• 소성∙가공
• /
• 제12권6호
• /
• pp.566-571
• /
• 2003

The metal forming behavior and defect formation in Ti-6Al-4V tube during hot backward extrusion were investigated. Dynamic material model(DMM) including Ziegler's instability criterion was employed to predict the forming defects such as shear band, inner and/or surface cracks. This approach was coupled to the internal variables generated from FE analysis. The simulation results fur the backward extrusion were compared with the experimental observation. The chilling effect and friction indicated a great influence on the deformation mode of the tube and the formation of surface cracks. The formation of forming defects in the extruded tube was attributed to non-uniform distribution of strain, strain rate and temperatures in the extruded tubes for the given test conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권4호
• /
• pp.473-479
• /
• 1999

The two-microphone sound-intensity technique has been used for the detection of defects in ra-ally loaded ball bearings. The difference in the sound-intensity levels measured for bearings with no defect and for those with intentionally introduced defects of different sizes n heir elements under various operating conditions of loads and speeds is demonstrated. The results show that of an inner-race or ball defect. It is difficult to detect defects at lower speeds. Sound-pressure measurements were also performed for comparison and it shown that the detectability of defects by sound-intensity measurements is better than that by sound-pressure measurements.

• 한국광학회지
• /
• 제16권3호
• /
• pp.239-247
• /
• 2005

본 연구에서는 물체의 내부 결함 측정을 위해서 레이저 스페클에 바탕을 둔 dual-beam shearography 기술을 이용하였다. 층 밀림을 만들기 위해서는 여러 가지 간섭계 중에서 마이켈슨 층 밀림 간섭계를 사용하였다. 열전도도가 낮은 아크릴 판 내부에 인위적인 결함을 만들어서 시료로 사용하였다. 시료에 레이저 beam을 조사하여 산란된 빛을 마이켈슨 층 밀림 간섭계를 통하여 스페클 간섭무의를 얻었으며, 위상이동기술을 통하여 위상도를 얻었다. 단일 beam을 시료에 조사할 경우, 물체의 변형의 in-plane과 out-of-plane 성분이 혼합된 상태로 측정되기 때문에 결함에 대한 정확한 분석이 불가능하다. 따라서 두 성분을 분리하기 위해서 dual-beam shearography 기술을 도입하였다. 내부 결함이 있는 시료에 이중 beam을 조사하여 변형 전의 간섭 스페클을 얻고, 약간의 전기 열을 가하여 미세한 변형을 가한 후의 간섭스페클을 얻은 후 의 위상도를 얻은 후 LS filtering과 unwrapping 처리를 통하여 내부 결함 부위를 쉽게 알아볼 수 있도록 하였을 뿐 아니라, 외력에 의한 물체의 미세 변형에 따른 결함 부위에서의 in-plane과 out-of-plane 변형성분의 위상도와 대략적인 변형 정도를 알아낼 수 있었다. 전기 열에 의한 내부결함이 있는 아크릴 판의 변형은 주로 z 방향(out-of-plane)으로 일어났으며 이것은 낮은 열전도도 때문이라는 예측과 잘 일치하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1995년도 춘계학술대회논문집
• /
• pp.62-70
• /
• 1995

The inner pulley is automobile component used as airconditioner clutch assembly. in cold forging of the inner pulley . the design conditions are the same between inner length and outer length, the uniform hardness and the no shape change in inner fillet radius due toa piercing. In industries, the design of forging processes is performed based on an experience-oriented technology, that is, designer's experiences and expensive trial and error. Using the rigid -plastic finite element simulation, we propose the optimal process conditons and design of preform or redesign of final product shape without defects prodicted by metal flow, distribution fo strain, forging load during forging processes form initial workpiece to final product.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1442-1447
• /
• 2003

Computer is a very powerful machine which is widely using for data processing, DB construction, peripheral device control, image processing etc. Consequently, many researches and developments have progressed for high performance processing unit, and other devices. Especially, the core units such as semiconductor parts are rapidly growing so that high-integration, high-performance, microminiat turization is possible. The packaging in the semiconductor industry is very important technique to de determine the performance of the system that the semiconductor is used. In this paper, the inspection of the inner defects such as delamination, void, crack, etc. in the semiconductor packages is studied. ESPI which is a non-contact, non-destructive, and full-field inspection method is used for the inner defect inspection and its results are compared with that of C-Scan method.

• 대한두개안면성형외과학회지
• /
• 제18권3호
• /
• pp.214-217
• /
• 2017

The reconstruction of the mandibulofacial defects is a difficult task when there are full-thickness cheek defects involving mandible, inner mucosa and outer skin. There are several reconstructive options for the coverage of large defects, but most of the methods are complicated, and time- and effort-consuming. We hereby present a case of fibula osteocutaneous flap based on a single peroneal artery perforator in the reconstruction of a three-dimensional mandibulofacial defects.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제17권3호
• /
• pp.224-235
• /
• 2017

Purpose: Reliability is the most important factor to detect defects as wind turbines are deployed in large blades. The methods of detecting defects are various, such as non-destructive inspection and thermal imaging inspection. We propose the phased array ultrasonic testing method of non-destructive testing. Methods: We propose the active pressure mechanism for wind power blade. The phase array ultrasonic inspection method is used for fault detection inner blade surface. Controlled pressure of mechanism with respect to z-axis is important for guarantee the result of phase array ultrasonic inspection. The model based control and proposed mechanism are utilized for overall system stability and effectiveness of system. Result: The result of proposed pressure mechanism B is more stable than A. Convergence speed is also faster than A. Conclusion: We confirmed the performance of the proposed constant pressure mechanism through experiments. Non-destructive testing was applied to the specimen to confirm the reliability of detecting defects.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제18권4호
• /
• pp.746-757
• /
• 1996

Bony defects may be found as a result of congenital anomalies, traumatic injury, automobile collisions and industrial accidents in the maxillofacial area. Such conditions are often associated with severs functional and esthetic problem. Various surgical procedure has been utilized in attempts to repair and reconstruct bony defects. Bone is a complex, living, constantly changing tissue. The architecture and composition of cancellous and cortical bone allow the skeleton to perform its essential mechanical functions. Periosteum covers the external surface of bone and consists of two layers : an outer fibrous layer and an inner more cellular and vascular layer. The inner osteogenic layer or cambium layer can form new bone while the outer layer firms part of the insertions of tendons, ligaments and muscles. This study was under taken to evaluate bone healing process on partial defect of calvarial bone with or without periosteum in rat. We made calvarial defects of different size(4mm, 6mm, 8mm) with periosteum or without periosteum in rat to study the effect of defect size on healing process. Control and experimental groups sacrified at 1, 2, 4, 6, 8 weeks, postoperatively. We examed the specimens by gloss findings, light microscophy, and fluorescent microscophy. The results were as follows. 1. Gloss findings: Control groups are larger bony defects than experimental groups after 2 weeks, and than control groups advanced healing of defected bone but experimental groups are lesser after 4, 6 weeks. After 8 weeks, bone defect has not been identified in control and experimental groups. 2. Light microscope: All defects of control groups are larger bony defects than experimental groups after 2 weeks. And than control groups show smaller defect after 4 weeks. After 8 weeks, the control group reveal pin-point sized, hardly identifiable defect space and the experimental group reveal small, but definite defect space. 3. Fluorescent microscope : Each week, new bone formation of control group is very similar to the experimental group. In this study, Osteogenesis of calvarial bone defects with periosteum or without periosteum was examined for 8 weeks in rats. The replaced periosteum had batter new bone formation than the removed periosteum.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.347-350
• /
• 2003

The metal forming behavior and defect formation in Ti-6Al-4V tube during hot backward extrusion were investigated. To predict the forming-defects such as shear band, inner cracks or surface cracks, dynamic material model(DMM) including Ziegler's instability criterion and modified Cockcroft-Latham fracture criterion(C-L model) were used. These models were coupled to the internal variables generated from FE analysis. The chilling effect and friction indicated a great influence on the deformation mode of the tube and the formation of surface cracks. The simulation results for the backward extrusion were compared with the experimental observations.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1994년도 춘계학술대회 논문집
• /
• pp.80-91
• /
• 1994

This study aims detecting forming defects for the forming process of bearing rings, which is designed by an industry expert. The designed process consists of one forming operation for the outer ring and four operations for the inner ring. The thickness of the sheet used is 1.6mm, and is in between of thin sheet and bulk material. Here the rigid-plastic finite element method is applied to the analysis and design of the process without considering anisotropy of thin sheet. Thinning and folding defects are detected if the initially designed process is applied for manufacturing. so a new process is designed by referring the results of the FEM. It is confirmed that the industry expert agree the possibility of defects derived from FEM results.