• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 춘계학술대회논문집
• /
• pp.1848-1853
• /
• 2000

Cause and the elimination method for the chattering phenomena were investigated the check valve attached exit of the auxiliary cooling water pump at a korean nuclear powerplant. From the site experiment and numerical calculation the incident angle of the disk was so small that it was not able to produce the lifting force to overcome the component of disk weight. Moreover, it turned out that the installed position was not symmetric for the secondary vortical flow generated inside the elbow, so that the flow structure had strongly unstable flow characteristics. From this technical support, the tapping noise and the chattering phenomena were eliminated exactly by changing the incidence angle of the valve disk and installed position of the check valve.

• 제어로봇시스템학회논문지
• /
• 제16권1호
• /
• pp.90-95
• /
• 2010

This paper describes the development of integrated head and eye tracker system. Vision based head tracker is performed and it has 7mm error in 300mm translation. The epi-polar method and point matching are used for determining a position of head and rotational degree. High brightness LEDs are installed on helmet and the installed pattern is very important to match the points of stereo system. Eye tracker also uses LED for constant illumination. A Position of gazed object(3m distance) is determined by pupil tracking and eye tracker has 1~5 pixel error. Integration of result data of each tracking system is important. RS-232C communication is applied to integrated system and triggering signal is used for synchronization.

• 한국정밀공학회지
• /
• 제24권6호
• /
• pp.66-71
• /
• 2007

Development of a locomotive mechanism for the capsule type endoscopes will largely enhance their ability to diagnose disease of digestive organs. As a part of it, there should be provided a detection device of their position in human organs for the purpose of observation and motion control. In this paper, a permanent magnet outside human body was employed to project magnetic field on a capsule type endoscope, while its position dependent flux density was measured by three hall-effect sensors which were orthogonally installed inside the capsule. In order to detect the 2-D position data of the capsule with three hall-effect sensors including the roll, pitch and yaw angle, the permanent magnet was extra translated during the measurement. In this way, the 2-D coordinates and three rotation angles of a capsule endoscope on the same motion plane with the permanent magnet could be detected. The working principle and performance test results of the capsule position detection device were introduced in this paper showing that they could be also applied to 6-DOF position detection.

• 한국항해항만학회지
• /
• 제46권4호
• /
• pp.313-320
• /
• 2022

해상에 설치된 등부표는 기상, 통항선박에 의해 생성된 외력 등에 영향을 받아 위치가 항상 유동적이다. 등부표의 위치는 항로표지용 AIS와 RTU를 통해 확인 가능하다. 본 연구는 최근 5년간(2017-2021년) 등부표의 위치데이터를 분석하여 등부표의 최대 이출위치를 분석하였다. 연구결과 등부표의 위치데이터는 기본오류가 17.9%가 존재하였다. 또한 분석대상 등부표 197기의 이출위치 오류는 70.64%이고, 장비별로는 항로표지용 AIS 보다는 RTU가 심하였다. 한편, 등부표의 위치데이터를 플로팅한 결과 4가지 유형으로 구분되었다. 가장 일반적인 침추중심형, 침추를 중심으로 위치가 2개 구역으로 구분되는 침추중심 2분형, 중심이 변동된 중심 이동형 그리고 일정기간 위치가 중심을 벗어나는끌림형이다. 침추중심형(유형-1)을 제외하고는 등부표가 설치된 위치에 따라 유형이 결정되었다. 본 연구는 등부표의 위치데이터를 분석한 첫번째 연구로서 본 연구가 등부표 위치데이터의 품질 향상에 기여하기를 기대한다.

• 한국항해항만학회지
• /
• 제47권4호
• /
• pp.231-238
• /
• 2023

등부표는 조류, 바람 등 외력에 영향을 받아 위치가 항상 유동적이고 위치는 항로표지용 AIS 또는 RTU를 통해 확인할 수 있다. 위치 확인이 가능한 등부표의 최근 5년간(2017~2021년) 위치 데이터 분석 결과 위치 오류 데이터는 평균 15.4%로 나타났으며 항해 안전사고예방 및 관리를 위해서는 위치 오류 데이터를 검출하고 정제된 위치 데이터 획득이 필요하다. 본 연구에서는 항로표지용 AIS 또는 RTU를 통해 획득한 위치 데이터를 DBSCAN Clustering하여 위치 오류 데이터를 검출하고 정제된 위치 데이터를 획득하고자 한다. 이를 위하여 위치 오류가 가장 많은 서해 해역 중 RTU가 설치된 군산항 1호 등부표의 21년도 위치 데이터를 Python library를 사용하여 DBSCAN Clustering 하였다. DBSCAN Clustering에 필요한 minPts는 2차원 데이터에 일반적으로 사용하는 값을 적용하였고 epsilon은 k-NN(최근접 이웃)알고리즘을 사용하여 값을 산출 및 적용하였다. DBSCAN Clustering 결과 minPts와 epsilon을 만족하지 못하는 위치 오류 데이터를 검출하였고 정제된 위치 데이터를 획득할 수 있었다. 본 연구는 항로표지용 AIS 또는 RTU가 설치된 등부표의 신뢰성 있는 위치 데이터를 획득할 수 있는 기초 자료로 활용할 수 있으며 항해 안전사고 예방에도 큰 도움이 될 것으로 판단된다.

• 조명전기설비학회논문지
• /
• 제26권11호
• /
• pp.1-8
• /
• 2012

The road lightings have made our living environment safe and active, since it was first installed in 1900 in Korea. As the industry developed, various kind of road lightings have been installed in an outdoor area. But the spilt light from the road lightings have caused health problem like the sleeplessness, the depression, the failure to thrive and the nearsightedness to children. The light trespass caused by road lightings vary with the height of road lightings, the distance from road lightings to the window and the BUG rating of road lightings. In this paper, we analyze the effect on the light trespass by the spatial installation position of road lightings using by RELUX program. And we derive the characteristics of the light trespass according to the spatial installation position of the road lightings in residential area near road.

• 한국농공학회지
• /
• 제19권3호
• /
• pp.4483-4491
• /
• 1977

The results obtained are as follows; 1. The variation of the temperature in a vinyl house without heating system is similar to that of air temperature in a day. The difference of maximum temperature and minimum one in a day is 27$^{\circ}C$ which is two times greater than the daily difference of air temperature. 2. When the length of the duct is increased, the high temperature zone is built up in the direction of warm air discharge from the duct, and the low temperature zone is built up in the opposite direction of warm air discharge. But, in case of the duct length is short (0.05 L), the temperature distrubution in a vinyl house become uniform. It is concluded that the shorter length of the duct, the better the distribution of the temperature in a vinyl house is. 3. When the duct is installed at high position, the high temperature zone is built up in the upper zone of the vinyl house and the low temperature zone is built up in the lower zone. And when the position of the duct is low, the rate of temperature variation along the vertical direction become high, and the direct contact of warm air with the plant in the house is occured. It is concluded that the duct should be installed at the position of slightly higher than the plant height. 4. When the fuel consumption rate is fixed at the 101/hr, the lowest temperature warming rate in the vinyl house is 5$^{\circ}C$ without regard to the air temperature.

• 제어로봇시스템학회논문지
• /
• 제11권11호
• /
• pp.930-935
• /
• 2005

In this paper, position tracking control of an autonomous helicopter is presented. Combining an LQR method and a proportional control forms a simple PD control. Since LQR control gains are set for the velocity control of the helicopter, a position tracking error occurs. To minimize a position tracking error, neural network is introduced. Specially, in the frame of the reference compensation technique for teaming neural network compensator, a position tracking error of an autonomous helicopter can be compensated by neural network installed in the remotely located ground station. Considering time delay between an auto-helicopter and the ground station, simulation studies have been conducted. Simulation results show that the LQR with neural network performs better than that of LQR itself.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.1008-1013
• /
• 2005

In this paper, position tracking control of an autonomous helicopter is presented. Velocity is controlled by using an optimal state controller LQR. A position control loop is added to form a PD controller. To minimize a position tracking error, neural network is introduced. The reference compensation technique as a neural network control structure is used, and a position tracking error of an autonomous helicopter is compensated by neural network installed in the remotely located ground station. Considering time delays between an autonomous helicopter and the ground station, simulation studies have been conducted. Simulation results show that the LQR with neural network compensation performs better than that of the LQR itself.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.91-94
• /
• 2001

In this paper, we proposed localization method of mobile robot using color landmark mounted on ceiling. This work is composed 2 parts : landmark recognition part which finds the position of multiple landmarks in image and identifies them and absolute position estimation part which estimates the location and orientation of mobile robot in indoor environment. In landmark recognition part, mobile robot detects artificial color landmarks using simple histogram intersection method in rg color space which is insensitive to the change of illumination. Then absolute position estimation part calculates relative position of the mobile robot to the detected landmarks. For the verification of proposed algorithm, ceiling-orientated camera was installed on a mobile robot and performance of localization was examined by designed artificial color landmarks. As the result of test, mobile robot could achieve the reliable landmark detection and accurately estimate the position of mobile robot in indoor environment.