• Proceedings of the KIEE Conference
• /
• 1987.11a
• /
• pp.197-199
• /
• 1987

This paper is investigated on characteristics of photoresist using inorganic a-$Se_{75}Ge_{25}$. The sensitivity of negative photoresist showing insolubility against alkalie solution, with Ag-photodoped, is more prominent than that of positive photoresist used with only a-$Se_{75}Ge_{25}$. It is also showed that the contrast of negative photoresist, ${\gamma}=2.9$, is more prominent than that of positive photoresist, ${\gamma}=1.4$.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.3
• /
• pp.196-200
• /
• 2006

We are developing a phase change etching technology using an inorganic photoresist of GeSbTe film which is the recording material of the phase change disc. A selective etching phenomenon between amorphous and crystalline states can be utilized with an alkaline etchant. Phase-change pits could be formed using this technique, in which the etching selectivity is strongly dependent on the concentration of the etchant. The degree of etching was investigated by the transmittance between crystalline and amorphous films after the wet-etching. The pits patterned on the disc could be observed by AFM after wet-etching.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.3
• /
• pp.159-163
• /
• 2014

More accurate CD (Critical Dimension) control is required for the nanometer-scaled devices. However, since the reflectivity between substrate and PR (Photoresist) becomes higher, the CD (Critical Dimension) swing curve was intensified. The higher reflectivity also causes PR notching due to the pattern of sub-layer. For this device requirement, it was optimized for the thickness, refractive index(n) and absorption coefficient(k) in the bottom anti-reflective coating(BARC; SiON) and photoresist with the minimum reflectivity. The computational simulated conditions, which were determined with the thickness of 33 nm, n of 1.89 and k of 0.369 as the optimum condition, were successfully applied to the experiments with no standing wave for the 0.13um-device. At this condition, the lowest reflectivity was 0.44%. This optimum condition for BARC SiON film was applied to the process for 0.13um-device. The optimum SiON film as BARC to PR and sub-layer could be formed with the accurate CD control and no standing waver for the nanometer-scaled semiconductor manufacturing process.

• Electrical & Electronic Materials
• /
• v.1 no.4
• /
• pp.295-302
• /
• 1988

본 연구에서는 미세패턴 형성을 위한 비정질 $Se_{75}Ge_{25}$박막의 네가티브형 포토레지스토에 대하여 고찰하였다. 습식현상공정을 통해 대비도가 포지티브형인 경우 1.4였고 네가티브형인 경우 2.9를 나타내어 네가티브형인 경우가 미세선폭 조절능력이 더 우수함을 알 수 있었다. 표면사진으로부터 약 1.mu.m정도의 미세패턴을 얻었음을 확인할 수 있었다.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.36 no.9
• /
• pp.636-639
• /
• 1987

In this study, we investigate the etching characteristics of a-Se75 Ge25 thin films. Etching properties are revealed as a function of obliqueness, temperature and concentraction of the etching solution. As the increase of obliqueness, selective etching effect increase rapidly by 35% at 80 obliqueness, and the etching rate increase the elevated temperature of the solution. The change of etching rate with obliqueness are related closely to the optical change due to the band gap illumination. We obtained clear pattern of 1.5um linewidth.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.29 no.3
• /
• pp.310-321
• /
• 2019

Objectives: The purpose of this study was to investigate types and characteristics of chemical substances used in LCD(Liquid crystal display) panel manufacturing process. Methods: The LCD panel manufacturing process is divided into the fabrication(fab) process and module process. The use of chemical substances by process was investigated at four fab processes and two module processes at two domestic TFT-LCD(Thin film transistor-Liquid crystal display) panel manufacturing sites. Results: LCD panels are manufactured through various unit processes such as sputtering, chemical vapor deposition(CVD), etching, and photolithography, and a range of chemicals are used in each process. Metal target materials including copper, aluminum, and indium tin oxide are used in the sputtering process, and gaseous materials such as phosphine, silane, and chlorine are used in CVD and dry etching processes. Inorganic acids such as hydrofluoric acid, nitric acid and sulfuric acid are used in wet etching process, and photoresist and developer are used in photolithography process. Chemical substances for the alignment of liquid crystal, such as polyimides, liquid crystals, and sealants are used in a liquid crystal process. Adhesives and hardeners for adhesion of driver IC and printed circuit board(PCB) to the LCD panel are used in the module process. Conclusions: LCD panels are produced through dozens of unit processes using various types of chemical substances in clean room facilities. Hazardous substances such as organic solvents, reactive gases, irritants, and toxic substances are used in the manufacturing processes, but periodic workplace monitoring applies only to certain chemical substances by law. Therefore, efforts should be made to minimize worker exposure to chemical substances used in LCD panel manufacturing process.