• Explosives and Blasting
• /
• v.40 no.3
• /
• pp.33-43
• /
• 2022

In order to minimize the impact on the structure during an internal explosion, the explosives storage must be kept at a distance from the inner wall to prevent the sympathetic detonation of the others explosives in an unexpected explosion. For safe explosives storage, a gap test was conducted by simulating the split arrangement of explosives inside the storage. In this study, the separation distance and arrangement between the emulsion explosives were applied differently to be sympathetic detonation at 2D of diameter and non-detonated at 2.5D. Considering the coefficient of detonation transmission and the size of the explosives storage, the explosive amount of 3kg was set, and most of the gap tests according to various arrangement changes were non-detonated, and safety was confirmed when applying the batch.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.11
• /
• pp.121-126
• /
• 2021

In this study, the effect of thermal contact resistance between pin-channel tubes on the heat transfer characteristics was analytically examined around the channel tubes with the pins attached to two consecutive arranged channel pipes. The numerical results showed that the heat transfer coefficient decreased geometrically as the thermal contact resistance increased, and the corresponding temperature change on the contact surface increased as the thermal contact resistance increased. The thinner the pin, the more pronounced the geometric drop in the heat transfer coefficient. It was confirmed that the higher the height of the pin, the higher was the heat transfer coefficient, however, the greater the size of the thermal contact resistance, the smaller was the heat transfer coefficient. It was found that the temperature change in the inner wall of the channel tube did not significantly affect the heat transfer characteristics owing to the thermal contact resistance. Furthermore, the velocity of air at the entrance of the channel tube was proportional to the heat transfer coefficient due to a decrease in the convective heat resistance corresponding to an increase in the flow rate.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.26 no.1
• /
• pp.1-11
• /
• 2022

In a gas turbine, fuel is exposed to a high temperature environment until it is fed to the combustor through the injector. Hydrocarbon fuels can coke under high temperature conditions, which can cause coking material to deposit on fuel lines or block the injector passages. In this study, a specimen simulating a fuel line located inside a gas turbine and Jet A-1 were heated using electric devices. Jet A-1 coking tests were performed by changing the wall temperature of the stainless steel specimen and the temperature of Jet A-1 supplied to the specimen. After the coked specimens were cut, the coking material and the inner surface were analyzed using an energy dispersive X-ray spectrometer and a field emission scanning electron microscope.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.35 no.6
• /
• pp.594-602
• /
• 2022

Cast-resin transformers are widely installed in various electrical power systems because of their low operating cost and low influence on external environmental factors. However, when they have an internal defect during the manufacturing process or operation, a partial discharge (PD) occurs, and eventually destroys the insulation. In this paper, a Rogowski-type PD sensor was studied to replace commercial PD sensors used for the insulation diagnosis of power apparatus. The proposed PD sensor was manufactured with four different types of PCB-based winding structures, and it was analyzed in terms of the detection characteristics for standard calibration pulses and the changes of the output voltage according to the distance. The output increased linearly in accordance with the applied discharge amount. It was confirmed that the hexagon structure sensor had the highest sensitivity, because the winding cross-sectional area of the sensor was larger than others. In addition, as the distance from the defect increased, the output voltage of the sensors decreased by 7.32% on average. It was also confirmed that the attenuation rate according to the distance decreased as the input discharge amount increased. For the application of this new type sensor, PD electrode system was designed to simulate the void defect. Waveforms and PRPD patterns measured by the proposed PD sensors at DIV and 120% of DIV were the same as the results measured by MPD 600 based on IEC 60270. The proposed PD sensors can be installed on the inner wall of the transformer tank by coating its surfaces with a non-conductive material; therefore, it is possible to detect internal defects more effectively at a closer distance from the defect than the conventional sensors.

• Journal of Veterinary Clinics
• /
• v.39 no.6
• /
• pp.319-325
• /
• 2022

Two-port laparoscopic ovariectomy (Lap-OVE) has been performed in small dogs, using 3-mm and 5-mm portal sites, and is associated with reduced surgical stress and postoperative pain. However, extension of the incision is often needed to extract the ovaries. In this study, we aimed to minimize invasiveness by using smaller-sized cannulas as well as a novel technique for ovary extraction. Lap-OVE was performed on six, healthy female dogs (range, 3 to 7.2 kg) using two 3-mm midline portals. The middle finger of a size M nitrile glove was cut at its base and sterilized preoperatively. The ovary was suspended at the body wall using a 1-0 blue nylon needle, and the ovarian pedicle and ligaments were transected using a 3-mm bipolar forceps. To facilitate the glove passing through the 3.9-mm port, it was turned inside out to expose the smooth inner surface, before being inserted into the abdominal cavity with an applicator. Both ovaries were placed inside, and the mouth of the glove was exteriorized through the port with a laparoscopic grasping forceps. The ovaries were morcellated inside the glove, using Adison-Brown tissue forceps and iris scissors, which enabled safe extraction without incision enlargement. Median incision lengths were 4.3 mm (3.5-mm cranial cannula) and 4.8 mm (3.9-mm caudal cannula). An advantage of this procedure was that there was no need for skin sutures. In conclusion, using our novel technique, sutureless Lap-OVE was possible in small dogs using two 3-mm portal sites without additional incision.

• Design Convergence Study
• /
• v.14 no.4
• /
• pp.193-208
• /
• 2015

This study is to search a meaning of treagedy to show by the 6th generation through charecter's tragedy in the 6'th Generation Chinese film. For this, it examined an inner characteristic behind of the tragedy's moment and externalized ending in directors' films of the 6'th Generation's representation. The 6'th Generation of Chinese film reorganized newly Chinese film's cultural topography in the 1990s. The 6'th Generation films, which rebelled against the primary melody and the 5'th Generation on the system, is expressed commonly a tragedy moment with the time and space by character's tragedy. Characters of the 6'th Generation in the tragedy moment attempts various efforts to escape from the tragedy moment. However, no one can overcome the wall of reality, and their concealed emotion as keeping it out of the public eye lead that play. The moment that the 6th generation film meets a tragedy, the main character's accumulated tragedy situations begin to unfold all together. A tragedy embodied through : a collapsed tragedy due to the past's wound, a tragedy due to loss of jobs, a tragedy due to a family's departure, a tragedy from a time of chaos, a tragedy of a woman who became a head of a household and other tragedies.

• Wind and Structures
• /
• v.37 no.4
• /
• pp.289-302
• /
• 2023

Insulating glass units (IGUs) have been widely used in buildings in recent years due to their superior thermal insulation performance. However, because of the panel reciprocating motion and fatigue deterioration of sealants under long-term wind loads, many IGUs have the problem of early failure of watertight properties in real usage. This study aimed to propose a statistical method for wind-induced deflection of IGU panels during the whole life service period, for further precise analysis of the accumulated fatigue damage at the sealed part of the edge bond. By the estimation of the wind occurrence regularity based on wind pressure return period, the events of each wind speed interval during the whole life were obtained for the IGUs at 50m height in Beijing, which are in good agreement with the measured data. Also, the wind-induced deflection analysis method of IGUs based on the formula of airspace coefficient was proposed and verified as an improvement of the original stiffness distribution method with the average relative error compared to the test being about 3% or less. Combining the two methods above, the deformation of the outer and inner panes under wind loads during 30 years was precisely calculated, and the deflection and stress state at selected locations were obtained finally. The results show that the compression displacement at the secondary sealant under the maximum wind pressure is close to 0.3mm (strain 2.5%), and the IGUs are in tens of thousands of times the low amplitude tensile-compression cycle and several times to dozens of times the relatively high amplitude tensile-compression cycle environment. The approach proposed in this paper provides a basis for subsequent studies on the durability of IGUs and the wind-resistant behaviors of curtain wall structures.

• Horticultural Science & Technology
• /
• v.30 no.6
• /
• pp.700-708
• /
• 2012

In order to optimize a method to determine the firmness of Chinese cabbage, hardness of midrib tissues was examined based on their chronological order of emergence. Texture measurement using volodkevich bite jaws gave a consistent and highest regression ($r^2=0.85$) between firmness and the order of leaf emergence, while blade set, cylinder probe, and crisp fracture support rig showed a lower coefficient of determination. Thickness of midrib tissue within an individual head from 16 cultivars of Chinese cabbage was positively correlated with the order of emergence, becoming thinner toward inner leaves. Mean thickness of midrib tissue from the head ranged from 7.74 mm for 'CR-shingshing' and 9.28 mm for 'Norangyeorum'. The covariance of leaf thickness within a head was highly cultivar-dependent, ranging from 23.6% for 'Chihili' and 5.8% for 'Bulam'. Firmness of the midrib tissue, defined as maximum peak height per tissue thickness, became higher from outer to inner leaves, showing $2^{nd}$ order of regression. Mean firmness of the midrib tissue from individual head varied from 1.58 N for 'Rangno' to 3.46 N for 'CR-shingshing'. The $10^{th}$ or $11^{th}$ leaf brought the best correlation coefficient (r = 0.81) between firmness of an individual leaf and the mean firmness of the entire leaves in a head, suggesting a reliable and rapid method to estimate the firmness of a head in lieu of examining all leaves in the head. The relationship between firmness of midrib tissue and dry mass ($r=0.70^{**}$) as well as cell wall content ($r=0.58^*$) of the head were positively correlated. Results obtained from the present study suggested that a new method to determine midrib firmness would enable to clarify the relationship between textural quality of fresh Chinese cabbage and their processed product, 'Kimchi'. It will also be important to apply this method to screen textural quality of various genotypes under breeding programs.

• Journal of the Microelectronics and Packaging Society
• /
• v.11 no.2 s.31
• /
• pp.59-66
• /
• 2004

This paper presents a novel fabrication process for a tapered hollow metallic microneedle array using backside exposure of SU-8, and analytic solutions of critical buckling of a tapered hollow microneedle. An SU-8 meta was formed on a Pyrex glass substrate and another SU-8 layer, which was spun on top of the SU-8 mesa, was exposed through the backside of the glass substrate. An array of SU-8 tapered pillar structures. with angles in the range of $3.1^{\circ}{\sim}5^{\circ}$ was formed on top of the SU-8 mesa. Conformal electrodeposition of metal was carried out followed by a mechanical polishing using a pianarizing polymeric layer. All organic layers were then removed to create a metallic hollow microneedle array with a fluidic reservoir on the backside. Both $200{\mu}m\;and\;400{\mu}m$ tall, 10 by 10 arrays of metallic microneedles with inner diameters of the tip in the range of $33.6{\sim}101\;{\mu}m$ and wall thickness of $10{\mu}m\;-\;20{\mu}m$ were fabricated. Analytic solutions of the critical buckling of arbitrary-angled truncated cone-shaped columns are also presented. It was found that a single $400{\mu}m$ tall hollow cylindrical microneedle made of electroplated nickel with a wall thickness of $20{\mu}m$, a tapered angle of $3.08^{\circ}$ and a tip inner diameter of $33.6{\mu}m$ has a critical buckling force of 1.8 N. This analytic solution can be used for square or rectangular cross-sectioned column structures with proper modifications.

• Economic and Environmental Geology
• /
• v.43 no.2
• /
• pp.109-121
• /
• 2010

The bioleaching experiment under $42^{\circ}C$ was effectively carried out to leach the more valuable element ions from the pyrite in the Gangyang mine waste. Bacteria can survive at this temperature, as indigenous acidophilic bacteria were collected in the Hatchobaru acidic hot spring, in Japan. To enhance the bacterial activity, yeast extract was added to the pyrite-leaching medium. The indigenous acidophilic bacteria appeared to be rod-shaped in the growth-medium which contained elemental sulfur and yeast extract. The rod-shaped bacteria ($0.7\times2.6\;{\mu}m$, $0.6\times7\;{\mu}m$, $0.8\times5\;{\mu}m$ and $0.7\times8.4\;{\mu}m$) were attached to the pyrite surface. The colonies of the rod-shaped bacteria were selectively attached to the surroundings of a hexagonal cavity and the inner wall of the hexagonal cavity, which developed on a pyrite surface. Filament-shaped bacteria ranging from $4.92\;{\mu}m$ to $10.0\;{\mu}m$ in length were subsequently attached to the surrounding cracks and inner wall of the cracks on the pyrite surface. In the XRD analysis, the intensity of (111), (311), (222) and (320) plane on the bacteria pyrite sample relatively decreased in plane on the control pyrite sample, whereas the intensity of (200), (210) and (211) increased in these samples. The microbiological leaching content of Fe ions was found to be 3.4 times higher than that of the chemical leaching content. As for the Zn, microbiological leaching content, it was 2 times higher than the chemical leaching content. The results of XRD analysis for the bioleaching of pyrite indicated that the indigenous acidophilic bacteria are selectively attacked on the pyrite specific plane. It is expected that the more valuable element ions can be leached out from the mine waste, if the temperature is increased in future bioleaching experiments.