• Korean Journal of Human Ecology
• /
• v.21 no.3
• /
• pp.551-565
• /
• 2012

The primary goal of this study was to provide a systematic methodology of utilizing 3D technology for tight-fit performance sportswear using information of skin deformation in various posture. Technical tools used in this study are Cyberware whole body scanner, RapidForm2004, 2C-AN 3D pattern development program, and YukaCAD. Analysis of the 3D skin deformation while knee joint was bent from $0^{\circ}$ to $60^{\circ}$ revealed that the length of dermatomes L4 was remained consistent during knee bending. Therefore, L4 was chosen as a major cutting line. To develop a highly ergonomic pattern, replicas of static and dynamic postures were developed and integrated using two methods, one is morphing method (Sqirlz Morph), and the other is AutoCAD. Experimental tight-fit garments called 'Derm-Mov Pattern' was designed using dematomes L4, L2, and inner line under knee and compared with four other patterns. As results, AutoCAD was appropriate as a integrating method of various postures. In wear test, 'Derm-Mov Pattern' was rated high (p < .001), in terms of pressure comfort especially around front crotch area. However, wear sensation was not signipicantly different in other area due to highly extensible property of materials. Pressure distribution was relatively even in these experimental garments.

• Fashion & Textile Research Journal
• /
• v.14 no.4
• /
• pp.660-668
• /
• 2012

The purpose of this study is to analyze the thermal characteristics of garments marketed for Korean males and to investigate the influence of each garment on ensemble, by measuring their insulation values(clo) using thermal manikins. The results are as follows. The total insulations(clo) of ensembles for S/S seasons are between 1.46 and 2.6 clo, with the mean of 2.12 clo. The insulation in the still air condition is 1.23 clo, which means a decrease of 42% compared to the total insulation of all the component garments. The insulation of ensembles for S/S seasons in the dynamic air condition decreased by 46.8%, compared to the still air condition. The total insulation(clo) of ensembles for F/W seasons is between 3.84 and 7.36 clo with the mean of 4.74 clo. The insulation in the still air condition is 2.26 clo, which means a decrease of 53.6% compared to the total insulation of all the component garments. The insulation of ensembles for F/W seasons in the dynamic air condition decreased by 36.2%, compared to the still air condition. As the clo value of each component garment gets higher, the insulation of ensembles gets higher. Especially, the insulation of ensembles was more influenced by outer wear than inner wear. The insulation of ensembles could be predicted by the insulation of outerwear better.

• Journal of the Korean Society of Costume
• /
• v.52 no.2
• /
• pp.71-80
• /
• 2002

The purpose of this study was to examine the correlation between the shape of the foot and foot abrasion. and to provide preliminary data for shoe manufacturing by comparing the length of a woman's feet and the shoe size. The Martin calibrator and measuring tapes were utilized to measure the shapes of 163 female college students' feet. Indirect measurements were also obtained by line drawing of the feet for additional analysis. Brief questionnaires about what type of shoes are worn were given to the subjects of the study. Data analysis was presented by frequency, percentage, and standard deviations. Factor analysis and correlation co-efficiency of data was conducted on the significance level of p〈.05. The results of the study are as follows (1) The average number of days per week in which the subjects wear ladies' shoes per week were 4.5. Little over half of the subjects (53.87% ) answered that they wear heeled shoes for more than 8 hours per day. The most preferred height of a ladies'shoe heel was between 2 cm and 4 cm, as replied by 41.0% of the subjects. (2) The foot area where abrasion occurs most often was around the heel (51.2%) and the middle part of the sole (50.9%) (3) Factors correlated to the heel abrasion included the circumference and the breadth of the foot. The abrasion on the side of the first toe of mid-sized feet was most affected by the angle of the first the and inner foot line. The height of the foot heel was a significant factor for the abrasion near the anklebone. In conclusion, the abrasion resulted from the inappropriate fitting of the shoe and the foot. Also, the circumference and the width factors were more influential rather than the foot length. Therefore, more database on this should be systemized and available to the footwear manufacturers and the customers for more practical use of shoe size and public education.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.26 no.11
• /
• pp.1582-1592
• /
• 2002

The purpose of this study is to suggest production planning model for women's apparel manufacturer, which are relevant to the situation of Korean clothing industry. The research was based on simulation method. The basic model for the simulation was developed based on the empirical data from six production fm. After verifying the basic model, low alternative production plans went through trial run. In order to suggest the application of these alternative production plans for various style numbers and lot sizes, the simulation results were compared in terms of product efficiency and product cost. The four alternative plans were as follows: 1. The first alternative was to spread out work loads among workers in order to resolve bottlenecks in work flow. So this was suited to manufacturers that had constant production without regard to changing seasons. 2. The second alternative was to merge the skirt and trouser production, which require less work load, in one line. In this line, a few machine was justified by production improvement. It was suited to cases which producted various style suits. The third and fourth alternative were using another subcontractor for assembling inner shell garments. These was compatible in manufacturers which had to product more styles and sizes of trousers and skirts than those of upper garments. 3. The third alternative was to reassign the same workers in production line. Thus, production was increased. 4. The fourth alternative was to except two worker in production line, so expenses of worker's wage was decreased. The four alternatives could be one of the cost effective manufacturing plans according to manufacturer situations.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.6
• /
• pp.753-760
• /
• 2007

For protection of the cylinder wall of the ball mill for grinding raw ore. the inner side of the cylinder is covered with rubber liner. The rubber is easily worn down because the rubber relatively soft compared with raw ore. So the rubber liner in the ball mill cylinder must be replaced almost every year and the cost for replacing rubber liner formidable. In this paper, for reducing or excluding the cost of replacing rubber liner the basalt liner is designed. The basalt materials are generally harder than raw ore and the basalt liner in the ball mill does not wear down and so it can be used almost permanently. The concave surfaces are made on the liner of the ball mill and the liner in the cylinder wall plays also the role of raising the steel balls mixed in the raw ore. The section profiles of the concave surface have an important effect on the performance of the ball mill. The deep concave grooves raise the steel balls to high levels and give the large potential energy to the steel balls impacting to the raw ore. But if the concave grooves are too deep. the steel balls raised too high by the concave grooves fly along the parabolic path and reach to the other side of cylinder wall and so the steel balls do not play the roles of grinding the raw ore. The forces acting to a steel ball in a concave groove of the cylinder liner are also analyzed in this paper. The formulas calculating the height and the impact point of the steel ball are introduced and presented. Based to these formulas, the optimum section profiles of the basalt liner are presented.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.7
• /
• pp.723-730
• /
• 2012

During the cold wire-drawing process, the diameter of a wire is reduced and the length of the wire is increased as the wire passes through the die. The pressure and sliding motion at the interface between the wire and die cause elastic recovery of the workpiece and friction and wear on the die. In addition, wire deformation and frictional heating raise the temperature of the wire and die, resulting in difficulty in manufacturing the drawn products according to a designated inner diameter of the die, deviating from the designated dimension or the inner diameter of the die. In this study, considering the die temperature distribution, the effects of dimensional changes of the drawn products were analyzed quantitatively; these changes are caused by the elastic deformation of the die, the elastic recovery of the workpiece, and the thermal deformation of both the die and the workpiece. It was confirmed that the elastic recovery of the workpiece influenced these changes the most. The initial dies considering these factors could avoid deviation from the designated dimension, and the desired drawn products were obtained by using the designed initial drawing dies.

• Journal of Korean Vacuum Science & Technology
• /
• v.6 no.2
• /
• pp.105-107
• /
• 2002

a-C:H films were coated on windows of mobile telephone by RF plasma chemical vapor deposition equipment made in our company. Thickness of the coatings is about 0.7 micrometers and they have high hardness, low friction coefficient, good adhesion, high optical transparency and chemical inertness. Knoop hardness of the diamond-like carbon films on glass substrate is 2328 kg/mm$^2$. The adherence between films and substrate is good and shows to be 69 N by scratching test. The optical performance is improved obviously owing to coat the film on it. The index of the coated windows is 2.5, transmission of visible light is larger than 90%, and transmission of ultraviolet light decreases by 30% and the ultraviolet light can be obstructed obviously. The coated glass also has self-clean effect and decontamination ability. The films have hydrophobic character and the soakage angle of water drop is larger than 90 degrees. The windows have fog-proof ability owing to eliminate the capillary phenomena in the inner surface. The physics and chemical properties of the coated windows are steady. Study indicates that the performance of a-C:H coated mobile phone windows are improved notably on wear-resistance, corrosion-proof and optical properties and it is excellent mobile windows protective coatings.

• Fashion & Textile Research Journal
• /
• v.16 no.6
• /
• pp.971-978
• /
• 2014

This study investigates the developmental conditions of functional clothes for the elderly. First, preceding studies and relevant web sites were analyzed along with a survey of commercial functional elderly clothes in Korea. A KIPRIS patent information database was used to study registered and disclosed patents and utility models in order to analyze patent application trends in relevant fields. Patents were searched by year of application from 1990 to 2013. Keywords used for searching included 'senior, aged, and elderly'. Among collected data, overlapping and irrelevant data were excluded to select 162 cases for analysis. Details of analysis are annual patent application trends of functional elderly clothes, topic analysis, shape and characteristics. An examination of commercially available functional clothing products for the elderly indicated that most of products were developed in the form of inner wear or protective clothing for seniors who have bodily discomfort. An annual patent application of functional elderly clothes showed slight fluctuations; however, there was an overall increase. For patent topics, technologies related to secretion and excretion were the most at 47 cases total (29%), followed by 23 cases (14%) on biometric information technology. However, the development of relevant technologies seems necessary in the future as therapeutic function and fiber technologies gradually stagnate.

• Fashion & Textile Research Journal
• /
• v.3 no.1
• /
• pp.15-19
• /
• 2001

The purpose of this study was to determine the thermal characteristics of men's suits ensembles and their fabrics. For the study, 100% wool fabrics were woven with various fabric structure, fabric density and yam count and With the use of these, 12 men's suits were made with the same design. Physical characteristics that affect thermal transport properties, including drapery, cover factor; bulk density, keeping warmth ratio, vapor permeability, air permeability and porosity of the fabrics were measured. In addition, thermal resistance of men's suit ensembles, including Y-shirts, inner wear and socks was measured on the thermal manikin in the environmental chamber. The result of the study was as follows: 1. In terms of fabric structure, keeping warmth ratio of plain woven fabrics was higher than those of twill and satin woven fabrics and also, vapor and air permeability and porosity of plain woven fabrics were higher than those of twill and satin woven fabrics. 2. The result showed that thermal resistance of 12 ensembles were in the range of 0.77clo~0.97clo. 3. There was little correlation between woven condition such as, including structure, fabric density and yam count and thermal resistance of ensembles.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.41 no.3
• /
• pp.420-432
• /
• 2017

This study examined user needs for compression pant development for women with pes planus in their 50s and 60s. A total of 355 women aged 50 to 69 participated in the survey and interview. Questions were asked if they had pes planus, the using condition of foot orthotic, inconveniences during gait, and wearing condition of compression pants. The results showed that 42 (11.8%) women had pes planus. Orthotic insole and arch support were used most frequently. The most uncomfortable aspect of foot orthotic (n=146) was that it was difficult to use unless they were going outside. Participants with pes planus responded that they felt discomfort on the inner area of propodium, metatarsus, ankle, and knee during gait. The purchase and wearing rate of compression pants were not high; however, compression pants were purchased with specific needs and purposes. Respondents mainly wore the compression pants for sports activities. M size was the most frequently worn size. They preferred high waist type leggings and there was a need to increase the compression strength of the waist, thigh, knee and ankle. Additionally, the ease of donning and doffing were discussed.