photodetectors can be synthesized and processed through a solution process and have the advantages of low cost and simple processing. However, the organic ligands of QDs have insulating properties that limit their ability to improve the sensitivity and stability of photodetectors. Therefore, the technology to replace organic ligands with inorganic ligands must be developed. In this study, the organic ligand of the synthesized PbS QDs was replaced with a MAPI inorganic ligand, and an SWIR photodetector was fabricated. The analysis of the characteristics of the manufactured photodetector confirmed that the photodetector based on MAPI-capped PbS QDs exhibited up to 26.5% higher responsivity than that based on organic ligand PbS QDs.

• 반도체디스플레이기술학회지
• /
• 제23권2호
• /
• pp.87-91
• /
• 2024

SiO₂, renowned for its excellent insulating properties, has been used in the semiconductor industry as a valuable dielectric material. High-quality SiO₂ films find applications in gate spacers and interlayer insulation gap-fill oxides, among other uses. One of the prevalent methods for depositing these SiO₂ films is plasma enhanced chemical vapor deposition (PECVD) favored for its relatively low processing costs and ability to operate at low temperatures. However, compared to the increasingly utilized atomic layer deposition (ALD) method, PECVD exhibits inferior film characteristics such as uniformity. This study aims to produce SiO₂ films with uniformity as close as possible to those achieved by ALD through the adjustment of PECVD process parameters. we conducted a total of nine PECVD processes, varying the process time and gas flow rates, which were identified as the most influential factors on the PECVD process. Furthermore, ellipsometry analysis was employed to examine the uniformity variations of each process. The experimental results enabled us to elucidate the relationship between uniformity and deposition rate, as well as the impact of gas flow rate and deposition time on the process outcomes. Additionally, thickness measurements obtained through ellipsometer facilitate the identification of optimal process parameters for PECVD.

• 공업화학
• /
• 제26권3호
• /
• pp.275-279
• /
• 2015

전도성 고분자인 poly(3,4-ethylenedioxythiophene) : poly(styrenesulfonate) (PEDOT : PSS)는 우수한 전기 전도도와 광투과도, 유연성을 가지고 있기 때문에 유기태양전지와 유기발광소자의 투명전극으로서 많은 각광을 받고 있다. PEDOT : PSS의 전기 전도도는 솔벤트를 도핑함에 따라 큰 폭으로 증가한다는 사실은 잘 알려져 있다. 본 연구에서는 다양한 솔벤트의 도핑과 솔벤트 후처리 공정에 따른 PEDOT : PSS 박막의 전기 전도도와 구조적 특성 변화를 연구하였다. 솔벤트 도핑으로 PEDOT : PSS의 전도도는 884 S/cm까지 증가하였고, 후처리 공정을 통해서 1131 S/cm의 전도도 값을 얻을 수 있었다. 이러한 전도도의 증가는 PSS 물질이 빠져나가거나 구조적인 재배열에 따른 전도성 PEDOT 입자의 접촉 면적이 증가함에 따른 것으로 사료되고, 광학적인 방법으로 PSS의 추출을 관찰하였다. 솔벤트 후처리 공정은 PEDOT : PSS 박막의 전도도를 향상하는 매우 효과적인 방법으로 확인되었고, 저가형 플렉서블 유기전자소자의 투명전극으로써의 사용이 적합할 것으로 예상된다.

• Journal of Electrical Engineering and Technology
• /
• 제13권6호
• /
• pp.2402-2411
• /
• 2018

Fluoronitriles-$CO_2$ gas mixtures are promising alternatives to $SF_6$ in environmentally-friendly gas-insulated transmission lines (GILs). Insulating gas heat transfer characteristics are of major significance for the current-carrying capacity design and operational state monitoring of GILs. In this paper, a three-dimensional calculation model was established for a GIL using the thermal-fluid coupled finite element method. The calculated results showed close agreement with experimentally measured data. The temperature distribution of a GIL filled with the Fluoronitriles-$CO_2$ mixture was obtained and compared with those of GILs filled with $CO_2$ and $SF_6$. Furthermore, the effects of the mixture ratio of the component gases and the gas pressure on the temperature rise and current-carrying capacity of the GIL were analyzed. Results indicated that the heat transfer performance of the Fluoronitriles-$CO_2$ gas mixture was better than that of $CO_2$ but worse than that of $SF_6$. When compared with $SF_6$, use of the Fluoronitriles-$CO_2$ gas mixture caused a reduction in the GIL's current-carrying capacity. In addition, increasing the Fluoronitriles gas component ratio or increasing the pressure of the insulating gas mixture could improve the heat dissipation and current-carrying capacity of the GIL. These research results can be used to design environmentally-friendly GILs containing Fluoronitriles-$CO_2$ gas mixtures.

• 한국지반환경공학회 논문집
• /
• 제19권3호
• /
• pp.15-24
• /
• 2018

전자기파는 주변 매질의 전기전도도와 유전율에 민감한 영향을 받기 때문에 지반의 특성을 평가하는데 널리 이용되고 있다. 본 연구에서는 염수환경에서도 다양한 농도의 중금속을 검측하기 위하여 시간영역반사법을 이용한 전자기파 측정 프로브를 제작하였다. 중금속으로는 구리를 사용하였으며, 실내 실험을 통해 구리 농도에 따라 적용 가능한 프로브를 선정하였다. 실내 실험에서는 염도 3%의 염수에 용해된 구리의 농도가 0, 0.01, 0.05, 0.1, 0.5, 1, 5, 그리고 10mg/L가 되도록 8단계로 용액을 조성하였다. 프로브는 염수에서도 전자기파를 측정할 수 있도록 5가지의 각기 다른 절연재로 코팅하여 비교하였다. 코팅재로는 에폭시, 탑코트, 바니쉬, 아크릴페인트, 히팅튜브를 사용하였으며 코팅재에 따른 전자기파의 신호 특성을 분석하였다. 실험 결과, 아크릴페인트와 히팅튜브로 코팅된 프로브는 구리 농도에 따른 신호 변화가 관측되지 않았으며, 에폭시, 탑코트, 바니쉬의 경우 구리 농도가 증가함에 따라 반사된 전자기파의 전압의 크기가 감소하는 것으로 나타났다. 에폭시로 1회 코팅한 프로브와 탑코트로 코팅한 프로브는 구리의 농도가 5mg/L 이하일 때 민감한 반응을 보였으나 에폭시로 2회 코팅한 경우, 구리의 농도가 5mg/L보다 클 때 더 민감하게 반응하였다. 본 연구의 결과는 절연재로 코팅된 시간영역반사법을 이용한 전자기파 측정 프로브가 염수에 녹아있는 중금속의 농도를 평가하는데 활용될 수 있음을 보여준다.

• 마이크로전자및패키징학회지
• /
• 제13권1호통권38호
• /
• pp.37-42
• /
• 2006

유기 박막트랜지스터(OTFTs)제작에서 PVP-게이트 절연막의 형성과 처리가 소자성능에 미치는 영향을 조사하였다. 유기 게이트 용액의 제조에서는 polyvinyl 계열의 PVP(poly-4-vinylphenol)를 용질로, PGMEA (propylene glycol monomethyl ether acetate)를 용매로 사용하였다. 또한 열경화성 수지인 poly(melamine-co-formaldehyde)를 경화제로 사용하여 유기 절연막의 cross-link를 시도하였다. MIM 시료의 전기적 절연 특성을 측정한 결과, PVP-기반 유기 절연막은 용액의 제조에서 PGMEA에 대한 PVP와 poly (melamine-co-formaldehyde)의 농도를 증가시킬수록 낮은 누설전류 특성을 나타내었다. OTFT 제작에서는 PGMEA에 대해 PVP를 20 wt%로 섞은 PVP(20 wt%) copolymer와 5 wt%와 10 wt%의 poly(melamine-co-formaldehyde)를 경화제로 추가한 cross-linked PVP(20 wt%)를 게이트 유전 재료로 사용하였다. 제작된 트랜지스터들에서 전계효과 이동도는 5 wt % cross-linked PVP(20 wt%) 소자에서 $0.31cm^2/Vs$로, 그리고 전류 점멸비는 10 wt% cross-linked PVP(20 wt%) 소자에서 $1.92{\times}10^5$으로 가장 높게 나타났다.

• 대한기계학회논문집A
• /
• 제39권11호
• /
• pp.1175-1181
• /
• 2015

일반적으로 산업현장에서 많이 사용되고 있는 단열재는 유리섬유와 같은 열전도도가 낮은 재료를 사용함으로써 단열성능을 확보하고 있다. 이와 달리 원전용 금속단열재의 경우 높은 열전도도를 가진 TP 304 스테인리스 박판을 재료로 한정하고 있어 단열성능을 확보하기 위해서는 구조적 측면에서의 접근이 필요하다. 본 연구에서는 금속단열재 내부구조에 대한 설계인자를 전도, 대류, 복사로 구성된 3가지 열전달 모드를 고려해 추출하고 각 인자들이 열전달에 미치는 영향과 각각의 열전달이 전체 열전달에 차지하는 비율을 열 유동해석을 이용하여 파악하고자 하였다. 본 연구를 통해 단열재 내부에서 발생되는 대류현상을 최소화하기 위해 다수의 박판을 삽입함과 동시에 증가하는 전도 비율을 비교하여 내부형상결정을 위한 세 가지 열전달 모드 하에서의 단열성능을 분석하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1081-1084
• /
• 1995

Internal voids located within an insulation will arise partial discharge that causes local breakdown and even the entire insulation breakdown. For HV apparatuses, it is usual case that several voids are formed within non-uniform electric field condition rather than single void within uniform field, which can be solved analitically. The purpose of this work is to study partial discharge and breakdown characteristics of an insulation according to the distribution pattern of two disc-type voids that are located within non-uniform field. The results from numerical field analysis and experiments show that the electric field within the voids decreases as they are arranged more serially, which accordingly results in the increase of partial discharge inception field(PDIF) much higher than that of single void model. With parallel arranged voids, PDIF is almost the same as that of single void model. On the other hand, AC breakdown strength decreases as voids are arranged more serially, which is a natural result considering the reduction of effective insulation thickness. For parallel voids, this effect cannot he noticed where as they show different pattern compared with single void and serial void models in $\Phi$-Q-N analysis. Considering these results may leads us to the conclusion that, in the evaluation of insulating products through PD test, it is not sufficient to determine only PDIV or existence of PD at predetermined voltage level. We could evaluate more accurately by considering all the available data such as PDIV, PD magnitude, PD occurring phase, number of PD pulses, and etc.